Force Chain Characteristics and Effects of a Dense Granular Flow System in a Third Body Interface During the Shear Dilatancy Process

In order to investigate the characteristics of force chains in a granular flow system, a parallel plate shear cell is constructed to simulate the shear movement of an infinite parallel plate and observe variations in relevant parameters. The shear dilatancy process is divided into three stages, namely, plastic strain, macroscopic failure, and granular recombination. The stickslip phenomenon is highly connected with the evolution of force chains during the shear dilatancy process. The load–distribution rate curves and patterns of the force chains are utilized to describe the load-carrying behaviors and morphologic changes of force chains separately. Force chains, namely, “diagonal gridding,” “tadpole-shaped,” and “pinnate” are defined according to the form of the force chains in the corresponding three stages.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Logarithmic Regge pole

This work presents the subtraction procedure and the Regge cut in the logarithmic Regge pole approach. The subtraction mechanism leads to the same asymptotic behavior as previously obtained in the non-subtraction case. The Regge cut, in contrast, introduces a clear role to the non-leading contributions for the asymptotic behavior of the total cross-section. From these results, some simple parameterization is introduced to fit the experimental data for the proton-proton and antiproton-proton total cross-section above some minimum value up to the cosmic-ray. The fit parameters obtained are used to present predictions for the \begin{document}$ \rho(s)$\end{document} -parameter as well as to the elastic slope \begin{document}$ B(s)$\end{document} at high energies.     

Experimental assessment of heat transfer and pressure drop of nanofluid as a coolant in corrugated channels

Journal of Thermal Analysis and Calorimetry - Over the last few decades, tremendous consideration is drawn towards corrugation surfaces because of their advantages over the improvement in thermal...     

Experimental investigation on heat transfer behavior of the novel ternary eutectic PCM embedded with MWCNT for thermal energy storage systems

Journal of Thermal Analysis and Calorimetry - In this paper, the variation of thermophysical properties such as the thermal conductivity, thermal energy storage capacity, viscosity, and phase...     

Development of an impedimetric sensor based on carbon dots and chitosan nanocomposite modified electrode for Cu(II) detection in water

Journal of Solid State Electrochemistry - The fast and sensitive detection of copper ions would be essential for water monitoring. Herein, we report a novel development of an impedimetric sensor...