Characterization of an all Sol-Gel Electrochromic Device WO3/Ormolyte/CeO2-TiO2

Electrochemical lithium intercalation in thin films of CeO₂-TiO₂ and WO₃, prepared by the sol-gel technique was investigated with cyclic voltammetry and spectroelectrochemical techniques in propylene carbonate solutions. A solid state system having the configuration WO₃/Ormolyte/CeO₂-TiO₂ has been assembled. The solid electrolyte, an organically modified electrolyte (ormolyte), was prepared with different [O]/[Li] ratios. The transmittance variation of this system during a potentiostatic step from –0.7 V to 0.8 V was about 35% at 550 nm.     

Isolation of Indonesian cananga oil using multi-cycle pressure drop process

New process, instantaneous controlled pressure drop (DIC) was applied on Cananga odorata dry flowers with the aim to isolate essential oil. DIC is based on high temperature, short time heating followed by an abrupt pressure drop into a vacuum. A part of volatile compounds is carried away from flowers in the form of vapor (DIC direct oil) that evolves adiabatically during the pressure drop (proper isolation process) and the other part remains in the DIC-treated flowers (DIC residual oil). In the present paper, the effect of DIC cycle number (1-9) and heating time (4.3-15.7 min) on the availability of oil compounds was investigated at three levels of steam pressure (0.28, 0.4 and 0.6 MPa). The availability was defined as the amount of a compound in direct or residual oil divided by the amount of this compound in the reference oil extracted from non-treated flowers by chloroform during 2h. The total availability and yield of volatiles in the direct oil increased with pressure and cycle number. At a higher pressure, the effect of heating time was insignificant. The amount of oxygenated monoterpenes and other light oxygenated compounds (i.e. predominantly exogenous compounds) in the residual flowers was lower than in the direct oil and this amount decreased with cycle number. On the other hand, the availability of oxygenated sesquiterpenes and other heavy oxygenated compounds (i.e. predominantly endogenous compounds) in residual flowers exhibited a maximum for about five cycles and their quantity at this point was three times as much as in the direct oil. The total availability of each compound at 0.6 MPa was higher than one. The rapid DIC process (0.6 MPa, 8 cycles, 6 min) gave better results than steam distillation (16 h) concerning direct oil yield (2.8%dm versus 2.5%dm) and content of oxygenated compounds (72.5% versus 61.7%).     

Molecular assemblies from imidazolyl-containing haloalkenes and haloalkynes: competition between halogen and hydrogen bonding

The structural characterization of molecular assemblies constructed from imidazolyl-containing haloalkenes and haloalkynes is reported. 1-(3-Iodopropargyl)imidazole (2) and 1-(2,3,3-triiodoallyl)imidazole (5) were synthesized from 1-propargylimidazole (1). In the solid state, these wholly organic modules self-assemble through N...I halogen-bonding interactions, thus giving rise to polymeric chains. The N...I interaction observed in 2 (d(N...I)=2.717 A, angle-spherical C(sp)-I...N=175.8 degrees) is quite strong relative to previously reported data. The N...I interaction in 5 (d(N...I)=2.901 A, angle-spherical C(sp2)-I...N=173.6 degrees) is weaker, in accordance with the order C(sp)-X<--base>C(sp2)-X<--base. Compound 5 was found to give a 1:1 cocrystal 4 with morpholinium iodide (6). In the X-ray crystal studies of 4, N...I halogen-bonding interactions similar to those observed in 5 were shown not to be present, as the arrangement of the molecules is governed by two interwoven hydrogen-bonding networks. The first network involves N-H...O interactions between nearby morpholinium cations, and the second network is based on N-H...N hydrogen bonding between morpholinium cations and imidazolyl groups. Both hydrogen-bonding schemes are charge-assisted. Halogen bonding is not completely wiped out, however, as the triiodoalkene fragment forms a halogen bond with an iodide anion in its vicinity (d(I...I)=3.470 A, angle-spherical C(sp2)-I...I=170.7 degrees). X-ray crystal studies of 6 show a completely different arrangement from that observed in 4, namely, N-H...O interactions are not present. In crystalline 6, morpholinium cations are interconnected through C-H...O bridges (d(H...O)=2.521 and 2.676 A), and the NH2+ groups interact with nearby iodide anions (d(H...I)=2.633 and 2.698 A).     

Cu-Doped ZnO Nanoparticles for Non-Enzymatic Glucose Sensing

Copper-doped zinc oxide nanoparticles (NPs) Cu_xZn_1−xO (x = 0, 0.01, 0.02, 0.03, and 0.04) were synthesized via a sol-gel process and used as an active electrode material to fabricate a non-enzymatic electrochemical sensor for the detection of glucose. Their structure, composition, and chemical properties were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infrared (FTIR) and Raman spectroscopies, and zeta potential measurements. The electrochemical characterization of the sensors was studied using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV). Cu doping was shown to improve the electrocatalytic activity for the oxidation of glucose, which resulted from the accelerated electron transfer and greatly improved electrochemical conductivity. The experimental conditions for the detection of glucose were optimized: a linear dependence between the glucose concentration and current intensity was established in the range from 1 nM to 100 μM with a limit of detection of 0.7 nM. The proposed sensor exhibited high selectivity for glucose in the presence of various interfering species. The developed sensor was also successfully tested for the detection of glucose in human serum samples.     

Solid-phase extraction clean-up procedure for the analysis of PAHs in lichens

A clean-up procedure based on a solid-phase extraction column was optimized for determination of polycyclic aromatic hydrocarbons (PAHs) in lichen extracts to remove co-extracted compounds from the matrix in the final extract. Several kinds of solid phases were evaluated: normal phase (-NH₂ and alumina), strong anion exchange and reversed phase. The -NH₂ columns were the most effective by using a packed solid bed of 500?mg. The lichen raw extract was loaded on the column previously conditioned with dichloromethane and hexane. Hexane (0.5?mL) was used as rinsing solvent, and PAHs were quantitatively eluted (80–97%) using 2?mL of hexane–dichloromethane (65–35) as eluting solvent. In these conditions, even the heaviest PAHs were quantitatively eluted. The optimized SPE method provides a short time and low-solvent-consumption sample clean-up compared with other conventional methods based on column chromatography. The analytical procedure, dynamic sonication-assisted extraction, followed by the optimized solid-phase extraction clean-up, was used to determine the 16 EPA priority PAHs from native lichens collected from the Aragon valley in central Pyrenees. The PAH concentrations in lichen samples ranged from 352 to 1654?ng?g^?1, and the minimum concentration value was established as the regional reference PAH levels in the area.     

Ab Initio Study of Structures,Metallotropic 1,2-Shifts and Prototropic 1,2-Shifts of Cyclopentadienyl(trimethyl)silane, -germane and -stannane

Molecular structures, metallotropic and prototropic shifts of cyclopentadienyl(trimethyl)silane ( 1 ), cyclopentadienyl(trimethyl)germane ( 2 ), and cyclopentadienyl(trimethyl)stannane ( 3 ) were investigated using ab initio molecular orbital and the Becke, Lee, Yang, and Parr density functional (B3LYP) methods. The results show that the most stable structure of compounds 1-3 has the (CH 3 ) 3 M fragment in the allylic position. The energy barrier of metallotropic shifts in compound 1 is higher than in 2 , and in compound 2 higher than in 3 , in good agreement with experimental data. The cyclopentadienyl rings in compounds 1-3 are found to be planar but this result contradicts the reported experimental data.     

High‐throughput characterization of pattern formation in symmetric diblock copolymer films

Surface‐pattern formation in thin block copolymer films was investigated by utilizing a high‐throughput methodology to validate the combinatorial measurement approach and to demonstrate the value of the combinatorial method for scientific investigation. We constructed measurement libraries from images of subregions of block copolymer films having gradients in film thickness and a range of molecular mass, M. A single gradient film covers a wide range of film morphologies and contains information equivalent to a large number of measurements of films having a fixed thickness, h. Notably, the scale of the surface patterns is generally much larger than the molecular dimensions so that the interpretation of the patterns is more subtle than ordering in bulk block copolymer materials, and there is no predictive theory of this type of surface‐pattern formation. We observed a succession of surface patterns that repeat across the film with increasing h [extended smooth regions, regions containing circular islands, labyrinthine (“spinodal”) patterns, holes, and smooth regions again]. The extended smooth regions and the labyrinthine patterns appear to be novel features revealed by our combinatorial study, and these patterns occurred as bands of h that were quantized by integral multiples of the bulk lamellar period, L_o. The magnitude of the height gradient influenced the width of the bands, and the smooth regions occupied an increasing fraction of the film‐surface area with an increasing film gradient. The average size of the spinodal patterns, λ, was found to scale as λ ～ L or λ ～ M^?1.65 and reached a limiting size at long annealing times. The hole and island features had a size comparable to λ, and their size likewise decreased with increasing M. The smooth regions were attributed to an increase in the surface‐chain density in the outer brushlike block copolymer layer with increasing h, and the scaling of λ with M was interpreted in terms of the increasing surface elasticity with M. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2141–2158, 2001     

Volatile constituents of two Hypericum species from Tunisia

The chemical composition of the essential oils obtained by hydrodistillation from the aerial parts of the Tunisian Hypericum perforatum and H. ericoides ssp. roberti was elucidated by a combination of GC and GC-MS analyses. The main constituents of the oil of H. perforatum were alpha-pinene (11.8%), alpha-ylangene (10.4%), germacrene-D (9.5%), n-octane (6.5%) and alpha-selinene (5.9%). The oil of H. ericoides ssp. roberti exhibited a higher amount of aliphatic and branched hydrocarbons and the main constituents were n-octane (29.1%), alpha-pinene (10.9%), pulegone (7.7%) and acetophenone (7%). Both qualitative and quantitative differences were observed between the studied oils. This chemical variability seems likely to result from the genetic variability, since samples of both species were collected at the same location and processed under the same conditions.     

Determination of neutron flux parameters in PUSPATI TRIGA Mark II Research Reactor, Malaysia

In standardization NAA, it is necessary to characterize the neutron spectrum parameters such as epithermal neutron flux shape factor (α), thermal to epithermal neutron flux ratio (f), thermal neutron flux (φ _th) and epithermal neutron flux (φ _epi) in the irradiation facility to determine the concentration of an element in the sample using absolute and k ₀ standardization methods. The α and f were determined using Cd-ratio multi monitor method using experimental data obtained in PUSPATI TRIGA Mark II research reactor at four irradiation positions (10, 20, 30 and 40) of the rotary rack. The calculated values of α and f ranged from 0.006 to 0.0281 and 18.56 to 19.12 respectively. The average values of φ _th and φ _epi were found as 2.33 × 10¹² and 1.23 × 10¹¹ n cm^?2 s^?1 respectively. Moreover, a comparison of the neutron flux parameters in the present study shows an acceptable level of consistency with those of previous studies.