互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

Ultrathin polymer film formation by collision-induced cross-linking of adsorbed organic molecules with hyperthermal protons

A new synthetic approach for the formation of ultrathin polymer films with customizable properties was developed. In this approach, the kinematic nature of proton collisions with simple organic molecules condensed on a substrate is exploited to break C-H bonds preferentially. The subsequent recombination of carbon radicals gives a cross-linked polymer thin film, and the selectivity of C-H cleavage preserves the chemical functionalities of the precursor molecules. The nature and validity of the method are exemplified with theoretical results from ab initio molecular dynamics calculations and experimental evidence from a variety of characterization techniques. Its applicability is demonstrated by the synthesis of ultrathin polymer films with precursor molecules such as dotriacontane, docosanoic acid, poly(acrylic acid) oligomer, and polyisoprene. The approach is fundamentally different from conventional chemical synthesis as it involves an unusual mix of physical and chemical processes including charge exchange, projectile penetration, kinematics, collision-induced dissociation, inelastic energy transfer, chain transfer, and chain cross-linking.     

Ni的掺入对复合氧化物LaFeO3的结构及性质的影响

合成子Ｎｉ替代铁酸稀土复合氧化物ＬａＦ３１－ｘＮｉｘＯ３（ｘ＝０．１－０．６），对样品进行了ＸＲＤ、ＩＲ及Ｍｏｓｓｂａｕｅｒ谱测试，结果表明：ｘ＝０＼１，０＼２，０＼３的样品为正交相，ｘ＝０．５，０．６的样品为菱方相；伴随相结构从正交向菱方结构的转变，ＩＲ谱上Ｆｅ（Ｎｉ）－Ｏ键伸振动谱带向高频移动近２０ｃｍ＾－１，Ｍｏｓｓｂａｕｅｒ谱测试表明Ｆｅ均处于＋３自旋态，Ｎｉ离子以＋３价进入晶格。     

Solid Phase Catalytic Oxidation of Alcohols by Polymer Supported Rare Earth Catalysts

Oxidation of alcohols to the corresponding aldehydes or ketones is one of the most fundamental reactions in organic chemistry [1,2]. Some of the products of the oxidation exhibit an important role in the organic synthesis as well as pharmaceutical synthesis. In most reactions, the lanthanide complexes show satisfied catalytic activities for some compounds. Furthermore, there has been increasing interest in the lanthanide complexes and several reports have appeared in the literature [3, 4]. But the exploitation of these complexes for the oxidation of some organic substrates has been limited. Here we reported a method for the preparation and the catalytic properties as well as the recycling of lanthanide complexes in oxidation of alcohols.The synthetic procedure for the polymer supported lanthanide complexes is shown as following(scheme 1):●-NH2+CICH2COOH(C2Hs)3N→●-NHCH2COOHM=Ce(Ⅲ), Tb(Ⅲ), Sm(Ⅲ)scheme 1The oxidation of benzyl alcohol was carried out in the presence of iodosylbenzene by the polymer supported Ce(Ⅲ), Tb(Ⅲ) and Sm(Ⅲ) catalysts at 80℃ for 4.0h, the yields of benz-aldehyde are as following (table 1):Table 1 Oxidation of benzyl alcohol with the supported catalysts**Reaction condition: benzyl alcohol 0.1 mmol, iodosylbenzene 0.15mmol,catalyst 0.2mg, 80℃ for 4.0h in 1,2-dichloroethane.It can be seen from the table that the Tb(Ⅲ) complex shows higher catalytic activity for the oxidation of benzyl alcohol. Further investigation is now being carded on to optimize the results.     

三段加热系统对大尺寸MPOF预制棒一步拉伸工艺

采用自行设计的微结构聚合物光纤专用拉丝系统对大尺寸微结构聚合物光纤预制棒的一步拉伸工艺进行了研究.该微结构聚合物光纤加热系统采用三段式梯度加热,可保持炉内温度的控制准确度在±2℃以内.在保持送料速度与牵引速度恒定、协调的条件下,通过对温度场温度梯度控制优化,确定了最佳拉丝温度组合,并得到了直径规格310 μm、标准偏差为±20 μm的较高质量的微结构聚合物光纤.     

新型菁类染料聚集体构筑和它的非线性光学特性研究

采用旋涂法制备了一种五甲川菁染料的超薄膜,利用原子力显微,椭偏仪、UV-Vis吸收光谱、红外光谱、小角X射线衍射等对薄膜的形貌和线性光谱性质进行了研究表征,结果表明染料在薄膜中形成了有序而稳定的J-聚集体,前向简并四波混频(DFWM)技术研究表明由于分子的聚集作用引起三阶非线性极化率的增大(χ(3)=2.55×10-12esu),利用激子耦合模型初步分析和讨论了产生非线性效应增强的内在机制。     

鲁氏毛霉发酵产物壳聚糖硫酸酯化的研究

利用鲁氏毛霉(Mucor rouxii)3.2545发酵产生壳聚糖,然后用氯磺酸/甲酰胺方法对壳聚糖进行硫酸酯化,当底物壳聚糖用量为1g时,其最佳反应条件为:10mL甲酰胺中氯磺酸添加量为3.0mL;反应温度为70℃;反应时间为3.Oh.其中反应温度对反应的影响最大.在最适反应条件下,壳聚糖硫酸酯的硫含量可以达到16.04%.通过红外光谱分析,发现壳聚糖已经成功地被硫酸酯化,而且结构与肝素相似.此外,所得产物还具有抗凝血和抗血栓的性质,其抗血栓的性质优于肝素.     

汽车车轮流场的数值模拟

首先以独立车轮为研究对象,以商用计算流体力学软件STAR—CD为工具,利用移动边界条件,并依据k-ε双方程高雷诺数湍流模型对三维定常不可压缩流N-S方程进行数值模拟计算．然后在合适尺寸的计算域下对3种不同宽度的静止和滚动车轮分别进行数值模拟计算,研究车轮宽度和来流速度对阻力系数的影响,将计算结果与实验结果进行了对比分析．计算结果表明,车轮宽度的减小以及来流速度的减小均明显降低汽车的气动阻力系数．     

甲醛的铂微粒修饰玻碳电极伏安法测定

采用电化学沉积法制备了铂微粒修饰玻碳电极(Pt/GCE).通过循环伏安法研究了甲醛在该电极上的电化学行为,并优化了实验参数,在此基础上建立了一种伏安法直接测定甲醛的方法.在酸性溶液中,甲醛的氧化峰电流与其浓度在1.0×10-5～1.0×10-3mol/L的范围内呈良好的线性关系(r=0.999 7),检出限为5.0 μmol/L,回收率为96%～104%,相对标准偏差为4.0%～4.5%.