19.4%‐efficient large‐area fully screen‐printed silicon solar cells

We demonstrate industrially feasible large‐area solar cells with passivated homogeneous emitter and rear achieving energy conversion efficiencies of up to 19.4% on 125 × 125 mm² p‐type 2–3 Ω cm boron‐doped Czochralski silicon wafers. Front and rear metal contacts are fabricated by screen‐printing of silver and aluminum paste and firing in a conventional belt furnace. We implement two different dielectric rear surface passivation stacks: (i) a thermally grown silicon dioxide/silicon nitride stack and (ii) an atomic‐layer‐deposited aluminum oxide/silicon nitride stack. The dielectrics at the rear result in a decreased surface recombination velocity of S_rear = 70 cm/s and 80 cm/s, and an increased internal IR reflectance of up to 91% corresponding to an improved J_sc of up to 38.9 mA/cm² and V_oc of up to 664 mV. We observe an increase in cell efficiency of 0.8% absolute for the cells compared to 18.6% efficient reference solar cells featuring a full‐area aluminum back surface field. To our knowledge, the energy conversion efficiency of 19.4% is the best value reported so far for large area screen‐printed solar cells. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Laser power noise detection at the quantum-noise limit of 32 A photocurrent

The power noise of a cw Nd:YAG laser system was measured at radio frequencies using the optical ac coupling technique. An additional mode cleaner in the setup allowed a high optical ac coupling amplification of 62.3. For the first time, to our knowledge, a sensitivity of 1.1×10?1? Hz(-1/2) relative power noise was achieved corresponding to an equivalent detected photocurrent of 32 A. High precision optics experiments can utilize this scheme to improve the sensitivity of their photodetectors.     

Laboratory Flow Experiments for Visualizing Carbon Dioxide-Induced,Density-Driven Brine Convection

Injection of carbon dioxide (CO₂) into saline aquifers confined by low- permeability cap rock will result in a layer of CO₂ overlying the brine. Dissolution of CO₂ into the brine increases the brine density, resulting in an unstable situation in which more-dense brine overlies less-dense brine. This gravitational instability could give rise to density-driven convection of the fluid, which is a favorable process of practical interest for CO₂ storage security because it accelerates the transfer of buoyant CO₂ into the aqueous phase, where it is no longer subject to an upward buoyant drive. Laboratory flow visualization tests in transparent Hele-Shaw cells have been performed to elucidate the processes and rates of this CO₂ solute-driven convection (CSC). Upon introduction of CO₂ into the system, a layer of CO₂-laden brine forms at the CO₂-water interface. Subsequently, small convective fingers form, which coalesce, broaden, and penetrate into the test cell. Images and time-series data of finger lengths and wavelengths are presented. Observed CO₂ uptake of the convection system indicates that the CO₂ dissolution rate is approximately constant for each test and is far greater than expected for a diffusion-only scenario. Numerical simulations of our system show good agreement with the experiments for onset time of convection and advancement of convective fingers. There are differences as well, the most prominent being the absence of cell-scale convection in the numerical simulations. This cell-scale convection observed in the experiments may be an artifact of a small temperature gradient induced by the cell illumination.     

Embedded constant mean curvature surfaces with special symmetry

We give sharp, necessary conditions on complete embedded CMC surfaces with three ends and an extra reflection symmetry. The respective submoduli space is a two-dimensional variety in the moduli space of general CMC surfaces. Fundamental domains of our CMC surfaces are characterized by associated great circle polygons in the three-sphere. Received: 23 January 1998 / Revised version: 23 October 1998     

Laboratoriumsapparate

Ohne Zusammenfassung     

Gas Flow in Porous Media With Klinkenberg Effects

Gas flow in porous media differs from liquid flow because of the large gas compressibility and pressure-dependent effective permeability. The latter effect, named after Klinkenberg, may have significant impact on gas flow behavior, especially in low permeability media, but it has been ignored in most of the previous studies because of the mathematical difficulty in handling the additional nonlinear term in the gas flow governing equation. This paper presents a set of new analytical solutions developed for analyzing steady-state and transient gas flow through porous media including Klinkenberg effects. The analytical solutions are obtained using a new form of gas flow governing equation that incorporates the Klinkenberg effect. Additional analytical solutions for one-, two- and three-dimensional gas flow in porous media could be readily derived by the following solution procedures in this paper. Furthermore, the validity of the conventional assumption used for linearizing the gas flow equation has been examined. A generally applicable procedure has been developed for accurate evaluation of the analytical solutions which use a linearized diffusivity for transient gas flow. As application examples, the new analytical solutions have been used to verify numerical solutions, and to design new laboratory and field testing techniques to determine the Klinkenberg parameters. The proposed laboratory analysis method is also used to analyze data from steady-state flow tests of three core plugs from The Geysers geothermal field. We show that this new approach and the traditional method of Klinkenberg yield similar results of Klinkenberg constants for the laboratory tests; however, the new method allows one to analyze data from both transient and steady-state tests in various flow geometries.     

Two CdII/CoII‐Imidazolate Coordination Polymers: Syntheses,Crystal Structures,Stabilities, and Luminescent/Magnetic Properties

Cadmium(II) based 2D coordination polymer [Cd(L1)₂(DMF)₂] ( 1 ) (L1 = 4,5‐dicyano‐2‐methylimidazolate, DMF = N,N′‐dimethylformamide) and 2D cobalt(II)‐imidazolate framework [Co(L3)₄] ( 2 ) (L3 = 4,5‐diamide‐2‐ethoxyimidazolate) were synthesized under solvothermal reaction conditions. The materials were characterized by elemental analysis, IR spectroscopy, thermogravimetric analysis, powder X‐ray diffraction measurement (PXRD) and single‐crystal X‐ray diffraction. Compound 1 has hexacoordinate Cd^II ions and forms a zigzag chain‐like coordination polymer structure, whereas compound 2 exhibits a 2D square grid type structure. The thermal stability analysis reveals that 2 showed an exceptional thermal stability up to 360 °C. Also, 2 maintained its fully crystalline integrity in boiling water as confirmed by PXRD. The solid state luminescent property of 1 was not observed at room temperature. Compound 2 showed an independent high spin central Co^II atom.