High power single-frequency continuous-wave Nd:YVO4 master-oscillator power amplifier

We report a highly-efficient, high-power, single-frequency Nd:YVO₄ master-oscillator power-amplifier with near-diffraction-limited output beam quality. A diode-pumped Nd:YVO₄ ring laser incorporating a passive method for suppressing axial-mode-hopping was employed as the master-oscillator, and was amplified by a three-stage diode-end-pumped Nd:YVO₄ amplifier, yielding 79 W of output with an extraction efficiency of 29%. The overall power gain was 15 dB for an input power from the master-oscillator of 2.4 W, and the M² parameter was less than 1.5 at the maximum power. The prospects for a further increase of power and brightness via this approach are considered. PACS 42.55.Xi; 42.60.Da; 42.60.Jf     

The effect of surface crystalline layers on asymmetric off-diagonal magnetoimpedance in field-annealed CoFeSiB amorphous ribbons

The off-diagonal magnetoimpedance in field-annealed CoFeSiB amorphous ribbons was measured using a pick-up coil wound around the sample. One side of a ribbon was etched in hydrofluoric acid solution during various times in order to change the thickness of the surface crystalline layer appearing after annealing. The asymmetric two-peak field dependence of the off-diagonal impedance was observed for all samples. The evolution of the off-diagonal magnetoimpedance with the change in the ribbon thickness is analyzed.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

A Reverse of bessel’s inequality in 2-inner product spaces and some grüss type related results with applications

A reverse of Bessel’s inequality in 2-inner product spaces and companions of Grüss inequality with applications for determinantal integral inequalities are given.     

Photoemission studies of oxygen adsorbed on a LiAl(1 1 0) alloy surface: Role of Li segregation

We investigated that the effect of the number of segregated Li atoms on the rate of oxidation on a LiAl alloy surface. Oxygen molecules adsorbed on the LiAl alloy react with the surface atoms to form stable oxides. The segregated Li atoms at reconstructed surfaces (c(2×2) and (2×1)) enhance the oxidation rate and form stable LiAlO_x and Li₂O. The degree of enhancement of oxidation by segregated Li atoms varies as a function of O₂ exposure and annealing temperature, where the latter is directly related to the mode of surface reconstruction by Li segregation.     

Dielectrophoretically aligned GaN nanowire rectifiers

We demonstrate GaN nanowire (NW) current rectifiers which were formed by assembling n-GaN nanowires on a patterned p-Si substrate by means of alternating current (ac) dielectrophoresis. The dielectrophoresis was accomplished at a frequency of 10 kHz with three different ac bias voltages (5, 10, and 15 V_p–p), indicating that the number of aligned GaN nanowires increased with increasing ac bias voltage. The n-GaN NW/p-Si diodes showed well-defined current rectifying behavior with a forward voltage drop of 1.2–1.5 V at a current density of 200 A/cm². We observed that the GaN NW diode functioned well as a half-wave rectifier. PACS 71.20.Nr; 73.40.Cg; 73.40.Ei; 73.40.Kp     

Preparation of antimicrobial poly(vinyl alcohol) nanofibers containing silver nanoparticles

Polyvinyl alcohol (PVA) nanofibers containing Ag nanoparticles were prepared by electrospinning PVA/silver nitrate (AgNO₃) aqueous solutions, followed by short heat treatment, and their antimicrobial activity was investigated for wound dressing applications. Since PVA is a water soluble and biocompatible polymer, it is one of the best materials for the preparation of wound dressing nanofibers. After heat treatment at 155 °C for 3 min, the PVA/AgNO₃ nanofibers became insoluble, while the Ag⁺ ions therein were reduced so as to produce a large number of Ag nanoparticles situated preferentially on their surface. The residual Ag⁺ ions were reduced by subsequent UV irradiation for 3 h. The average diameter of the Ag nanoparticles after the heat treatment was 5.9 nm and this value increased slightly to 6.3 nm after UV irradiation. It was found that most of the Ag⁺ ions were reduced by the simple heat treatment. The PVA nanofibers containing Ag nanoparticles showed very strong antimicrobial activity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2468–2474, 2006     

Probing antiferromagnetic order with heat capacity in exchange-biased structures

We explore the magnetic heat capacity in exchange-biased ferromagnet/antiferromagnet bilayers theoretically. We show that changes in the antiferromagnetic structure due to the reversal of the ferromagnet layer can be detected by distinct features in the heat capacity. This offers a method for probing antiferromagnetic domains in exchange-biased systems.     

Design and Experimental Characterization of Low‐Volume PM10/2.5/1.0 Trichotomous Sampler Inlet

This paper presents the development and laboratory evaluation of a PM10/2.5/1.0 trichotomous sampling inlet that consists of two main parts: a previously designed PM10 size‐selective inlet part and a PM2.5/1.0 two‐stage virtual impactor, which was newly fabricated and attached serially to the PM10 size selective inlet part. Particles are collected in three locations through the trichotomous sampling inlet to provide for not only particle concentration measurements of PM10, PM2.5 and PM1.0, but also those of PM2.5–10 and PM1.0–2.5.     

A Lagrangean heuristic algorithm for disassembly scheduling with capacity constraints

This paper considers the problem of determining the disassembly schedule (quantity and timing) of products in order to satisfy the demand of their parts or components over a finite planning horizon. The objective is to minimize the sum of set-up, disassembly operation, and inventory holding costs. As an extension of the uncapacitated versions of the problem, we consider the resource capacity restrictions over the planning horizon. An integer program is suggested to describe the problem mathematically, and to solve the problem, a heuristic is developed using a Lagrangean relaxation technique together with a method to find a good feasible solution while considering the trade-offs among different costs. The effectiveness of the algorithm is tested on a number of randomly generated problems and the test results show that the heuristic suggested in this paper can give near optimal solutions within a short amount of computation time.