Effects of physical aging on yielding kinetics of polycarbonate

The purpose of this work was to investigate the effects of physical aging on the kinetics of yielding in polycarbonate. PC samples were annealed over a wide range of aging times and temperatures. Both tensile and compressive tests were performed over various loading rates and temperatures to analyze the effects of aging time and aging temperature on yielding kinetics. Two grades of polycarbonate, Makrolon, of different molecular weights, PC-2608 (low M_w), and PC-3208 (high M_w), supplied by Bayer were analyzed. In unaged condition, PC is hard and tough, but after aging, it becomes more brittle. In terms of molecular movement, the yielding process is a thermally activated process involving inter- and intra-molecular motions. The time–temperature dependence of yielding behavior can be separated into two regions. Aging does not affect localized molecular motions of the β process during yielding. Physical aging in PC results in a slower jump rate of the main segments of macromolecules between two equilibrium positions. It reduces the flexibility of the macromolecules and thus, makes the polymer more brittle. Heat aging also causes a decrease of the entropy (ΔS) in polycarbonate, and this decrease is more important when the molecular weight is reduced. Increasing the annealing time and temperature results in a continuous reduction of ΔS. The rate of aging decreases with decreasing annealing temperature and below about 30 °C, no aging takes place. Annealing also strongly affects the excess of enthalpy in PC. However the effect of physical aging on yielding differs to that on enthalpy excess. The kinetics of yielding and aging processes in polycarbonate are also different. An increase in the strain rate does not have the same effect on the yield stress as an increase in the aging time by a same factor.     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Irradiation-induced reduction and luminescence properties of Sm doped in BaBPO5

Usually, Sm²⁺ ions could be reduced by heating the materials in reducing atmospheres. Exposure to ionizing radiations is also known to cause Sm³⁺→Sm²⁺ conversion. In this work, BaBPO₅ doped with the samarium ion was prepared by high temperature solid-state reaction. Sm²⁺ ions were obtained by two different reduction methods, i.e., heating in H₂ reduced atmosphere and X-ray irradiation. The measurements of X-ray diffraction (XRD), and scanning electron microscope (SEM) were investigated. It is found that the conversion of Sm³⁺→Sm²⁺ is very efficient in BaBPO₅ hosts after X-ray irradiation. Sm²⁺ ions under these two reduction methods exhibit different characteristics that were studied by measurements of luminescence and decay. The results showed that the luminescence properties of Sm²⁺ ions in BaBPO₅ were highly dependent on the sample preparation conditions.     

Codes Over the p-adic Integers

We study codes over the p-adic integers and correct errors in the existing literature. We show that MDS codes exist over the p-adics for all lengths, ranks and p. We show that self-dual codes exist over the 2-adics if and only if the length is a multiple of 8 and that self-dual codes exist over the p-adics with p odd if and only if the length is 0 (mod 4) for p ≡ 3 (mod 4) and 0 (mod 2) for p ≡ 1 (mod 4).     

Preparation and characterization of rigid poly(vinyl chloride)/MMT nanocomposites. II. XRD,morphological and mechanical characteristics

A Haake torque rheometer equipped with an internal mixer is used to study the influence of the amount of sodium montmorillonite (Na⁺‐MMT) and organically modified MMT (O‐MMT) on X‐ray diffraction (XRD), morphology, and mechanical characteristics of rigid poly (vinyl chloride) (PVC)/Na⁺‐MMT and PVC/O‐MMT nanocomposites, respectively. Results of XRD and transmission electron microscopy (TEM) indicate that MMT is partially encapsulated and intercalated in the rigid PVC/Na⁺‐MMT nanocomposites. However, results of XRD and TEM show MMT is partially intercalated and exfoliated in the rigid PVC/O‐MMT nanocomposites. Tensile strength, yield strength, and elongation at break of the rigid PVC/MMT nanocomposites were improved simultaneously with adding 1–3 wt % Na⁺‐MMT or O‐MMT with respect to that of pristine PVC. However, the addition of Na⁺‐MMT or O‐MMT should be kept as not more than 3 wt % to optimize the mechanical properties and the processing stability of the rigid PVC/MMT nanocomposites. SEM micrographs of the fractured surfaces of the rigid PVC/Na⁺‐MMT and PVC/O‐MMT nanocomposites both before and after tensile tests were also illustrated and compared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2145–2154, 2006