Deformation of doped NaCl crystals during uniaxial compression at temperatures of 4.2–293 K

The impurity weakening of crystalline NaCl:Mg and NaCl:Mn associated with purification of the matrix in a melt is demonstrated. This effect is manifested in a consistent change in the yield strength and mobility of dislocations. Its unusual temperature dependence is determined: in a number of cases weakening becomes greater as the temperature is lowered within the interval 293–4.2 K. A deviation in the elastic region of the stress-strain curves is observed to increase as the temperature is lowered. Plasticizing of crystalline NaCl is established: when the deformation temperature is lowered from 293 to 77 and 4.2 K the rate of rise in the yield strength of Cd²⁺ and Sr²⁺ doped samples is lower than that of undoped samples. An explanation for this fact is proposed. Fiz. Tverd. Tela (St. Petersburg) 39, 313–317 (February 1997) Deceased.     

Clathrate formation in the tetraisoamylammonium propionate-water system

In this paper we examine clathrate formation in the tetraisoamylammonium propionate-water binary system. We have found formation of four polyhydrates, two of which are metastable over the whole temperature range studied. All polyhydrate crystals were isolated and their compositions and densities determined; for (i-C₅H₁₁)₄NC₂H₅COO·36.5H₂O, unit cell parameters were additionally found. The results are compared with data for tetra-n-butylammonium carboxylate polyhydrates, and the structure of the title compounds is suggested. It is confirmed that the isoamyl radical stabilizes the tetradecahedral void of the clathrate hydrate framework better than the n-butyl radical. Institute of Inorganic Chemistry, Siberian Branch, Russian Academy of Sciences. Translated fromZhurnal Strukturnoi Khimii, Vol. 35, No. 3, pp. 67–71, May–June, 1994. Translated by L. Smolina     

(NH4)2MoS4在活性炭上浸渍过程的研究:Ⅱ.干燥机理及模型

（ＮＨ＿４）＿２ＭｏＳ＿４在活性炭上浸渍过程的研究Ⅱ．干燥机理及模型秦慧芳，张成芳，陆岗，俞丰，朱子彬（华东理工大学无机化工研究所，上海２００２３７）２３７）关键词硫代钼酸铵，活性炭，干燥，钼分布，干燥模型负载型催化剂的活性组分在载体上的分布，受浸渍...     

Unexpected end‐groups of poly(acrylic acid) prepared by RAFT polymerization

Low‐molecular‐weight poly(acrylic acid) (PAA) was synthesized by reversible addition fragmentation chain transfer polymerization with a trithiocarbonate as chain‐transfer agent (CTA). With a combination of NMR spectroscopy and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, the PAA end‐groups of the polymer were analyzed before and after neutralization by sodium hydroxide. The polymer prior to neutralization is made up of the expected trithiocarbonate chain‐ends and of the H‐terminated chains issued from a reaction of transfer to solvent. After neutralization, the trithiocarbonates are transformed into thiols, disulfides, thiolactones, and additional H‐terminated chains. By quantifying the different end‐groups, it was possible to demonstrate that fragmentation is the rate limiting step in the transfer reaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5439–5462, 2004     

Influence of Particle Morphology and Flow Conditions on the Dispersion Behavior of Fumed Silica in Silicone Polymers

The dispersion behavior of agglomerates of several grades of fumed silica in poly(dimethyl siloxane) liquids has been studied as a function of particle morphology and applied flow conditions. The effects of primary particle size and aggregate density and structure on cohesivity were probed through tensile and shear strength tests on particle compacts. These cohesivity tests indicated that the shear strength of particle compacts was two orders of magnitude higher than the tensile strength at the same overall packing density. Experiments carried out in both steady and time‐varying simple‐shear flows indicate that dispersion occurs through tensile failure. In the steady‐shear experiments,enhanced dispersion was obtained at higher levels of applied stress and, at comparable levels of applied stress, dispersion was found to proceed faster at higher shear rates. Experiments conducted in time‐varying flows further corroborated the results obtained in tensile cohesivity tests. Experiments in which the mean and maximum stresses in the time‐varying flows were matched to the stresses produced in steady shear flows highlight the influence of flow dynamics on dispersion behavior.     

UV curing of a novel resin derived from poly(ethylene terephthalate)

The synthesis and characterization of photopolymerizable unsaturated polyester resins based on PET waste are described. The resins came from a depolymerization process based on the glycolysis of PET by diethylene glycol (DEG). Different molecular weights of glycolysates were synthesized. Then, the latter was functionalized by a methyl hemiester of maleic acid to obtain unsatured α,ω‐bismaleate PET oligomers. In the presence of an electron donor monomer, such as triethylene glycol divinyl ether, these electron acceptor oligomers were copolymerized by way of charge‐transfer complexes under UV irradiation. The reaction was monitored in situ by real‐time IR spectroscopy to study the kinetics of photopolymerization. This one was studied in relation with the physical and chemical characteristics of oligoesters and the composition of mixtures containing divinyl ethers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1324–1335, 2007     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007