Bounds to optimal burn‐in and optimal work size

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we consider the problem of determining the optimal burn‐in time and optimal work size maximizing the long‐run average amount of work saved per time unit in the computer applications. Assuming that the underlying lifetime distribution of the computer has an initially decreasing or/and eventually increasing failure rate function, an upper bound for the optimal burn‐in time is derived for each fixed work size and a uniform (with respect to the burn‐in time) upper bound for the optimal work size is also obtained. Furthermore, it is shown that a non‐trivial lower bound for the optimal burn‐in time can be derived if the underlying lifetime distribution has a large initial failure rate. Copyright © 2005 John Wiley & Sons, Ltd.     

Continuously coupled parametric generators and their quantum statistics

In this paper the quantum-statistical properties of light beams propagating in a directional nonlinear coupler are investigated. This device is composed of a pair of linearly coupled nonlinear waveguides operating by means of degenerate parametric downconversion. The possibility of generation of nonclassical states of light in single and compound modes, using the short-length approximation, is discussed. Influence of linear and nonlinear mismatches for generation of nonclassical light is taken into account. This work was supported by Project LN00A015, Research Project No. CEZ: J14/98 and the COST project OC P11.003 of the Czech Ministry of Education.     

Control of self‐organized low‐dimensional morphology in poly(styrene‐b‐4vinylpyridine)/polystyrene blend thin films

The surface morphologies of poly(styrene‐b‐4vinylpyridine) (PS‐b‐P4VP) diblock copolymer and homopolystyrene (hPS) binary blend thin films were investigated by atomic force microscopy as a function of total volume fraction of PS (?_PS) in the mixture. It was found that when hPS was added into symmetric PS‐b‐P4VP diblock copolymers, the surface morphology of this diblock copolymer was changed to a certain degree. With ?_PS increasing at first, hPS was solubilized into the corresponding domains of block copolymer and formed cylinders. Moreover, the more solubilized the hPS, the more cylinders exist. However, when the limit was reached, excessive hPS tended to separate from the domains independently instead of solubilizing into the corresponding domains any longer, that is, a macrophase separation occurred. A model describing transitions of these morphologies with an increase in ?_PS is proposed. The effect of composition on the phase morphology of blend films when graphite is used as a substrate is also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3496–3504, 2004     

Detection of Pb2+ using a hydrogel swelling microcantilever sensor.

Hydrogels containing benzo-18-crown-6 were used to modify microcantilevers for measurements of the concentration of Pb2+ in aqueous solutions. These microcantilevers undergo bending deflection upon exposure to solutions containing various Pb2+ concentrations as the result of a swelling of the hydrogels. It was found that a concentration of 10(-6) M Pb2+ can be detected using this technology. Other cations, such as Na+, have no effect on the deflection of this cantilever. The cation K+, which also complexes with benzo-18-crown-6, could interfere with Pb2+ detection, but only at high concentrations (> 10(-4) M).     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Changes in the spectrum of Gaussian Schell-model beams propagating through turbulent atmosphere

Based on the extended Huygens-Fresnel principle, the spectrum of Gaussian Schell-model (GSM) beams propagating through turbulent atmosphere is derived analytically. It is shown that, if the scaling law is valid, the normalized spectrum S(ω) of GSM beams propagating through turbulent atmosphere is the same as the normalized source spectrum S⁽⁰⁾(ω), whether GSM source is quasi-homogenous or not. On the other hand, if the scaling law fails, S(ω) of GSM is different from S⁽⁰⁾(ω). The structure constant of the refractive index, transverse coordinate of observation point and spatial correlation length of the source affect the spectrum, which is illustrated numerically.     

Mössbauer and X-ray diffraction characterization of Fe60Al40 coatings prepared by thermal spraying

Microstructured (atomized) and nanostructured (milled) Fe₆₀Al₄₀ powders together with their corresponding coatings synthesized by High Velocity Oxy-fuel (HVOF) or Atmospheric Plasma Spray (APS) thermal spraying techniques have been characterized by Mössbauer Spectroscopy (MS) and X-ray Diffraction (XRD). The evolution of the microstructure and the atomic ordering degree in the powders and coatings are discussed at the light of the various processing conditions. The operational correlation between the parameters of the duplex morphology of coatings and the processing parameters is discussed.     

A Simple Bi-directional Mode Expansion Propagation Algorithm Based on Modes of a Parallel-plate Waveguide

The bi-directional mode expansion propagation algorithm (BEP) is known to be an accurate and efficient method for modelling field distribution in high-index contrast waveguide structures with strong back-reflections like Bragg gratings and photonic crystals. The main difficulty of this method is that for lossy structures, the propagation constants of modes are to be searched in the complex plane. To speed-up this procedure, a two-step algorithm for eigenmode calculation based on the expansion into the modes of an empty metallic waveguide has recently been proposed. Proper truncation rules possessing good convergence of the expansion method for both TE and TM modes have also been recently published. In this contribution, both these approaches are combined in the development of an extremely simple version of the two-dimensional BEP method that makes use of the field expansion into the eigenmodes of a parallel-plate waveguide. The method is strictly reciprocal and appeared to be computationally reliable also for strongly lossy structures. High numerical stability is ensured using the scattering matrix formalism, and an efficient method of calculating Bloch modes for symmetric as well as asymmetric periodic waveguide structures is adopted. A wide range of applicability of the method is demonstrated by a few examples.