Dynamic Variation of Excitonic Coupling in Excited Bilayer Graphene Quantum Dots?

The intermolecular interaction determines the photophysical properties of the organic aggregates, which are critical to the performance of organic photovoltaics. Here, excitonic coupling, an important intermolecular interaction in organic aggregates, between the π-stacking graphene quantum dots is studied by using transient absorption spectroscopy. We find that the spectral evolution of the ground state bleach arises from the dynamic variation of the excitonic coupling in the excited π-stacks. According to the spectral simulations, we demonstrate that the kinetics of the vibronic peak can be exploited as a probe to measure the dynamics of excitonic coupling in the excited π-stacks.     

Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

Jordan函数r次方Jrk(n)的误差项的进一步性质

设k，r分别是自然数和非零整数，Jk(n)是Jordan函数。以E(x；k，r)表示和式sum from (n≤x) Jkr(n)的渐近公式中的误差项，本文研究了E(x；k，r)的某种加权平方积分均值。     

离心力场作用下多孔介质中强制对流换热的研究

对离心流化床中空气通过多孔物料层的强制对流换热进行了理论和实验研究。获得了气流和物料间强制对流换热的准则关联式。研究结果表明,在气流速度和温度梯度方向一致的条件下,强制对流换热比通常的边界层强制对流换热有所强化,其换热的准则关联式具有 Nu=CRePr的线性形式。从而验证了改变气流方向和热流密度矢量之间夹角可以强化换热的这一强化传热新原理。     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

A new solution of reducing polymer optical fiber losses

Polymethyl methacrylate (PMMA) is one of the most commonly used optical materials. However, the application of it in the area of optical communication is strongly limited by the intrinsic absorption loss of carbon-hydrogen stretching vibration. In this paper, we present a method to solve the problem by adopting the hollow-core fibers with cobweb cladding structure. The fibers use a single dielectric material and may solve the problem of structural support. Thus the feasibility of the “OmniGuide” fibers is improved, while a series of advantages of the “OmniGuide” hollow-core fiber are retained. It is promising that a fiber with low transmission loss, high bandwidth, large-core, and low costs can be designed and fabricated using PMMA. At the same time, a very broad range of the wavelengths (from visible to near infrared region, for instance, wavelengths at 0.65-1.12 μm, and even 1.30 μm, 1.54 μm and their neighbors) may be adopted for signal wavelength.     

基于模糊集相容性的模糊控制规则优化方法

在简要介绍模糊模型的完备性和相容性的基础上 ,根据模糊集贴近度 ,提出模糊集相容性的概念 ;通过对模糊控制规则表特征的分析 ,进一步完善规则相容性概念及其定量评价方法 ;最后给出模糊控制规则模型自寻优优化方法。仿真结果表明 ,该方法可以大大提高控制系统的控制性能。     

浅析二阶齐次线性变系数微分方程的一个可积类型

本文讨论了二阶齐次线性变系数微分方程的特殊形式，给出了这种微分方程的一个可积类型．     

用不确定度评价测量结果中的有效自由度的作用

论述了有效自由度的计算方法及有效自由度量值在分析测量结果中的应用。     

Molecular dynamics simulation of processing using AFM pin tool

A three-dimensional molecular dynamics (MD) model is utilized to investigate the effect of tool geometry on the deformation process of the workpiece and the nature of deformation process at the atomic-scale. Results show that different states exist between the atomic force microscope (AFM) pin tool and the workpiece surface, i.e. the non-wear state, the ploughing state, the state in which ploughing is dominant and the state in which cutting plays a key role. A relationship between the deformation process of the workpiece and the potential energy variation is presented. The potential energy variation of atoms in different deformed regions in the workpiece such as plastically deformed region, elastically deformed region and the mixed deformation region is different. The features of variations of potential energy are discussed.