Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004     

Proteins Entrapped in Silica Monoliths Prepared from Glyceroxysilanes

The preparation of discrete polyol based silane precursors derived from glycerol by a simple one-pot process is described. These polyol-based silanes could be hydrolyzed under mild pH conditions and upon gelation resulted in the formation of optically clear, monolithic, mesoporous silica. The hydrolysis and condensation reactions lead to cure rates that are very sensitive to ionic strength, but are almost unaffected by pH in contrast to those of alkoxysilanes derived from primary alcohols such as Si(OEt)₄. Residual glycerol in the silica monolith could be removed by washing, or could be left in the silica to reduce the magnitude of shrinkage during long term storage. The biocompatible glyceroxysilane precursors lead to materials that were able to retain the activity of entrapped enzymes over repeated cycles of use for periods of up to several months.     

Composite Silica Particles Using a Mixture of Organosilane Monomers

Composite silica particles were synthesized by a two-step (acid-base) process in an aqueous solution with a mixture of organoalkoxysilane monomers. The two-step process separates the hydrolysis and condensation procedures to easily control condensation rate. In this study, the silane monomers used were phenyltrimethoxysilane (PTMS), vinyltrimethoxysilane (VTMS), methyltrimethoxysilane (MTMS), and tetraethyl-orthosilicate (TEOS). The physical properties of the resultant composite particles were investigated with the change in the molar ratio of monomers. The size of the particles increased with increasing the molar ratio of R_aSi(OR)₃/R_bSi(OR)₃ or R_aSi(OR)₃/TEOS (R_a: phenyl; R_b: vinyl, methyl).     

Synthesis and characterization of soluble polyimides containing trifluoromethyl groups in their backbone

A series of polyimides were synthesized from 2,2‐Bis(3,4‐dicarboxyphenyl)hexafluoropropane, 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane, and 4,4′‐oxydianiline by chemical imidization. The effects of the diamine ratios on the properties of the films were evaluated through the study of their thermal, electrical, and morphological properties. All the polymers exhibited better solubility in most of the organic solvents and hence were easily processable. Polyimides with more 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane exhibited better solubility and a low refractive index, which is highly desired for microelectronic applications. The dielectric constant and birefringence were strongly dependent on the fluorine content. With an increase in the fluorine substitution, both the dielectric constant and birefringence decreased. All the polymers exhibited high thermal stability (>400 °C). The absence of crystalline melting in differential scanning calorimetry and broad wide‐angle X‐ray diffraction patterns revealed the amorphous nature of the polymers, which was due to the presence of bulky CF₃ groups and hinged ether linkages of the diamine component. The residual stress values decreased with an increase in the 4,4′‐oxydianiline content, and the results were in agreement with the dielectric constant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4303–4312, 2004     

基于Apollo信号控制台的NQR炸药探测方法

介绍了一种基于Apollo信号控制台的核四极矩共振（NQR）炸药探测方法，描述了系统的结构组成、工作原理和实现方法，并给出了对RDX的测试试验结果. 试验表明该方法可实现对RDX信号的探测.     

一种新颖的用于光腔模式及光束传输模拟的特征向量法

根据有限元法单元划分的思想，提出了一种新颖的模拟光腔模式及光束传输的特征向量法. 该方法的关键之处在于基于衍射积分理论构造了一种新的光束传输矩阵，通过求解特征矩阵方程可一次性得到谐振腔的一系列特征向量，每一列特征向量即代表了腔镜上光场的一个确定模式的振幅及相位分布. 并可采用该方法模拟光场传输到腔内或腔外任意地方的场分布. 该方法将传统方法中大量的迭代过程转化成为本征积分方程特征向量的求解过程，并与初值取值无关，且可一次性求得多个模式分布，从而可方便地分析谐振腔的模式鉴别能力. 特征向量法对圆形镜共焦 关键词： 谐振腔 特征向量法 模式分布     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

GC-MS技术在舰船胶粘材料毒性评价中的应用

胶粘材料简称胶粘剂、粘合剂、粘结剂、接着剂。因其能把各种材料紧密地粘合在一起,并具有各种良好的性能,因而广泛地应用于海军舰船的制造及维修中。应用GC-MS技术对在使用环境及条件下其释放物及高温热解物的定性分析是对其进行使用过程中毒性评价的重要步骤。1实验部分1.1仪器与材料仪器:JMS-D300(日本JEOL);PIATFORMⅡGC-MS。     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

A New Triterpene from the Orchid Pholidota yunnanensis

A new triterpene, 25-methylenecyclopholidonyl p-hydroxy-trans-cinnamate, was isolated from a orchid Pholidota yunnanensis. The structure elucidation and ^1H, ^13C-NMR assignments were achieved by spectral and chemical method.