Effect of pH on adsolubilization of single and binary organic solutes into a cationic hydrocarbon surfactant adsorbed layer on silica

The adsolubilization behaviors of 2-naphthol, biphenyl, and their binary solutes in the hexadecyltrimethyl ammonium bromide (HTAB) adsorbed layer formed on silica have been studied with solution pH. Two feed concentrations of HTAB are employed: 1.5 and 3.0 mmol dm(-3). At the feed concentration of 1.5 mmol dm(-3) HTAB, most of HTAB are adsorbed on the silica as a monolayer, while a bilayer formation occurs at the feed concentration of 3.0 mmol dm(-3). It is found that the adsolubilized amounts of respective single solutes increase with increasing solution pH except acidic region for biphenyl under a constant feed concentration of 2-naphthol (0.4 mmol dm(-3)) and biphenyl (0.047 mmol dm(-3)). The adsolubilization of binary solutes depends on the feed concentration of HTAB; at the low HTAB feed concentration, competitive adsolubilization between 2-naphthol and biphenyl occurs above pH 4.5, while at the high HTAB feed concentration the adsolubilization of biphenyl is enhanced by the incorporation of 2-naphthol over a whole pH region. These behaviors in the adsolubilization are discussed from the surfactant structure of HTAB adsorbed as well as the admicellar partitioning coefficients.     

Biodegradable Polyurethanes from Plant Components

Abstract

Polyurethane (PU) sheets and foams having plant components in their network were prepared by using the following procedure. Polyethylene glycol (PEG) was mixed with one of the following; molasses, lignin, woodmeal, or coffee grounds. The mixture obtained was reacted with diphenylmethane diisocyanate (MDI) at room temperature, and precured PUs were prepared. The precured PUs were heat-pressed and PU sheets were obtained. In order to make PU foam, the above mixture was reacted with MDI after the addition of plasticizer, surfactant (silicone oil), catalyst (di-n-butyltin dilaurate), and droplets of water under vigorous stirring. The glass transition temperature, tensile and compression strengths, and Young's modulus of the PU sheets and foams increased with an increasing amount of plant components. This suggests that saccharide and lignin residues act as hard segments in PUs. It was found that the PUs obtained were biodegradable in soil. The rate of biodegradation of the PUs derived from molasses and coffee grounds was between that of cryptomeria (Cryptomeria japonica) and beech (Fagus sieboldi).     

Recent topics of the metallacycles composed of the heavier group 14 elements

This Letter reviews recent advance of metallacycles with chelating Si-, Ge-, and Sn-ligands. Dehydrogenative bond-forming reactions of organosilanes, -germanes, and -stannanes promoted by Pd and Pt complexes afford four- and five-membered metallacycles composed of heavier group 14 elements. It has a couple of advantages such as easier preparation of the starting compounds and reaction procedure than the common metathesis reactions of dianions with transition metal dihalide complexes. These metallacycles are regarded as possible intermediates in catalytic dehydrocoupling polymerizations or as convenient precursors to form discrete oligomers.     

Response of ocean bottom dwellers exposed to underwater shock waves

The paper reports results of experiments to estimate the mortality of ocean bottom dwellers, ostracoda, against underwater shock wave exposures. This study is motivated to verify the possible survival of ocean bottom dwellers, foraminifera, from the devastating underwater shock waves induced mass extinction of marine creatures which took place at giant asteroid impact events. Ocean bottom dwellers under study were ostracoda, the replacement of foraminifera, we readily sampled from ocean bottoms. An analogue experiment was performed on a laboratory scale to estimate the domain and boundary of over-pressures at which marine creatures’ mortality occurs. Ostracods were exposed to underwater shock waves generated by the explosion of 100mg PETN pellets in a chamber at shock over-pressures ranging up to 44MPa. Pressure histories were measured simultaneously on 113 samples. We found that bottom dwellers were distinctively killed against overpressures of 12MPa and this value is much higher than the usual shock over-pressure threshold value for marine-creatures having lungs and balloons.     

A SYNTHETIC ROUTE TO 3-METHYLTHIO-2-ALKANONES STARTING FROM 3-ALKYL-2,4-PENTANEDIONES

Abstract

An efficient preparation of a 3-methylthio-2-alkanone (1) has been realized by the reaction of a 3-alkyl-2,4-pentanedione (8) with one mol-equiv of S-methyl methanethiosulfonate (4) in the presence of excess EtONa in EtOH. Furthermore, treatment of 8 with 4 and K₂CO₃ in refluxing acetone, followed by addition of MeOH and heating the resulting mixture, gave 1 in a high yield. These methods were applied to synthesis of pseudoionone.     

Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.     

Theoretical analysis of correlation between ionization threshold fluence in IR‐MALDI and IR absorption spectrum of matrix molecules

To investigate the correlation between the wavelength dependence of ionization threshold fluence of target molecule in matrix‐assisted laser desorption/ionization by infrared (IR) laser and the IR absorption spectrum of matrix molecule, we have analyzed the IR absorption spectra of four matrix molecules using density functional theory and correlated ab initio molecular orbital method. The calculated IR absorption spectra of the isolated molecules showed more qualitative correlation with the wavelength dependence of ionization threshold fluence than those of the solid state structures. We can consider that a portion of matrix molecules lost the ordered crystal structure and that the transition to the diluted or isolated state occurred at the early process of IR laser irradiation. © 2012 Wiley Periodicals, Inc.     

Concentration dependences of dielectric properties at 105 Hz and 106 Hz for aqueous solutions of hydroxypropyl cellulose

The concentration dependences of dielectric properties measured at 10⁵ Hz and 10⁶ Hz are reported for aqueous solutions of hydroxypropyl cellulose. Phase behaviour of the solutions was also observed with a polarizing optical microscope. For solutions with concentrations well above 40 wt %, polydomain textures, including the banded texture, were observed after a prehistory of deformation. No significant discontinuous changes in the dielectric constant, ε_r′, and loss factor, ε_r″, were found at the concentrations around the onset of the isotropic–cholesteric phase transition and in the biphasic region. In contrast, the steeper changes in ε_r′ and ε_r″ were found at the critical concentration for the fully developed cholesteric phase transition with the polydomain textures.     

Accurate measurement of uranium isotope ratios in soil samples using thermal ionization mass spectrometry equipped with a warp energy filter

A chemical and mass-spectrometric procedure for uranium isotopic analysis using a thermal ionisation mass spectrometer equipped with a Wide Aperture Retardation Potential energy filter has been developed and applied to uranium isotopic measurements for various soil samples. Soil samples were digested using a microwave digestor. Uranium was isolated from soil samples by the chemical separation procedure based on the use of anion-exchange resin and UTEVA extraction chromatography column. The isotope ratios were measured for two certified reference materials by using a VG Sector 54-30 thermal ionisation mass spectrometer in dynamic mode with Faraday cup and Daly ion counting system. Replicates of standard reference materials showed excellent analytical agreement with established values supporting the reliability and accuracy of the method. Precision of the ²³⁵U/²³⁸U ratio was achieved by a correction factor of 0.22% amu as a function of ion-beam intensity with sample loads of around 250?ng of U. The resulting reproducibility for standards and soil samples was better than 0.2% at two standard deviations (SD). Uranium isotopic compositions have been determined in several reference soil samples such as Buffalo river sediment, NIST 2704, river sediment SRM 4350b and ocean sediment NIST-4357 and a Chernobyl soil sample. There was a significant deviation from the natural uranium in comparison with Chernobyl soil samples.