The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Synthesis of graft copolymers with “V‐shaped” and “Y‐shaped” side chains via controlled radical and anionic polymerizations

A combination of nitroxide‐mediated radical polymerization and living anionic polymerization was used to synthesize a series of well‐defined graft (co)polymers with “V‐shaped” and “Y‐shaped” branches. The polymer main chain is a copolymer of styrene and p‐chloromethylstyrene (PS‐co‐PCMS) prepared via nitroxide‐mediated radical polymerization. The V‐shaped branches were prepared through coupling reaction of polystyrene macromonomer, carrying 1,1‐diphenylethylene terminus, with polystyryllithium or polyisoprenyllithium. The Y‐shaped branches were prepared throughfurther polymerization initiated by the V‐shaped anions. The obtained branches, carrying a living anion at the middle (V‐shaped) or at the end of the third segment (Y‐shaped), were coupled in situ with pendent benzyl chloride of PS‐co‐PCMS to form the target graft (co)polymers. The purified graft (co)polymers were analyzed by size exclusion chromatography equipped with a multiangle light scattering detector and a viscometer. The result shows that the viscosities and radii of gyration of the branched polymers are remarkably smaller than those of linear polystyrene. In addition, V‐shaped product adopts a more compact conformation in dilute solution than the Y‐shaped analogy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4013–4025, 2007     

Metallothionein as a biomarker for mercury in tissues of rat fed orally with cinnabar

Cinnabar, as one of the most widely used mineral drugs in traditional Chinese medicines, has been proven to have prominent curative effects in clinical use for more than 2000 years. But the safety and toxicity of the drug has been under constant debate in clinic usage. Metallothionein (MT) contains about 30% of cysteine in the molecule, and plays an important detoxification role against heavy metals. In this study, it was used as a biomarker to assess mercurial accumulation in rats fed orally with cinnabar. After feeding rats with cinnabar by gastric gavage at different dosages and at different times, the distribution of heavy metals (including mercury, copper and zinc) and MT was investigated among rat tissues, including liver, kidney, heart, brain, testis and blood. Metals and MT determinations were carried out using inductively coupled plasma mass spectrometry (ICP‐MS) and a modified mercury saturation assay technique respectively. The results indicated that mercury was easily accumulated in the tissues of rats exposed to cinnabar, especially in kidney. For example: at a feeding dosage of 5 g kg^?1 (bw) for 4 weeks, the mercury concentrations in kidney were 13, 8.7, 21.6 and 26 times those in liver, testis, brain and heart respectively; and at 2.5 g kg^?1 (bw) for 2 weeks, the mercury concentrations in kidney were 21, 2.1, 3 and 21 times those in liver, testis, brain and heart respectively. In addition, mercury in kidney and liver of all cinnabar groups was significantly higher than that of the control group (P < 0.01). A high positive correlation observed between MT concentrations and mercury levels in both liver and kidney (R² = 0.9299, P < 0.02 for liver; R² = 0.9923, P < 0.0008 for kidney) indicated that MT could be used as a biomarker for mercury in tissues. Copyright © 2004 John Wiley & Sons, Ltd.     

Operator‐splitting method for the analysis of cavitation in liquid‐lubricated herringbone grooved journal bearings

This paper presents an operator‐splitting method (OSM) for the solution of the universal Reynolds equation. Jakobsson–Floberg–Olsson (JFO) pressure conditions are used to study cavitation in liquid‐lubricated journal bearings. The shear flow component of the oil film is first solved by a modified upwind finite difference method. The solution of the pressure gradient flow component is computed by the Galerkin finite element method. Present OSM solutions for slider bearings are in good agreement with available analytical and experimental results. OSM is then applied to herringbone grooved journal bearings. The film pressure, cavitation areas, load capacity and attitude angle are obtained with JFO pressure conditions. The calculated load capacities are in agreement with available experimental data. However, a detailed comparison of the present results with those predicted using Reynolds pressure conditions shows some differences. The numerical results showed that the load capacity and the critical mass of the journal (linear stability indicator) are higher and the attitude angle is lower than those predicted by Reynolds pressure conditions for cases of high eccentricities. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical analysis of the rotating viscous flow approaching a solid sphere

A numerical simulation is performed to investigate the flow induced by a sphere moving along the axis of a rotating cylindrical container filled with the viscous fluid. Three‐dimensional incompressible Navier–Stokes equations are solved using a finite element method. The objective of this study is to examine the feature of waves generated by the Coriolis force at moderate Rossby numbers and that to what extent the Taylor–Proudman theorem is valid for the viscous rotating flow at small Rossby number and large Reynolds number. Calculations have been undertaken at the Rossby numbers (R_o) of 1 and 0.02 and the Reynolds numbers (R_e) of 200 and 500. When R_o=O(1), inertia waves are exhibited in the rotating flow past a sphere. The effects of the Reynolds number and the ratio of the radius of the sphere and that of the rotating cylinder on the flow structure are examined. When R_o ? 1, as predicted by the Taylor–Proudman theorem for inviscid flow, the so‐called ‘Taylor column’ is also generated in the viscous fluid flow after an evolutionary course of vortical flow structures. The initial evolution and final formation of the ‘Taylor column’ are exhibited. According to the present calculation, it has been verified that major theoretical statement about the rotating flow of the inviscid fluid may still approximately predict the rotating flow structure of the viscous fluid in a certain regime of the Reynolds number. Copyright © 2004 John Wiley & Sons, Ltd.     

Linearized and rational approximation method for solving non‐linear Burgers' equation

A new numerical method called linearized and rational approximation method is presented to solve non‐linear evolution equations. The utility of the method is demonstrated for the case of differentiation of functions involving steep gradients. The solution of Burgers' equation is presented to illustrate the effectiveness of the technique for the solution of non‐linear evolution equations exhibiting nearly discontinuous solutions. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang     

Flow-injection spectrophotometric determination of sulfadiazine and sulfamethoxazole in pharmaceuticals and urine.

A rapid and sensitive flow-injection spectrophotometric method is proposed for the determination of sulfadiazine and sulfamethoxazole. This method is based on the diazotization of sulfonamide with sodium nitrite, and a coupling reaction of the diazo-compound with alpha-naphthylamine. The optimum experimental conditions are obtained by using the controlled and weighted centroid simplex method. The linear ranges for the determination of sulfadiazine and sulfamethoxazole are 0.2-20 microg ml(-1) and 0.1-20 microg ml(-1), and their detection limits are 0.06 microg ml(-1) and 0.05 microg ml(-1), respectively, and the sampling frequency is 130 samples per hour. The method has been used to determine sulfadiazine and sulfamethoxazole in pharmaceuticals and urine without separation. The results are in agreement with those obtained by a high-performance liquid chromatograph technique at the 95% confidence level.     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003