Flow injection determination of bismuth in urine by successive retention of Bi(III) and tetrahydroborate(III) on an anion-exchange resin and hydride generation atomic absorption spectrometry

Bismuth as BiCl₄⁻ and BH₄⁻ ware successively retained in a column (150 mm × 4 mm, length × i.d.) packed with Amberlite IRA-410 (strong anion-exchange resin). This was followed by passage of an injected slug of hydrochloric acid resulting in bismuthine generation (BiH₃). BiH₃ was stripped from the eluent solution by the addition of a nitrogen flow and the bulk phases were separated in a gas–liquid separator. Finally, bismutine was atomized in a quartz tube for the subsequent detection of bismuth by atomic absorption spectrometry. Different halide complexes of bismuth (namely, BiBr₄⁻, BiI₄⁻ and BiCl₄⁻) were tested for its pre-concentration, being the chloride complexes which produced the best results. Therefore, a concentration of 0.3 mol l⁻¹ of HCl was added to the samples and calibration solutions. A linear response was obtained between the detection limit (3σ) of 0.225 and 80 μg l⁻¹. The R.S.D.% (n = 10) for a solution containing 50 μg l⁻¹ of Bi was 0.85%. The tolerance of the system to interferences was evaluated by investigating the effect of the following ions: Cu²⁺, Co²⁺, Ni²⁺, Fe³⁺, Cd²⁺, Pb²⁺, Hg²⁺, Zn²⁺, and Mg²⁺. The most severe depression was caused by Hg²⁺, which at 60 mg l⁻¹ caused a 5% depression on the signal. For the other cations, concentrations between 1000 and 10,000 mg l⁻¹ could be tolerated. The system was applied to the determination of Bi in urine of patients under therapy with bismuth subcitrate. The recovery of spikes of 5 and 50 μg l⁻¹ of Bi added to the samples prior to digestion with HNO₃ and H₂O₂ was in satisfactory ranges from 95.0 to 101.0%. The concentrations of bismuth found in six selected samples using this procedure were in good agreement with those obtained by an alternative technique (ETAAS). Finally, the concentration of Bi determined in urine before and after 3 days of treatment were 1.94 ± 1.26 and 9.02 ± 5.82 μg l⁻¹, respectively.     

Polycyclic aromatic hydrocarbons in the atmosphere: monitoring, sources, sinks and fate. II: Sinks and fate

This paper reviews the transformation processes that polycyclic aromatic hydrocarbons (PAHs) undergo in the atmosphere. These processes can take place both in the gas phase and in the particulate/aerosol one. Among the gas-phase processes, the most important ones are the daytime reaction with *OH and the nighttime reaction with *NO3. The relative importance of the two processes depends on the particular PAH molecule. For instance, gaseous naphthalene is mainly removed from the atmosphere upon reaction with *OH, while gaseous phenanthrene is mainly removed by reaction with *NO3. Oxy-, hydroxy-, and nitro-PAHs are the main transformation intermediates. Reaction with ozone and photolysis play a secondary role in the transformation of gaseous PAHs. The particle-associated processes are usually slower than the gas-phase ones, thus the gas-phase PAHs usually have shorter atmospheric lifetimes than those found on particulate. Due to the higher residence time on particulate when compared with the gas phase, direct or assisted photolysis plays a relevant role in the transformation of particle-associated PAHs. Among the other processes taking place in the condensed phase, nitration plays a very important role due to the health impact of nitro-PAHs, some of them being the most powerful mutagens found so far in atmospheric particulate extracts.     

Absolute line intensity measurements of hot bands for carbonyl sulfide at 12 microm

Using diode-laser spectroscopy, the intensities of 58 lines of the v(1) + v(1/2) - v(1/2) band and 36 lines of the 2v(1) - v(1) band of OCS have been measured. The corresponding band strengths S(0)(v) and the vibrational transition dipoles micro(v) have been derived through least squares fitting of these individual intensities. The band strengths values have been determined with a precision better than 2.5%.     

Ion chromatographic determination of iodide in urine and serum using a tubular ion-selective electrode based on a homogeneous crystalline membrane

The use of a laboratory-made iodide ion-selective electrode with tubular configuration and based on a crystalline membrane (AgI/Ag₂S) as the detector for ion chromatographic determination of iodide in urine and serum is described. A CIS reversed-phase column was coated withN-cetylpyridinium chloride to prepare a low-exchange-capacity analytical column and with hexadecyltrimethylammonium bromide to prepare a concentrator pre-column. A 2.0 ml min^–1 flow rate of deionized water and 0.1 mol 1^–1 KNO₃ solution was used for the pre-concentration and for the chromatographic separation, respectively. For optimum performance of the detector a background level of iodide was added into the column effluent. A linear relationship (r = 0.9997) between tubular electrode potential (as peak height) and iodide concentration in the range 5–400 g 1^–1 and a detection limit of 1.47 g 1^–1 were obtained. The method shows good reproducibility for both peak height (2.2% RSD) and retention time (1.3% RSD). Recoveries on its application to the samples were 93.0–100.9% for urine and 91.4–106.0% for serum.     

The synthesis and reactivity of the heptanuclear dianion [Os7(CO)20]2− including the synthesis and structural characterizations of the compounds [Os7(CO)20(AuPEt)3 2] and [Os8(CO)20(η6-C6H6]

Reduction of the heptaosmium cluster [Os₇(CO)₂₁] With [Et₄N][NH₄) gives the cluster dianion [Os₇(CO)₂₀]^2–,1, in high yield. The reaction of the dianion with [AuPR ₃Cl] (R=Et or Ph) in the presence of TlPF₆ forms [Os₇((CO)₂₀(AuPR ₃)₂] [R=Et (2a);R = Ph(2b)] in 80% yield, while the corresponding reaction with (Os(C₆H₆)(CH₃CN)₃]²⁺ gives [Os₈(CO)₂₀ ( ⁶-C₆H₆)] (3) in reasonable yield (ca. 30%). The dianion,1, and the clusters2 and3 have been fully characterized by bout spectroscopic and crystallographic methods. The crystal structure of the [Ph₄P]⁺ salt of1 shows that the metals in the anion adopt a capped octahedral geometry, with all twenty carbonyl ligands in terminal sites. The metal core geometry in2a is best described as a tricapped octahedron, and is based on the structure of the dianion1 with two adjacent octahedral faces capped by the Au atoms of the two AuPEt₃ groups. In a similar fashion, the geometry of3 is related to that of1 with the addition of an Os(C₆H₆) unit capped to a triangular face, to give a bicapped octahedral framework.     

Anion-pi interactions in cyanuric acids: a combined crystallographic and computational study

Several structures of pi complexes of isocyanuric acid and of several thio derivatives with anions have been computed by using high level ab initio calculations. The nature of the complexes has been studied by means of the method of molecular interaction potential with polarization (MIPp) and Bader's theory of atoms-in-molecules. These molecules form favorable complexes with anions and can be used as binding units for building receptors for the molecular recognition of anions. In several cases, the anion-pi interaction has been demonstrated experimentally by means of X-ray crystallography.     

Metal speciation dynamics in colloidal ligand dispersions

In this work we propose a dynamic metal speciation theory for colloidal systems in which the complexing ligands are localized on the surface of the particles; i.e., there is spatial heterogeneity of binding sites within the sample volume. The differences between the complex formation and dissociation rate constants of complexes in colloidal dispersions and those in homogeneous solutions originate from the differences in kinetic and mass transport conditions. In colloidal systems, when the effective rate of dissociation of the surface complexes becomes fully diffusion controlled, its value is defined via the geometrical parameters of the particle. We assess the extent to which the conventional approach of assuming a homogeneously smeared-out ligand distribution overestimates the lability of surface complexes in colloidal ligand dispersions. The validity of the theory is illustrated by application to binding of lead and cadmium by carboxyl modified latex particles: our approach correctly predicts the formation/dissociation rate constants, which differ by several orders of magnitude from their homogeneous solution counterparts.     

Incorporation conditions guiding the aggregation of a glycosylphosphatidyl inositol (GPI)-anchored protein in Langmuir monolayers

This work investigates the process of incorporation of a glycosylphosphatidyl inositol (GPI)-anchored alkaline phosphatase into Langmuir monolayers of dimyristoyl phosphatidic acid (DMPA). Three different methods of protein incorporation were assayed. When the protein solution was injected below the air–water interface after formation of the lipid monolayer a micro-heterogeneous distribution of alkaline phosphatase throughout the interface was observed. Adsorption kinetics studied by fluorescence microscopy, associated with surface pressure measurements, led to the proposition of a model in which the protein penetration is modulated by the surface packing of the monolayer and intermolecular interactions occurring between the phospholipid and the protein. At initial surface pressures higher than 20 mN m⁻¹, the protein is quickly adsorbed on the interface and the lateral diffusion drives the alkyl chains to turn towards the air phase while the polypeptide moiety faces the aqueous subphase.     

Solid-phase extraction system for Pb (II) ions enrichment based on multiwall carbon nanotubes coupled on-line to flame atomic absorption spectrometry

The present paper proposes the application of multiwall carbon nanotubes (MWCNTs) as a solid sorbent for lead preconcentration using a flow system coupled to flame atomic absorption spectrometry. The method comprises the preconcentration of Pb (II) ions at a buffered solution (pH 4.7) onto 30 mg of MWCNTs previously oxidized with concentrated HNO₃. The elution step is carried out with 1.0 mol L⁻¹ HNO₃. The effect of the experimental parameters, including sample pH, sampling flow rate, buffer and eluent concentrations were investigated by means of a 2⁴ full factorial design, while for the final optimization a Doehlert design was employed. Under the best experimental conditions the preconcentration system provided detection and quantification limits of 2.6 and 8.6 μg L⁻¹, respectively. A wide linear range varying from 8.6 up to 775 μg L⁻¹ (r > 0.999) and the respective precision (relative standard deviation) of 7.7 and 1.4% for the 15 and 200 μg L⁻¹ levels were obtained. The characteristics obtained for the performance of the flow preconcentration system were a preconcentration factor of 44.2, preconcentration efficiency of 11 min⁻¹, consumptive index of 0.45 mL and sampling frequency estimated as 14 h⁻¹. Preconcentration studies of Pb (II) ions in the presence of the majority foreign ions tested did not show interference, attesting the good performance of MWCNTs. The accuracy of the method was assessed from analysis of water samples (tap, mineral, physiological serum and synthetic seawater) and common medicinal herbs submitted to the acid decomposition (garlic and Ginkgo Biloba). The satisfactory recovery values obtained without using analyte addition method confirms the feasibility of this method for Pb (II) ions determination in different type of samples.     

2-Mercaptomethyl-thiazolidines use conserved aromatic–S interactions to achieve broad-range inhibition of metallo-β-lactamases

Infections caused by multidrug resistant (MDR) bacteria are a major public health threat. Carbapenems are among the most potent antimicrobial agents that are commercially available to treat MDR bacteria. Bacterial production of carbapenem-hydrolysing metallo-β-lactamases (MBLs) challenges their safety and efficacy, with subclass B1 MBLs hydrolysing almost all β-lactam antibiotics. MBL inhibitors would fulfil an urgent clinical need by prolonging the lifetime of these life-saving drugs. Here we report the synthesis and activity of a series of 2-mercaptomethyl-thiazolidines (MMTZs), designed to replicate MBL interactions with reaction intermediates or hydrolysis products. MMTZs are potent competitive inhibitors of B1 MBLs in vitro (e.g., K_i = 0.44 μM vs. NDM-1). Crystal structures of MMTZ complexes reveal similar binding patterns to the most clinically important B1 MBLs (NDM-1, VIM-2 and IMP-1), contrasting with previously studied thiol-based MBL inhibitors, such as bisthiazolidines (BTZs) or captopril stereoisomers, which exhibit lower, more variable potencies and multiple binding modes. MMTZ binding involves thiol coordination to the Zn(ii) site and extensive hydrophobic interactions, burying the inhibitor more deeply within the active site than d/l-captopril. Unexpectedly, MMTZ binding features a thioether–π interaction with a conserved active-site aromatic residue, consistent with their equipotent inhibition and similar binding to multiple MBLs. MMTZs penetrate multiple Enterobacterales, inhibit NDM-1 in situ, and restore carbapenem potency against clinical isolates expressing B1 MBLs. Based on their inhibitory profile and lack of eukaryotic cell toxicity, MMTZs represent a promising scaffold for MBL inhibitor development. These results also suggest sulphur–π interactions can be exploited for general ligand design in medicinal chemistry.

Metallo-β-lactamases (MBLs) are major culprits of resistance to carbapenems in bacteria. A series of thiazolidines are potent MBL inhibitors, restoring the activity of carbapenems. Metal binding and sulphur–π interactions are key to inhibition.