Development of a wide range-operable,rich-lean low-NOx combustor for NH3 fuel gas-turbine power generation

Low-NOx NH₃-air combustion power generation technology was developed by using a 50-kWe class micro gas-turbine system at the National Institute of Advanced Industrial Science and Technology (AIST), Japan, for the first time. Based on the global demand for carbon-free power generation as well as recent advances involving gas-turbine technologies, such as heat-regenerative cycles, rapid fuel mixing using strong swirling flows, and two-stage combustion with equivalence ratio control, we developed a low-NOx NH₃-air non-premixed combustor for the gas-turbine system. Considering a previously performed numerical analysis, which proved that the NO reduction level depends on the equivalence ratio of the primary combustion zone in a NH₃-air swirl burner, an experimental study using a combustor test rig was carried out. Results showed that eliminating air flow through primary dilution holes moves the point of the lowest NO emissions to the lesser fuel flow rate. Based on findings derived by using a test rig, a rich-lean low NOx combustor was newly manufactured for actual gas-turbine operations. As a result, the NH₃ single fueled low-NOx combustion gas-turbine power generation using the rich-lean combustion concept succeeded over a wide range of power and rotational speeds, i.e., below 10–40 kWe and 75,000–80,000?rpm, respectively. The NO emissions were reduced to 337?ppm (16% O₂), which was about one-third of that of the base system. Simultaneously, unburnt NH₃ was reduced significantly, especially at the low electrical power output, which was indicative of the wider operating range with high combustion efficiency. In addition, N₂O emissions, which have a large Global Warming Potential (GWP) of 298, were reduced significantly, thus demonstrating the potential of NH₃ gas-turbine power generation with low environmental impacts.     

Visualization of Magnetization Transfer Effect in Polyethylene Glycol Impregnated Waterlogged Wood

To visualize the condition of impregnation of polyethylene glycol (PEG) in waterlogged wood, we demonstrated magnetic transfer (MT) magnetic resonance imaging (MRI) through a series of process of PEG impregnation. Three different samples were examined; reference wood, 10 cm cut wood, and 5 cm cut wood. During this study, the upper section sample was kept immersed in water, for the middle and lower sections the concentration of PEG solution was changed at 20 wt% intervals from 20 to 100 wt%. The impregnated periods of each PEG solution concentration were 14 days. Then, MR imaging were performed with/without MT pulse. The MTR value for both 10 cm- and 5 cm-samples were shown to decrease at 20 wt% PEG at peak concentration. When the sample volume was large, e.g., 10 cm-sample, the MTR value decreased to 100 wt% PEG concentration. In contrast, when a sample volume was small, e.g., 5 cm-sample, MTR value decreased to 60 wt% PEG concentration. In conclusion, MTR analysis makes it possible to nondestructively visualize and evaluate the inner condition concerning the PEG impregnation method for waterlogged wood.     

Visualization of flow past a square prism with cut-corners at the front-edge

Flow past a square prism with cut-corners at the front-edge is numerically and experimentally visualized to investigate a mechanism of drag reduction. An adaptive numerical scheme based on the vortex method is implemented for two values of the Reynolds number between 200 and 1,250, and the results are compared with experiments. Experimental visualization techniques include the hydrogen-bubble technique atRe=4,000 and the oil-flow technique atRe=10,000 for a global wake formation, and the aluminum-flake technique for transient flow at the early stage of motion atRe=1,250. A similar reattachment flow pattern is shown in a wide range of the Reynolds number between 200 and 10,000, which implies a possibility of the drag reduction in the Reynolds number being approximately lower than 8,000 unlike the previous findings.     

Effect of calcination temperature on the microstructure of porous TiO<Subscript>2</Subscript> film

To obtain porous TiO₂ film, the precursor sol was prepared by hydrolysis of Ti isopropoxide and then complexed with trehalose dihydrate. The porous TiO₂ film was fabricated by the dip-coating technique on glass substrates using this solution. The TiO₂ film was calcined at 500 °C. The maximum thickness of the film from one-run dip-coating was ca. 740 nm. The film was composed of nanosized particle and pores. The porosity of the TiO₂ film was increased by addition of trehalose dihydrate to the sol. The porous TiO₂ films were calcined at different temperatures. The effects of calcination temperature on the microstructure of the porous TiO₂ film were investigated. The porous film prepared from sol containing trehalose still kept the porous structure after calcination at 950 °C. The phase transition temperature of the film from anatase to rutile was shifted from 650 to 700 °C by addition of trehalose to the sol.     

Statistical mixture design investigation of fractionated and total extracts from Erythrina speciosa Andrews leaves

The simplex centroid mixture design for the ethanol, dichloromethane, hexane and acetone solvents has been applied to the extraction of crude mass and the fiber, organic, neutral and basic fractions as well as the fractionation residues of Erythrina speciosa Andrews leaves. Binary and ternary synergic solvent interactions are seen to provide dominant contributions to the extraction of both crude mass and all the fractions. Quadratic and special cubic mixture models precisely predict the extracted quantities of each fraction and the residue as a function of the proportions of the four solvents. Different solvent mixtures are found to be the most efficient extractors for the different fractions: binary dichloromethane‐hexane mixtures for the fiber fraction, ternary ethanol‐dichloromethane‐acetone mixtures for the neutral fraction, binary ethanol‐dichloromethane mixtures for the organic fraction, crude extract and residue values and ternary ethanol‐dichloromethane‐hexane mixtures for the basic fraction. Principal component analysis shows that the ethanol‐dichloromethane mixtures are important for extracting large quantities of the basic and organic fractions as well as of the residue and crude masses.     

Synthesis of collagen-like sequential polypeptides containing O-phospho-L-hydroxyproline and preparation of electrospun composite fibers for possible dental application

A synthetic route is described for collagen-like polypeptides constructed from O-phospho-L-hydroxyproline [Hyp(PO(3)H(2))] residues. Using the synthetic polypeptides and a natural protein, gelatin, fine fibers and their network structures (ESNWs) were prepared via electrospinning. The composite ESNWs can induce the mineralization of calcium phosphate. The phosphoryl groups of the Hyp(PO(3)H(2)) residues affect both the crystalline phase and amount of the calcium phosphate, depending on the chemical structure in the repeating sequence. The composite ESNWs can be developed as a biocompatible replacement of the extracellular matrix of hard tissues, and thus can be applied as dental materials for restoration of dental cavities or as a sealant for pits and fissures.     

Effects of grafted polymer chains on lamellar membranes

We have investigated the effects of grafted polymer chains [poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide)] on the bending modulus and the intermembrane interactions of lamellar membranes (C(12)E(5) water) by means of a neutron spin-echo and a small-angle x-ray scattering technique. In this study the hydrophilic chain takes the mushroom configuration on the membrane. The bending modulus of the polymer-grafted membranes increases in proportion to the square of the end to end distance of the polymer chain, which agrees well with the theoretical prediction of Hiergeist and Lipowsky [J. Phys. II 6, 1465 (1996)]. From the interlamellar interaction point of view, the mushroom layer is renormalized to the membrane thickness, which enhances the repulsive Helfrich interaction. When the size of the decorated polymer chain increases to the interlamellar distance, however, the mushroom is squeezed so as to optimize the interlamellar potential. Further increase of the grafted polymer size brings a lamellar-lamellar phase separation, where the grafted polymer chains are localized in the dilute lamellar phase and the concentrated lamellar phase forms the onionlike texture.     

Capillary electrophoretic system incorporating an UV/CL dual detector

We developed a capillary electrophoretic system incorporating an ultra-violet absorption (UV)/chemiluminescence (CL) dual detector, taking advantage of the CL reaction of luminol-hydrogen peroxide and the batch-type CL detection cell. UV detection was carried out using the on-capillary method while CL detection was performed using the end-capillary method. Examination of isoluminol isothiocyanate (ILITC) as a model sample revealed two main peaks with UV detection and one main peak with CL detection. The first peak in the UV detection data corresponded to the main peak in the CL detection data. We then determined that the ILITC sample included natural ILITC as well as an impurity that had absorption behavior but did not have CL properties and labeling ability. Furthermore, the components of a mixture containing glycine, glycylglycine and glycylglycylglycine, all labeled with ILITC, were well separated and detected using the present system. The present system easily, rapidly, and simultaneously produces useful information due to the presence of both UV and CL detectors.     

Catalyst- and solvent-free click synthesis of cyclodextrin-based polyrotaxanes exploiting a nitrile N-oxide

A catalyst- and solvent-free synthesis of cyclodextrin-based polyrotaxanes exploiting a stable nitrile N-oxide as an end-capping agent was achieved. The C-C bond-forming end-capping reaction of an allyl-terminated pseudopolyrotaxane with the nitrile N-oxide proceeded smoothly by solid-state grinding in a mortar to afford a polyrotaxane.