Preparation and properties of water‐absorbent composites of chloroprene rubber,starch, and sodium acrylate

The effects of the amounts of starch, sodium acrylate (NaAA) and dicumyl peroxide (DCP) on the properties of chloroprene rubber (CR)/starch/NaAA composites prepared by melting method were investigated. The results showed that the addition of starch improved the mechanical properties, but decreased the water‐absorbing capacity of the composite, most likely due to the decrease in the local concentration of the main water‐absorbing material sodium polyacrylate and the increase in crosslinking density of the composite resulting from the reaction between starch and CR. This reaction was verified by the vulcanized curves, DSC curves, and the cut surface morphology. The as‐prepared composite demonstrated higher water‐absorbing capacity, resulting from the incorporation of NaAA. The mechanical properties decreased with increasing the DCP loading, and the water‐absorbing ratio is the maximum at 1.0 phr DCP. The tensile strength of the composite decreased significantly after water immersion, due to the absorbed water acting as a plasticizer. The extracted component from composites after water immersion is mainly sodium polyacrylate according to Fourier transform infrared (FT‐IR) spectroscopy analysis. The morphology of the composites before and after water immersion was observed by optical transmission microscopy (OTM). The results indicated that the starch exhibits a good dispersion state, and the water‐absorbing capacity results primarily from sodium polyacrylate. Copyright © 2010 John Wiley & Sons, Ltd.     

Density functional theory study of the structure and energetics of negatively charged oligopyrroles

First‐principles calculations are used to investigate the electronic properties of negatively charged n‐pyrrole oligomers with n = 2–18. Chains of neutral oligomers are bent, whereas the negatively charged oligomers become almost planar due to accumulation of negative charge at the end monomers. Isomers of short oligomers (n < 6) display negative electron affinity although the corresponding anions are energetically stable. For longer oligomers with n ≥ 6, the electron affinity is small and positive, slowly increasing with oligopyrrole length. Doping of 12‐pyrrole with lithium atoms shows that negative oxidation states are possible due to electron transfer from dopant to oligomer at locations close to dopant. These 12‐pyrrole regions support extra negative charge and exhibit a local structural change from benzenoid to quinoid structure in the C? C backbone conjugation. Comparison between neutral and doped polypyrrole (PPy) indicates that doped polymers displays a substantial depletion of the band gap energy and the appearance of dopant‐based bands in the gap for a 50% per monomer doping level. It is predicted that Li‐doped PPy is not metallic. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Molecular dynamics simulation of ionic transport on molten Li–KCl interface

A molecular dynamics study is performed to determine the dynamics and transport properties of the ions on the molten interface between anode metal Li and electrolyte KCl. Radial distribution function of the ionic pair and the behavior of the mean‐square displacement (MSD) as a function of time (t) indicate that KCl and metal Li are in the molten state at 2,200 K in the canonical ensemble. The dynamics of the ionic transport are characterized by studying MSD for the centers of mass of the ions at different temperatures. Diffusion coefficient is evaluated from the linear slope of the MSD (t) function in the range of 0–500 ps. The MSD and diffusion coefficient of the Li⁺ ions are much larger than those of the Cl^? and K⁺ ions due to the difference in ionic characteristic. The transport process has been dominated by the Li⁺ ions on the molten interface and the Li⁺ ions are main charge carriers. The energy barrier of the Li⁺ ions transporting into the molten KCl is fitted to be 5.28 kcal/mol in the light of the activation model. The electrical conductivity of the Li⁺ ions transporting into the molten KCl are calculated from the Nernst–Einstein formula to be in the range of 0.2–0.3 S cm^?1. The current density resulted from the Li⁺ ions through the interface are estimated to be an order of 10⁶ A cm^?2, which may be the value corresponding to a larger concentration gradient of the Li⁺ ions. Simulated results at different temperatures show that the diffusion coefficient, conductivity and current density have increased with the temperature. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Fast Electrochemical Characterization of Historical Glasses Using Carbon Screen‐Printed Electrodes and Ultrasonic Assisted Sampling

A new method for lead oxide (PbO) analysis in glasses, using a carbon screen printed electrode (SPE) is proposed. A suspension of the powdered glass sample in nitric acid is prepared using an ultrasonic probe, 100 µL of slurry are deposited on the SPE and the voltammetric measurement is carried out. Structural information of PbO in the glass matrix is obtained by CV. Lead quantification is performed by DPV. In the best conditions a LOD of 2.30 wt% of PbO was obtained. The method has been applied with good results in the analysis of historical glasses samples.     

Synthesis and Characterization of Antimony(III) Complexes of Thioamides,and Crystal Structure of {[Sb(Imt)2Cl2]2((2‐Imt)}Cl2(Imt=Imidazolidine‐2‐thione)

Antimony(III) complexes of thioamides [thioamides=thiourea (Tu), N,N′‐dimethylthiourea (Dmtu), tetramethylthiourea (Tmtu), imidazolidine‐2‐thione (Imt) and diazinane‐2‐thione (Diaz)] with the general formulae, Sb(thione)_nCl₃ (n=1, 2, 2.5, 3) were prepared and characterized by elemental analysis, IR and NMR (¹H, ¹³C) spectroscopic methods. The spectral data of the complexes are consistent with the coordination of the thiones to antimony(III). The crystal structure of one of them, {[Sb(Imt)₂Cl₂]₂(μ₂‐Imt)}Cl₂ ( 1 ), was determined by X‐ray crystallography, which shows that the complex is dinuclear consisting of two [Sb(Imt)₂Cl₂] units bridged by an Imt molecule. In 1 , the antimony atom is bonded to two chlorine atoms, two sulfur atoms of coordinated Imt molecules and one sulfur atom of a bridging Imt molecule. The antimony environment can be considered to be distorted octahedral with one Cl^? ion weakly bound to antimony.     

Inclusion Complexes of Coenzyme Q10 with Polyamine‐Modified β‐Cyclodextrins: Characterization,Solubilization, and Inclusion Mode

The inclusion‐complexation behavior of coenzyme Q10 (CoQ10) with the three polyamine‐modified β‐cyclodextrins (CDs) 1 – 3 was investigated in both solution and the solid state by means of NMR, XRD, and FT‐IR spectroscopy. The results showed that the apparent solubility of CoQ10 increased linearly upon addition of hosts 1 – 3 , giving A_L‐type phase‐solubility curves. These hosts 1 – 3 were able to solubilize CoQ10 to high levels, up to 1.35, 1.52, and 1.44 mg/ml (calculated as CoQ10), respectively. The host 2 with a moderate‐length chain is the most suitable for inclusion complexation of CoQ10. Accroding to the ROESY experiments, the MeO groups of CoQ10 and the tether of 2 can be co‐included into the cavity of β‐CD through the induced‐fit interaction between host and guest. The binding ability of modified β‐CDs 1 – 3 upon complexation with CoQ10 are discussed from the viewpoints of the size/shape‐matching relationship and the induced‐fit concept between host CDs and guest CoQ10 molecule.     

Mechanistic Insights into the Ni‐Catalyzed Reductive Carboxylation of C−O Bonds in Aromatic Esters with CO2: Understanding Remarkable Ligand and Traceless‐Directing‐Group Effects

The mechanism of the Ni⁰‐catalyzed reductive carboxylation reaction of C(sp²)?O and C(sp³)?O bonds in aromatic esters with CO₂ to access valuable carboxylic acids was comprehensively studied by using DFT calculations. Computational results revealed that this transformation was composed of several key steps: C?O bond cleavage, reductive elimination, and/or CO₂ insertion. Of these steps, C?O bond cleavage was found to be rate‐determining, and it occurred through either oxidative addition to form a Ni^II intermediate, or a radical pathway that involved a bimetallic species to generate two Ni^I species through homolytic dissociation of the C?O bond. DFT calculations revealed that the oxidative addition step was preferred in the reductive carboxylation reactions of C(sp²)?O and C(sp³)?O bonds in substrates with extended π systems. In contrast, oxidative addition was highly disfavored when traceless directing groups were involved in the reductive coupling of substrates without extended π systems. In such cases, the presence of traceless directing groups allowed for docking of a second Ni⁰ catalyst, and the reactions proceed through a bimetallic radical pathway, rather than through concerted oxidative addition, to afford two Ni^I species both kinetically and thermodynamically. These theoretical mechanistic insights into the reductive carboxylation reactions of C?O bonds were also employed to investigate several experimentally observed phenomena, including ligand‐dependent reactivity and site‐selectivity.     

Synthesis of New 1,3,4‐Oxadiazol,Thiadiazole, 1,2,4‐Triazole,and Arylidene Hydrazide Derivatives of 4‐Oxo‐1,4‐dihydroquinoline with Antimicrobial Evaluation

A series of substituted 1,3,4‐oxadiazole, 1,2,4‐triazole, and 1,3,4‐thiadiazole derivatives of the substituted 3‐carboethoxy‐1,4‐dihydro‐4‐oxoquinoline have been synthesized through the reaction of the key intermediate thiosemicarbazide derivatives with different reagents. N′‐Arylidene‐4‐oxo‐1,4‐dihydroquinoline‐3‐carbohydrazides were also synthesized through the condensation reaction of the corresponding hydrazides with the appropriate aldehydes. Antimicrobial activity of some of the synthesized compounds was evaluated.