Metallo‐supramolecular micelles: Studies by analytical ultracentrifugation and electron microscopy

In aqueous solutions, amphiphilic block copolymers in which a polystyrene (PS) segment is connected to a poly(ethylene oxide) (PEO) block via a bis(2,2′:6′,2″‐ terpyridine ruthenium) complex can form micelles. Such micelles of the protomer type PS₂₀‐[Ru]‐PEO₇₀, according to the preparation procedure representing frozen micelles, were studied by sedimentation velocity and sedimentation equilibrium analysis in an analytical ultracentrifuge and by transmission electron microscopy, with different techniques applied for the sample preparation. The particles obtained were surprisingly multifarious in size. In ultracentrifugation experiments performed at relatively low salt concentrations, the distributions of the sedimentation coefficient s_20,w showed a pronounced peak at 9.6 S and a broad, only partly separated second peak around 14 S. The molar mass of the particles at the peak was around 430,000 g/mol, corresponding to an aggregation number of approximately 85. The average hydrodynamic diameter of the particles in the peak fraction was approximately 13 nm. In electron micrographs of negatively stained samples, spheres of diameters between 10 and 25 nm were the most abundant particles, but larger ones with a wide size range were also visible. The latter particles apparently were composed of smaller ones. The data from both sedimentation analysis and electron microscopy showed that (1) the studied compound formed primary micelles of diameters around 20 nm and (2) the primary micelles had a tendency toward aggregation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3159–3168, 2003     

A new VOF‐based numerical scheme for the simulation of fluid flow with free surface. Part II: application to the cavity filling and sloshing problems

Finite element analysis of fluid flow with moving free surface has been performed in 2‐D and 3‐D. The new VOF‐based numerical algorithm that has been proposed by the present authors (Int. J. Numer. Meth. Fluids, submitted) was applied to several 2‐D and 3‐D free surface flow problems. The proposed free surface tracking scheme is based on two numerical tools; the orientation vector to represent the free surface orientation in each cell and the baby‐cell to determine the fluid volume flux at each cell boundary. The proposed numerical algorithm has been applied to 2‐D and 3‐D cavity filling and sloshing problems in order to demonstrate the versatility and effectiveness of the scheme. The proposed numerical algorithm resolved successfully the free surfaces interacting with each other. The simulated results demonstrated applicability of the proposed numerical algorithm to the practical problems of large free surface motion. It has been also demonstrated that the proposed free surface tracking scheme can be easily implemented in any irregular non‐uniform grid systems and can be extended to 3‐D free surface flow problems without additional efforts. Copyright © 2003 John Wiley & Sons, Ltd.     

Ferroelectric polarization switching in nylon-11

Cold-drawn Nylon-11 films, which were prepared by stretching the melt-quenched films to a draw ratio of 2.8: 1 at room temperature, were found to exhibit an electric displacement versus electric field hysteresis loop. The results confirmed that the Nylon-11 film exhibited ferroelectric behavior at or below room temperature. The coercive fields were 65, 98, 125, 160, and 215 MV/m at 20, 0, ?20, ?40, and ?60°C and the remanent polarization at ?20°C (where there was considerably less dc conduction) was 56 mC/m². Switching of the polarization was almost completed within 20 ms.     

Diffusion via splitting and remeshing via merging in vortex methods

The technique of splitting a fat vortex element (with a core width larger than some threshold) into some thin ones in order to fix the convergence problem of the core‐spreading vortex methods is convenient and efficient. In particular, it keeps the method purely Lagrangian. In the present investigation, the splitting process is further viewed as part of the physical diffusion process. A new splitting method in which several weaker child vortices surround a thinned but still strong parent vortex is proposed. It is found that because of the survival of the parent vortex, the error arising from the splitting events can be largely reduced. The computational amount on the other hand is kept reasonably large by merging similar and close‐by vortices. The merging scheme designed herein not only involves fewer restrictions but also allows merging vortices of opposite rotations through the viewpoint of remeshing. The validity and accuracy of these techniques, proposed particularly for simulations undergoing lots of splitting and merging events, are verified by successfully simulating the interactions between two Burgers vortices under an external straining field. Copyright © 2005 John Wiley & Sons, Ltd.     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Immiscibility,upper critical solution temperature,and miscibility in blends of poly(vinyl ether)s with polyacrylics: Effects of pendant groups

Various phase behavior of blends of poly(vinyl ether)s with homologous acrylic polymers (polymethacrylates or polyacrylates) were examined using differential scanning calorimetry, optical microscopy (OM), and Fourier‐transformed infrared spectroscopy. Effects of varying the pendant groups of either of constituent polymers on the phase behavior of the blends were analyzed. A series of interestingly different phase behavior in the blends has been revealed in that as the pendant group in the acrylic polymer series gets longer, polymethacrylate/poly(vinyl methyl ether) (PVME) blends exhibit immiscibility, upper critical solution temperature (UCST), and miscibility, respectively. This study found that the true phase behavior of poly(propyl methacrylate)/PVME [and poly(isopropyl methacrylate)/PVME)] blend systems, though immiscible at ambient, actually displayed a rare UCST upon heating to higher temperatures. Similarly, as the methyl pendant group in PVE is lengthened to ethyl (i.e., PVME replaced by PVEE), phase behavior of its blends with series of polymethacrylates or polyacrylates changes correspondingly. Analyses and quantitative comparisons on four series of blends of PVE/acrylic polymer were performed to thoroughly understand the effects of pendant groups in either polyethers (PVE's) or acrylic polymers on the phase behavior of the blends of these two constituents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1521–1534, 2007     

Syntheses,crystal structures and blue emission of three zinc(II) coordination polymers with a 4,4′‐dicarboxybiphenyl sulfone ligand

Three novel zinc complexes [Zn(dbsf)(H₂O)₂] ( 1 ), [Zn(dbsf)(2,2′‐bpy)(H₂O)]·(i‐C₃H₇OH) ( 2 ) and [Zn(dbsf)(DMF)] ( 3 ) (H₂dbsf = 4,4′‐dicarboxybiphenyl sulfone, 2,2′‐bpy = 2,2′‐bipyridine, i‐C₃H₇OH = iso‐propanol, DMF = N,N‐dimethylformamide) were first obtained and characterized by single crystal X‐ray crystallography. Although the results show that all the complexes 1–3 have one‐dimensional chains formed via coordination bonds, unique three‐dimensional supramolecular structures are formed due to different coordination modes and configuration of the dbsf^2? ligand, hydrogen bonds and π–π interactions. Iso‐propanol molecules are in open channels of 2 while larger empty channels are formed in 3 . As compared with emission band of the free H₂dbsf ligand, emission peaks of the complexes 1–3 are red‐shifted, and they show blue emission, which originates from enlarging conjugation upon coordination. Copyright © 2006 John Wiley & Sons, Ltd.     

Cationic poly(methacryl oxyethyl trimethylammonium) and its poly(ethylene glycol)‐grafted analogue as capillary coating materials in electrophoresis

Cationic polyelectrolytes were synthesized and used as semipermanent coating materials for capillaries in electrophoresis. The polyelectrolytes used were a homopolymer of poly(methacryl oxyethyl trimethylammonium chloride) (PMOTAC) and its poly(ethylene glycol) (PEG)‐grafted analogue. Two PMOTAC polyelectrolytes, with molar masses of 85,000 and 300,000 g/mol, and PEG‐grafted PMOTAC with a molar mass of 280,000 g/mol were synthesized and then characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. Attachment of the polyelectrolytes to the wall of the fused silica capillary for electrophoresis caused the electroosmotic flow (EOF) to reverse. The polyelectrolyte coatings were tested over the pH range 2–11 at different buffer ionic strengths, and the most stable and strongest anodic EOFs were obtained at acidic pH values with low ionic strength buffers. Between runs the capillary is merely rinsed for 2 or 3 min with the background electrolyte solution. With the PMOTAC coatings at pH values ≤5, the RSDs of the EOFs were less than 2.9% after 60 injections. The effects of the molar mass of the polycation and of PEGylation of PMOTAC on the interactions between the polycations and basic proteins were studied at acidic pH values. The differences in the effective electrophoretic mobilities, resolution values, and plate numbers of the proteins with the different coatings were due to the EOF, as demonstrated through calculations of reduced mobilities, relative resolution values, and relative plate numbers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2655–2663, 2007     

Synthesis of grafted poly(p‐phenyleneethynylene) with energy donor–acceptor architecture via atom transfer radical polymerization: Towards nonaggregating and hole‐facilitating light‐emitting material

In this contribution, we demonstrate a new effective methodology for constructing highly efficient and durable poly(p‐phenyleneethynylene) (PPE) containing emissive material with nonaggregating and hole‐facilitating properties through the introduction of hole‐transporting blocks into the PPE system as the grafting coils as well as building the energy donor–acceptor architecture between the grafting coils and the PPE backbone. Poly(2‐(carbazol‐9‐yl)ethyl methacrylate) (PCzEMA), herein, is chosen as the hole‐transporting blocks, and incorporated into the PPE system as the grafting coils via atom transfer radical polymerization. The chemical structure of the resultant copolymer, PPE‐g‐PCzEMA, was characterized by NMR and gel permeation chromatography, showing that the desirable copolymer was obtained with the narrow polydispersity. The increased thermal stability of PPE‐g‐PCzEMA was confirmed by thermogravimetric analysis and differential scanning calorimetry along with its macroinitiator. The optoelectronic properties of this copolymer were studied in detail by ultraviolet‐visible absorption, photoluminescence emission and excitation spectra, and cyclic voltammogram (CV). The results indicate that PPE‐g‐PCzEMA exhibits the solid‐state luminescent property dominated by individual lumophores, and also the energy transfer process from the PCzEMA blocks to the PPE backbone with a relatively higher energy transfer efficiency in the solid‐state compared to that of the solution state. Additionally, the hole‐injection property is greatly facilitated due to the presence of PCzEMA, as confirmed by CV profiles. All these data indicate that PPE‐g‐PCzEMA is a good candidate for use in optoelectronic devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3776–3787, 2007