Optical current transducers using flint glass fiber as the faraday sensor element

This paper describes development of the optical current transducers using flint glass fiber as the Faraday effect sensing element. Excellent polarization properties of the fiber with low birefringence are described, and the design and test data of a current transducer using the fiber manufactured for use in electric power facilities are reviewed. Experimental results on flexible characteristics of a scheme with round trip light transmission in the fiber is also reported.     

Measurement of non-DLVO force on a silicon substrate coated with ammonium poly(acrylic acid) using scanning probe microscopy

The repulsive force originating from steric hindrance of polymers in aqueous solvent was investigated using scanning probe microscopy (SPM). The contact angle (CA) of ammonium poly(acrylic acid) (PAA) solution on the Si surface was measured to estimate the state of the Si substrate. Results of CA measurement show that the Si surface was fully covered with PAA at 0.1 mass% in aqueous solution. The interaction force between the Si tip and the wafer was estimated using the SPM force curve mode. The force curve measured in the ion-exchanged purified water showed the typical relation predicted by Derjaguin-Landau-Verway-Overbeek (DLVO) theory. However, the force curve shape in the 0.1 mass% PAA solution was significantly different. Only a repulsive force was observed at less than about 4 nm of separation distance between the Si wafer and cantilever tip. This distance originated from the steric repulsions of PAA adsorbed onto the Si wafer and cantilever tip.     

Purcell effect of GaAs quantum dots by photonic crystal microcavities

We fabricate photonic crystal slab microcavities embedded with GaAs quantum dots by electron beam lithography and droplet epitaxy. The Purcell effect of exciton emission of the quantum dots is confirmed by the micro photoluminescence measurement. The resonance wavelengths, widths, and polarization are consistent with numerical simulation results.     

Investigation of the influence of cell density of human fibroblasts cryopreserved inside collagen sponges at various cooling rates

The influence of cell density of cells cryopreserved inside a collagen matrix at various cooling rates was investigated. Human fibroblasts were three-dimensionally cultured for 2 days in a collagen sponge (20 mm in diameter and 1 mm in thickness) as an extracellular matrix to imitate biological tissue (artificial tissue). Different cell densities for the artificial tissue were used, from 10(5) to 10(7) cells/cm(3). Four artificial tissues were first stacked in a test chamber, frozen at a cooling rate of 0.3 to 50 degrees C/min in a solution of Dulbecco's Modified Eagle Medium, 20% fetal bovine serum and 10% dimethylsulfoxide, kept frozen below -185 degrees C for 2 hours, and then finally thawed. Membrane integrity of fibroblasts using a trypan blue exclusion assay was evaluated as an index for post-thaw cellular viability. Results show that with increasing cell density, the post-thaw membrane integrity decreased. Therefore, in the cryopreservation of biological tissue, it seems high cell density is one factor which causes a decline in viability.     

Electrochemical properties of thin TiO2 electrode on Li1 + xAlxGe2 − x(PO4)3 solid electrolyte

A fabrication of all-solid-state thin-film rechargeable lithium ion batteries by sol-gel method is expected to achieve both the simplification and cost reduction for fabrication process. TiO₂ thin film electrode was prepared by PVP (polyvinylpyrrolidone) sol-gel method combined with spin-coating on Li_1 + xAl_xGe_2 − x(PO₄)₃ (LAGP) solid electrolyte which has wide electrochemical window. The thin film was composed of anatase TiO₂ that is the most active phase for Li insertion and extraction and contacted well with LAGP substrate. In the cyclic voltammogram, a redox couple was observed at 1.8 V vs. Li/Li⁺ assigned to Li insertion/extraction into/from anatase TiO₂, indicating that the thin film worked as electrode for lithium battery. The charge and discharge test in various charge and discharge rates revealed that the discharge process (delithiation) is thought to be faster than charge process (lithiation). It is attested that the sol-gel process, which derives both simplification and cost reduction for fabrication process, can be applied to thin film battery using LAGP solid electrolyte.     

Sharp photonic Crystal Defect Modes and Their Response to Ultrashort Optical Pulses

Single photonic crystal defects based on an air-bridge structure were fabricated. We obtained sharp defect modes with quality factors higher than 600 and observed their response to ultrashort optical pulses by utilizing two-photon absorption.     

Depth-adaptive regularized reconstruction for reflection diffuse optical tomography

We study reflection diffuse optical tomography using two-dimensional (2D) continuous-wave source-detector arrays on the surface of semi-infinite medium, aiming at imaging the perfusion and the hemoglobin oxygen saturation variation of human cerebral cortex with brain activation. We had previously formulated the inverse problem with Moore-Penrose inversion. When we use simple regularization in this inverse problem, the reconstruction sensitivity decreases markedly with the depth so that the signal in the deep range may be masked by an unwanted signal in the shallow range. In this paper, we propose a depth-adaptive regularized reconstruction, in which we assign a smaller regularization parameter with the depth. We demonstrate improvement of the three-dimensional (3D) reconstruction uniformity using the proposed scheme.     

Nanoparticles in Emissions and Atmospheric Environment: Now and Future

Journal of Nanoparticle Research -     

Focal length measurement of a varifocal liquid lens with capacitance detection

This paper reports on a detailed deformation model of varifocal liquid lenses fabricated by Parylene-on-liquid-deposition (POLD), which can be applied to measure and adjust the focal length of such lenses without using extra sensors or sensing mechanisms. The lens was fabricated by encapsulating a liquid between a transparent electrode and a polymer film that was covered with a metal electrode. When voltage is applied to the two electrodes, the lens deforms due to the electrostatic force, and its focal length and the capacitance between the two electrodes change simultaneously. This characteristic enables the focal length of the lens to be adjusted and detected by measuring the capacitance change. The focal length of the fabricated varifocal liquid lens changed from 153.6 to 82.6 mm by applying 150-V. The focal length change of the liquid lens was calculated from the change in its capacitance. Finally, to confirm the efficiency of this varifocal liquid lens, we fabricated a confocal distance sensor using the lens for laser scanning and demonstrated that this system can be used to measure distances of 94–140 mm with an average error of 0.83 mm and a standard deviation of 0.77 mm.     

Observation of THz coherent transition radiation from single-bunch beam at KURRI-LINAC as an intense pulsed light source

A single-bunch beam has been generated using a developed high-speed avalanche-type pulser in KURRI-LINAC in order to lift restrictions of the spectral resolution in the spectroscopic study and the delay time in the time-resolved measurement. Both of the rise and fall times of the developed pulser are 110 ps. The observation of CTR has confirmed the single-bunch beam. The degree of impurity of single bunch has been estimated to be 1.5% by the analysis of the interferogram.