Small strain behavior of polyethylene: In situ SAXS measurements

Stack lamella deformation depends on their orientation with respect to the loading axis, the intrinsic properties of the lamellae, and the mechanical coupling between crystalline and amorphous phases. The aim of this work is to investigate the influence of the stress transmitter (ST) density and the crystallinity X_c on the local deformation. A wide experimental campaign has been undertaken on several polyethylenes with controlled molecular parameters and subjected to different thermal treatments. The ST density has been evaluated by the natural draw ratio and calculated by the Brown's model. The local deformation was measured by SAXS along a tensile test by using the long period stretching of the equatorial lamella stacks. The ratio ε_local/ε_macro was found to be a constant close to 0.5. This surprising low value has highlighted that the equatorial regions could be either the stiffest zone of the spherulite or submitted to a lower stress. It is proposed that the stability of the ratio ε_local/ε_macro is the result of two opposite phenomena: On one hand, the increase of X_c leads to unload the equatorial regions due to partial percolation of the crystalline phase and so decreases the stresses. On the other hand, when increasing X_c, the ST density decreases which causes the decrease in the local equatorial modulus. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1535–1542, 2010     

PCB-based integration of electrochemiluminescence detection for microfluidic systems

This communication presents an instrumental development based on the printed circuit board (PCB) technology to integrate electrochemiluminescence (ECL) analysis in microfluidic systems. PCB gold macro- (10 mm2) and micro- (0.09 mm2) electrodes and two ECL microfluidic devices are designed, fabricated and tested via luminol ECL detection. Potential modulation is performed between 0.7 and 0 V vs. Ag/AgCl for luminol oxidation, thus giving rise to on/off ECL responses in the presence of hydrogen peroxide. Synchronous detection is adopted to allow weak ECL signal recovery at a very low signal-to-noise ratio (SNR). The detection limit obtained with the two ECL microfluidic devices is 50 nM and 100 nM H2O2 for macroelectrodes and microelectrodes, respectively.     

Intramolecular cyclopropanation of unsaturated terminal epoxides and chlorohydrins

Lithium 2,2,6,6-tetramethylpiperidide (LTMP)-induced intramolecular cyclopropanation of unsaturated terminal epoxides provides an efficient and completely stereoselective entry to bicyclo[3.1.0]hexan-2-ols and bicyclo[4.1.0]heptan-2-ols. Further elaboration of C-5 and C-6 stannyl-substituted bicyclo[3.1.0]hexan-2-ols via Sn-Li exchange/electrophile trapping or Stille coupling generates a range of substituted bicyclic cyclopropanes. An alternative straightforward cyclopropanation protocol using a catalytic amount of 2,2,6,6-tetramethylpiperidine (TMP) allows for a convenient (1 g-7.5 kg) synthesis of bicyclo[3.1.0]hexan-2-ol and other bicyclic adducts. The synthetic utility of this chemistry has been demonstrated in a concise asymmetric synthesis of (+)-beta-cuparenone. The related unsaturated chlorohydrins also undergo intramolecular cyclopropanation via in situ epoxide formation.     

A novel fluorescent sensor for metal cations and protons based of bis-1,8-naphthalimide

A newly synthesized bis-1,8-naphthalimide aimed to increase its fluorescence intensity in the presence of protons or metal cations has been investigated. Its spectral photophysical characteristics in acetonitrile and chloroform solutions are described. The influence of metal cations (Zn(2+), Ni(2+), Ce(3+), Co(2+), Cu(2+) and Ag(+)) and protons on the fluorescence intensity has been investigate with regard to obtain fluorescence sensors for this ions in the environment.     

Mechanical and physico-chemical characterization of cyclodextrin finished polyamide fibers

We present the study of the cyclodextrin (CDs) finishing of polyamide fibers (PA) by means of citric acid (CTR) as crosslinking agent. We observed that the mode of grafting happened by the formation of a crosslinked polymer formed between CTR and CDs. This polymer physically adhered to the fibers network and was resistant to hot water washings. Modified fibers were characterized by evaluating the contact angle with a polar liquid and by studying the hysteresis of damping of PA fibers (Cahn balance) with various grafting rates and by studying the absorptivity of grafted fabrics via the technique of the posed drop (Digidrop^® instrument). Then a mechanical characterization of the PA fabrics grafted with various proportions of CDs was accomplished, by traction and tear tests by using a tensile-test bench Lohmergy. Finally a topographic study of PA grafted surfaces was approached by atomic force microscopy (AFM and LFM; contact and non-contact mode) which permitted to evaluate the roughness and the chemical heterogeneity of the grafted surfaces.     

Diastereoselective ring-closing metathesis: synthesis of P-stereogenic phosphinates from prochiral phosphinic acid derivatives

[reaction: see text] The preparation of phosphorus-containing trienes featuring two diastereotopic vinyl moieties followed by a diastereoselective ring-closing metathesis is described. This methodology allowed for the synthesis of novel highly functionalized P-stereogenic heterocycles featuring both an exo- and an endocyclic double bond. An investigation into the factors influencing the diastereochemical outcome of the ring-closing metathesis is also presented, revealing that the geometry of the double bonds conjugated to phosphorus is important and that 1,3-stereoinduction is superior to 1,4-stereoinduction for these reactions.     

A systematic study of the interactions between chemical partners (metal, ligands, counterions, and support) involved in the design of Al2O3-supported nickel catalysts from diamine-Ni(II) chelates

1.5 Ni wt %/Al2O3 catalysts have been prepared by incipient wetness impregnation using [Ni(diamine)x(H2O)(6-2x)]Y2 precursors (diamine = 1,2-ethanediamine (en) and trans-1,2-cyclohexanediamine (tc); x = 0, 1, and 2; Y = NO3- and Cl-), to avoid the formation, during calcination, of difficult-to-reduce nickel aluminate. N2 was chosen for thermal treatment to help reveal and take advantage of the reactions occurring between Ni2+, ligands, counterions, and support. In the case of [Ni(en)2(H2O)2]Y2 salts used as precursors, in situ UV-vis and DRIFT spectroscopies show that after treatment at 230 degrees C Ni(II) ions are grafted to alumina via two OAl bonds and that the diamine ligands still remain coordinated to grafted nickel ions but in a monodentate way, bridging the cation with the alumina surface. With Y = Cl-, the chloride counterions desorb as hydrogen chloride, and hydrogen released upon decomposition of the en ligands is able to reduce a fraction of nickel ions into metal as evidenced by XPS. In contrast, with Y = NO3-, compounds such as CO or NO are formed during thermal treatment, indicating that nitrate ions burn the en ligands. After thermal treatment at 500 degrees C, a surface phase containing Ni(II) ions forms, characterized by XPS and UV-vis spectroscopy. Temperature-programmed reduction shows that these ions can be quantitatively reduced to the metallic state at 500 degrees C, in contrast with the aluminate obtained when the preparation is carried out from [Ni(H2O)6]2+, which is reduced only partly at 950 degrees C. On the other hand, a total self-reduction of nickel complexes leading to 2-5-nm metal particles is obtained upon thermal treatment via the hydrogen released by a hydrogen-rich ligand such as tc, whatever the Y counterion. An appropriate choice of the ligand and the counterion allows then to obtain selectively Ni(II) ions or a dispersed reduced nickel phase after treatment in N2, as a result of the reactions occurring between the chemical partners present on alumina.     

Development of an integrated optic oxygen sensor using a novel, generic platform

This paper describes the development of a generic platform for enhanced, integrated optic sensors based on fluorescence detection. The platform employs a novel optical configuration in order to achieve enhanced performance and has inherent multianalyte detection capability. The sensor element comprises a multimode ridge waveguide that has been patterned with an analyte-sensitive fluorescent spot, which is excited directly using a LED. The platform was applied to the detection of gaseous oxygen as a proof of principle. The sol-gel-derived sensor spots were doped with an oxygen-sensitive fluorescent dichlororuthenium dye complex and intensity-based calibration data were generated from the oxygen-dependent waveguide output. The sensor achieved a LOD of 0.62% and a resolution of less than 0.96% gaseous oxygen, which compares favourably with a similar, recently reported system. This device highlights the combination of inexpensive rapid prototyping techniques and a dedicated sensor enhancement strategy that together facilitate the production of an effective prototype sensor platform.     

Catalytic Nitrene Transfer by an FeIV-Imido Complex Generated by a Comproportionation Process

Nitrene transfer reactions have emerged as one of the most powerful and versatile ways to insert an amine function to various kinds of hydrocarbon substrates. However, the mechanisms of nitrene generation have not been studied in depth albeit their formation is taken for granted in most cases without definitive evidence of their occurrence. In the present work, we compare the generation of tosylimido iron species and NTs transfer from Fe^II and Fe^III precursors where the metal is embedded in a tetracarbene macrocycle. Catalytic nitrene transfer to reference substrates (thioanisole, styrene, ethylbenzene and cyclohexane) revealed that the same active species was at play, irrespective of the ferrous versus ferric nature of the precursor. Through combination of spectroscopic (UV-visible, Mössbauer), ESI-MS and DFT studies, an Fe^IV tosylimido species was identified as the catalytically active species and was characterized spectroscopically and computationally. Whereas its formation from the Fe^II precursor was expected by a two-electron oxidative addition, its formation from an Fe^III precursor was unprecedented. Thanks to a combination of spectroscopic (UV-visible, EPR, Hyscore and Mössbauer), ESI-MS and DFT studies, we found that, when starting from the Fe^III precursor, an Fe^III tosyliodinane adduct was formed and decomposed into an Fe^V tosylimido species which generated the catalytically active Fe^IV tosylimide through a comproportionation process with the Fe^III precursor.