Change in the magnetic state of a surface upon formation of hydrogen bonds during adsorption

It is established that reversible adsorption of water and methyl alcohol molecules, occurring via formation of hydrogen bonds, changes the dynamic properties of domain walls in the surface region of soft ferromagnets, as well as their initial static magnetic susceptibility. A mechanism is proposed for the effects revealed.     

A model for the interaction of near-infrared laser pulses with metal powders in selective laser sintering

A thermal model of the interaction of pulsed near-infrared laser radiation from a Nd:YAG laser was made, taking the measured powder properties such as reflectance, optical penetration depth and thermal conductivity into account. It allows an estimation of the evolution of two different temperatures: the average temperature of the powder (taken over the grains in a volume given by the laser beam diameter and the optical penetration depth) and the temperature distinction within a single grain. It showed that in pulsed mode consolidation can be achieved at much lower average power as the surface of the powder particles are molten but their cores remain at nearly room temperature. This leads to a much lower average temperature and therefore a dramatic decrease in residual thermal stresses in the finished piece. The results of the model were experimentally tested and confirmed. Received: 26 July 2001 / Accepted: 23 November 2001 / Published online: 23 January 2002     

On the Use of the Restitution Condition in Flexible Body Dynamics

The difference between the classical treatment offlexible body impact and the treatment of impact in flexiblemultibody dynamics is due to several fundamental reasons. Inthe classical impact theory, simple structures such as beamsand plates are used. Infinite dimensional models can bedeveloped for these simple structural elements to study theimpact dynamics and the wave propagation problem. Flexiblemultibody impact problems, on the other hand, involve bodieswith complex geometry that cannot be modeled using infinitenumber of degrees of freedom. Furthermore, the classicalimpact theory has been mainly concerned with the impactbetween a rigid mass that moves without constraints beforeit impacts a simple flexible structure. This is not amultibody simulation scenario in which the impact occursbetween kinematically constrained bodies that are subjectedto impulsive constraint forces in addition to the impactforces. These constraint forces can influence the motion ofthe two bodies immediately after impact, and as aconsequence, the simple classical theory scenario of impactdoes not apply. It is the objective of this paper to discussthe use of the restitution condition in flexible multibodyimpact problems and demonstrate that the use of thisapproach does not exclude the classical formulation.Nonetheless, the impulse momentum balance approach can serveas an effective and efficient procedure for solving theimpact problem in finite dimensional models that do not obeythe classical wave theory. Energy results of simplestructural elements are presented in order to demonstratethe consistency of using the impulse momentum balanceapproach in solving impact problems in finite dimensionalflexible body applications.     

Geometrically qualified ESPI vibration analysis of an engine

This paper presents an application in the automotive industry where a combination of electronic speckle-pattern interferometry and laser doppler velocimetry were used at a critical stage in the design process of an internal combustion engine. Combined deformation and surface relief measurements were used to study the phase and amplitude of deformation of a vibrating engine. The relief data was combined with the interferometer geometry and used to geometrically correct the deformation data, in an effort to improve accuracy. The measurements allowed rapid identification and quantification of design weaknesses, particularly those causing undesirable resonances. This led to a significant reduction in the design time and lowering of costs, when compared with existing design optimisation methods.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

Machine assignment in a nonlinear multi-product flowline

A group of machines for processing a set of jobs in a manufacturing system is often located in a serial line. An efficient strategy for locating these machines such that the total travel distance or the cost of transporting the jobs is minimized is desired. In this research, the assumption of a linear line with equally spaced machine location is relaxed. This research addressed problems of locating unique machines. It is found that the machine distances possess unique properties in this type of a problem. Utilizing these properties, heuristic strategies are proposed to obtain efficient solution where optimal methods are expected to be computationally prohibitive. A lower bound for the optimum solution is also proposed. Results are encouraging.     

Spectral Properties of Thioflavin T and Its Complexes with Amyloid Fibrils

Comparative analysis of the absorption and fluorescence spectra and fluorescence excitation spectra of thioflavin T (ThT) in various solvents and in the composition of amyloid fibrils has shown that ThT, when excited in the region of the long-wavelength absorption band, fluoresces in the spectral region with a maximum at 478–484 nm. The appearance in aqueous and alcohol solutions of a fluorescence band with a maximum near 440 nm has been attributed to the presence in the composition of the ThT preparations of an impurity with an absorption band in the 340–350-nm range. The literature data showing that in glycerol ThT has a wide fluorescence spectrum with two maxima are due to the artifact connected with the use of a high concentration of the dye. It has been suggested that the cause of the low quantum yield of ThT aqueous and alcohol solutions is the breakage of the system of conjugated bonds due to the reorientation of the benzothiozole and benzaminic rings of ThT in the excited state with respect to one another. The main factor determining the high quantum yield of fluorescence of ThT incorporated in fibrils is the steric restriction of the rotation of the rings about one another under these conditions. The suggestions made have been verified by the quantum-chemical calculation of the ThT molecule geometry in the ground and excited states.     

Pairwise Correlations in a Multicomponent Anisotropic Liquid

We investigate a multicomponent anisotropic liquid system. The first spatial moment of the direct correlation function is taken into account to obtain asymptotic expressions for the pairwise correlation functions. In this approximation, we obtain the pairwise correlation functions that describe the system behavior not only in the critical-state neighborhood but also in the noncritical domain. We show that the critical parameters for the anisotropic system differ from those for the isotropic system.