Measurement of Aluminum–Carbon Distances Using S‐RESPDOR NMR Experiments

It is demonstrated that reliable aluminum–carbon distances can be measured in samples with ¹³C natural abundance by NMR spectroscopy. Overcoupled resonators, with only one radio‐frequency synthesizer and one amplifier, are used to irradiate in the same pulse sequence ²⁷Al and ¹³C nuclei, which differ by only 3.6 % in Larmor frequencies. The combination of ²⁷Al saturation pulse with heteronuclear dipolar recoupling yields dipolar dephasing of the ¹³C signal, which only depends on the Al? C distance and the efficiency of the saturation pulse. Therefore, reliable distances can be obtained by rapid fitting of experimental data to an analytical expression. It is demonstrated that with natural isotopic abundance this approach allows recovery of Al? C distances of 216 pm for the covalent bond in lithium tetraalkyl aluminates, commonly used as a co‐catalyst in olefin polymerization processes, and which range from 274 to 381 pm for the three carbon atoms in aluminum lactate. The accuracy of the measured internuclear distances is carefully estimated.     

Synthesis of 2-(1-aminocyclopropyl)pyrrolidine-3,4-diol derivatives applying titanium-mediated reaction conditions

The titanium-mediated cyclopropanation reaction using Ti(OⁱPr)₃Me/EtMgBr/BF₃·OEt₂ has been applied to various 2-cyanopyrrolidines for the synthesis of functionalized 2-(1-aminocyclopropyl)pyrrolidine-3,4-diol derivatives (dideoxyiminoalditols). Under the same experimental conditions the trans-5-azidomethyl-2-cyanopyrrolidine derivative was not cyclopropanated but reduced into the corresponding 5-amino-2-cyano derivative. After polyol deprotection 2-(1-aminocyclopropyl)pyrrolidine-3,4-diols were obtained and their inhibitory activity towards 13 glycosidases has been evaluated. (2S,3S,4R,5S)-2-(1-Aminocyclopropyl)-5-methylpyrrolidine-3,4-diol (38), which has the same absolute configuration as l-fucose, is a moderate (IC₅₀=44 μM), but selective, inhibitor of α-l-fucosidase from human placenta.     

Comparison of three sequential extraction procedures used to study trace metal distribution in an acidic sandy soil

On an acid sandy soil contaminated with trace metals (Fe, Mn, Cu, Pb and Zn), three sequential extraction procedures were compared to determine the efficiency of the reagents used and the effects of the step order on the fractionation of metal species. In all cases, a magnesium nitrate solution (MgNIT) was previously used to extract exchangeable forms. In the first procedure (I), the next extraction step was performed with sodium acetate buffer (NaOAc), as used on calcareous soils, to dissolve active calcium carbonate. Then trace metals bound to different forms of oxi-hydroxides (NH(2)OH, TAMOx and TAMAs fractions) were extracted before organic matter/sulfide oxidation with hydrogen peroxide at pH 2.0 in nitric acid medium (OMHyd). Finally, residual bound metals (RESID) in each procedure were extracted with a nitric-hydrofluoric-perchloric acid mixture. The second procedure (II) was the same as I, but without the NaOAc step, because of the absence of carbonate in the study soil. In procedure III, the NaOAc step was omitted and the oxidizable organic/sulfide fraction was extracted with sodium hypochlorite at pH 8.5 (OMOCl) before the reducible fractions. This study first showed that NaOAc may remove considerable amounts of metals (especially Mn and Zn) in other forms than exchangeable ones. Procedures II and III give similar results for Fe, Mn and Zn forms, which were mainly found in fractions of inorganic soil components, but not for Cu and Pb. Copper distribution was affected by the position of the oxidation step in the sequence. In procedure II, where the oxidation step (OMHyd) ended the sequence, Cu was mainly recovered in the TAMOx fraction. However, in procedure III, where the oxidation step (OMOCl) preceded the NH(2)OH, TAMOx and TAMAs steps, Cu was found in both OMOCl and TAMOx fractions. Lead distribution varied with oxidation reagent: it was partly removed in the OMHyd fraction of procedures I and II, and to a much lower extent in the OMOCl fraction of procedure III, probably due to the alkaline pH of the reagent in the latter case.     

Dispersion polymerization of styrene in ethanol–water media: Monomer partitioning behavior and locus of polymerization

A simulation model has been developed to predict the partitioning behavior of styrene in dispersion polymerization in ethanol–water mixtures. The composition of both the continuous phase and the dispersed phase are quantitatively estimated throughout the polymerization process. The presence of water in the system causes a considerable increase of the styrene partitioning in favor of the particles. Thus, at 70°C and for an initial composition of ethanol/water/styrene = 63.3/26.9/9.8, the concentration of styrene in the particles is about 4.8 times higher than that in the serum instead of about one in pure ethanol. The higher the polymerization temperature, the lower the styrene concentration in the particles; the higher the initial styrene concentration, the higher the styrene concentration in the particles, whereas the partition coefficient is not largely effected. In contrast, neither the interfacial tension nor the final particle size do significantly alter the simulation results. The predicted data from this model have been successfully applied to clarify the mechanisms involved in dispersion polymerization, in terms of stabilization and of kinetic events. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 325–335, 1998     

Langmuir–Blodgett Films of Single-Molecule Nanomagnets

Magnetic Langmuir–Blodgett films containing well-organized monolayers of single-molecule magnets are reported. The single-molecule magnets in question are high-spin molecular clusters of the type [Mn₁₂O₁₂(carboxylate)₁₆]. The structure of such multilayered inorganic–organic composites is depicted schematically in the figure.