RAFM钢TIG焊和电子束焊疲劳性能实验和分析模拟

利用ANSYS 对低活化铁素体马氏体(RAFM)钢进行非熔化极气体保护焊(TIG 焊)与电子束焊的抗疲劳模拟分析，再利用SDS200 电液伺服疲劳试验机对TIG 焊和电子束焊的两种RAFM 钢试件进行实验。通过施加相同梯度负荷对TIG 焊和电子束焊试件进行焊缝的疲劳性能实验。与实验结果对比分析，结果显示电子束焊优于 TIG 焊，但在一定负载下可以用TIG 焊代替电子束焊。     

JEM-2100PLUS透射电子显微镜操作方法与技巧及常见故障排除

以JEM-2100PLUS透射电子显微镜为例，介绍了电镜的基本结构、操作面板和成像原理。使用透射电子显微镜的最终目的就是要得到高质量的照片，结合透射电镜的操作步骤，总结了如何拍摄高质量的照片以及常见故障排除方法。     

硅氧烷交联的咪唑基团功能化聚苯醚/聚四氟乙烯耐高温质子交换膜

以聚苯醚(PPO)为基体材料, 通过溴甲基化及咪唑基团功能化, 与聚四氟乙烯(PTFE)复合、 硅氧烷基团水解交联及磷酸掺杂, 制备了兼具高磷酸掺杂含量、 高质子电导率和良好机械性能的高温质子交换膜材料. 以甲基咪唑(MeIm)和咪唑基硅氧烷化合物(SiIm)为功能化试剂(其中咪唑基团提供了磷酸作用位点, 同时SiIm中的硅氧烷基团水解后得到Si—O—Si交联网络结构), 提高了膜材料的机械稳定性. 与PTFE的复合进一步增强了膜材料的机械强度. 结果表明, 复合膜具有较高的电导率和一定的机械强度. 当磷酸掺杂质量分数为242.5%时, PPO-50%SiIm-50%MeIm/PTFE复合膜在160 ℃不加湿条件下的电导率为0.09 S/cm, 室温下的断裂拉伸强度为3.6 MPa.     

Infrared laser velocity modulation spectrum of the ν3 fundamental band of HBCI+

The infrared spectrum of the ν₃ fundamental band of HBC1⁺ has been observed using the velocity modulation detection technique. The ion was produced in an ac glow discharge containing a mixture of H₂ and BC1₃. Thirty-two transitions of the fundamental band of the most naturally abundant isotopomer, H¹¹B³⁵C1⁺, between 1105 and 1170cm^?1 have been assigned. The ν₃ band origin and rotational constants have been determined to be ν₀ = 1121.5677(20)cm^?1, B ₀ = 0.63089(23)cm^?1 and B ₁ = 0.62699(21)cm^?1. A second series of lines have been attributed to the H¹¹B³⁷C1⁺ isotopomer, although it has not been possible to make an unambiguous J assignment of these lines.     

三光气与酚制备三氯甲氧基甲酸芳酯研究

研究了不同取代酚与三光气的反应,得到七种未见报道的新化合物,以IR、MS、1H NMR、13C NMR对产物进行了表征,并探索得到合适的反应催化剂、反应物浓度配比、反应时间,讨论了酚上不同取代基对反应的影响,收率在78.5～90.5%之间。     

Structure Analysis of Needle-like Copper Tantalum Trisulfide Crystals by XPS and Raman Spectroscopy

High-quality needle-like CuTaS3 single crystals have been synthesized through a chemical vapor transport(CVT)process.Crystallographic data show the special double chains of edge-sharing TaS6 octahedra....     

基于N-A型原子系统的1→N型分束器

分析N-A型原子系统的原子极化率,结果表明即使在全共振条件下,EIT效应并不一定产生,介质对信号场的色散和吸收关系与所有场的复拉比频率有关.信号场传播方程的解析分析表明,此系统可以把一束光分成不同频率的N束光,并且其强度和相位是可控的.暗态极化子分析表明它还可以用作1→N量子分束器,产生多体纠缠态.     

Effects of the laser surface treatment on the mechanical properties of CuZr-based bulk metallic glasses

Surfaces of three types of CuZr-based bulk metallic glasses (BMGs) were modified by laser surface treatment (LST), and the influence of the treatment on structure and mechanical properties of these alloys was investigated. The phase structure of as-cast and laser-treated samples was characterized by XRD and the morphology of the alloys after fracture was examined by SEM. The compressive plasticity of treated Cu47.5Zr47.5Al5 and Cu46.5Zr47.5Al5Co1 BMGs can be improved from 0.5% to 2.0% and from 1.2% to 5.7% respectively compared with the as-cast ones, while (Cu0.55Zr0.40Al0.05)99Er1 BMG shows insignificant change of plasticity. The improvement in plasticity is attributed to induced crystallization of B2 CuZr phase in the treated surface zone of selected metallic glasses.     

Co/SBA-16:对柴油组分有高选择性的费托合成催化剂(英文)

使用浸渍法制备了一系列Co/SBA-16催化剂,并通过氮物理吸附、X射线衍射、氢程序升温还原、氢化学吸附和透射电镜技术对催化剂行了表征。研究表明,随着负载钴含量的增加,金属钴的分散度降低了,这是同Co3O4晶粒增长和比表面积降低相一致的。Co/SBA-16催化剂展示了高的一氧化碳转化率,低的C1选择性和高的C5+选择性,特别对柴油组分有高选择性。