Generation of radially polarized mode using an active cylindrically symmetric birefringence fiber

A class of active fiber is presented as gain mediums of fiber lasers, where a silica layer with spoke-like air slits is introduced between the active core and cladding to obtain birefringence. With an appropriate choice of the design parameters, the fiber can support only the HE₁₁ and TM₀₁ modes. Furthermore, the numerical results show that, corresponding to the optimal rare earth doping profile, the fiber lasers can output a pure TM₀₁ mode with about 79% slope efficiency without using other mode-selective elements.     

一种晶体光纤基模色散特性的矢量法分析

利用矢量有效折射率方法(矢量法)对光子晶体光纤基模的色散特性进行了数值模拟，并与双正交归一基矢量法以及标量有效折射率方法(标量法)的模拟结果进行了对比.发现所用矢量法的结果与双正交归一基矢量法的结果符合很好，而标量法在低空气填充率f或较高归一化波数A/λ时是一种较好的近似，在空气填充率f较高或归一化波数A/λ较低时，要得到精确的结果必须利用矢量法对光子晶体光纤的特性进行模拟.讨论了光子晶体光纤包层有效折射率与光纤结构的关系. 关键词： 光子晶体光纤 矢量法 有效折射率 色散     

钙钛矿CaTiO3的超高压结构研究

利用同步辐射x射线衍射和 DAC 高压技术在室温下测量了钙钛矿CaTiO₃在压力0—44.53 GPa下的结构变化.结果表明，随着压力的增加CaTiO₃的三个晶轴都受到不同程度的压缩，a,b的压缩率相近且相对比较大，c的压缩率最小，但没有证据表明有相变的发生.在压力范围内CaTiO₃的P-V关系用Murnaghan状态方程表示，设定K′0=4，得到V0=0.2245(6)nm3和K0=222(9) GPa.应用赝立方角γpc与压力的关系，初 关键词： 3')" href="#">CaTiO₃ 结构 超高压 状态方程     

Structural Stability of CaCuMn6O12 under High Pressure and Low Temperature

In situ high pressure energy-dispersive x-ray synchrotron radiation diffraction and resistance experiments are carried out on CaCuMn6O12. Its crystal structure is stable in the measured pressure range. The equation of state of CaCuMn6O12 is obtained from the V/Vo - P relationship （V and Vo are the volumes at pressure P and at atmosphere）. The bulk modulus Bo is calculated based on the Birch-Murnaghan equation. Low temperature x-ray diffraction shows no phase transition occurring down to 160K.     

高效液相色谱法测定食品中的富马酸二甲酯

乙酸乙酯作提取剂 ,检测波长 2 30 nm,流动相采用甲醇 -水 (4∶ 6 )的乙酸钠 -冰乙酸 -四丁基溴化铵溶液 ,高效液相色谱测定月饼、面包样品中富马酸二甲酯。优化不同性质样品的提取条件及测定的流动相。不同样品的富马酸二甲酯的回收率在 93%— 95 %之间 ,在 0— 2 5 0 .0 μg/ m L校准曲线的回归方程为 y=0 .0 0 4 5 2 x 0 .0 0 5 2 3,相关系数 r=0 .9995 ,相对标准偏差小于 1.6 %。本法简单、快速、准确 ,可用于各种食品中的富马酸二甲酯的日常检测。     

多孔微结构光纤中飞秒激光脉冲超连续谱的产生

报道了利用800nm飞秒激光脉冲在多孔微结构光纤中产生超连续谱展宽的现象，连续谱展宽范围为440—890nm.基于标量波近似理论对微结构光纤包层的有效折射率和基模的有效面积以及光纤的色散特性进行了计算，发现微结构光纤具有特殊的控制色散和波导特性的能力，对超连续谱展宽的机理进行了初步解释.本文的理论分析和实验结果有较好的一致性，认为即使包层由无序填充气线组成的多孔微结构光纤也可以出现超连续谱展宽效应. 关键词： 多孔微结构光纤 超连续谱 有效折射率 色散     

激光钝化对熔石英修复后损伤性能影响的实验研究

采用10.6 μupm 的 CO₂激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值.     

基于光注入半导体激光器单周期振荡的光子微波产生及全光线宽窄化

本文对基于光注入半导体激光器的单周期动力学态产生光子微波并利用光反馈压缩其线宽进行了实验研究. 研究结果表明: 通过适当调节注入参数, 能对该方法产生的光子微波频率在数十GHz范围内进行连续、大范围地调节; 通过引入光反馈并精细调节反馈强度, 光子微波的线宽能够从40—100 MHz的范围被压缩约两个数量级至300—900 kHz范围;反馈长度对光子微波的线宽几乎没有影响, 但当反馈长度精细变化时, 光子微波频率会出现一定范围内的周期性漂移.     

Radiation characteristics and implosion dynamics of tungsten wire array Z-pinches on the YANG accelerator

We investigated the radiation characteristics and implosion dynamics of low-wire-number cylindrical tungsten wire array Z-pinches on the YANG accelerator with a peak current 0.8-1.1 MA and a rising time ～ 90 ns.The arrays are made up of(8-32)×5 μm wires 6/10 mm in diameter and 15 mm in height.The highest X-ray power obtained in the experiments was about 0.37 TW with the total radiation energy ～ 13 kJ and the energy conversion efficiency ～ 9%(24×5 μm wires,6 mm in diameter).Most of the X-ray emissions from tungsten Z-pinch plasmas were distributed in the spectral band of 100-600 eV,peaked at 250 and 375 eV.The dominant wavelengths of the wire ablation and the magneto-Rayleigh-Taylor instability were found and analyzed through measuring the time-gated self-emission and laser interferometric images.Through analyzing the implosion trajectories obtained by an optical streak camera,the run-in velocities of the Z-pinch plasmas at the end of the implosion phase were determined to be about(1.3-2.1)×10 7 cm/s.     

Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica

Two methods：high-power,short-time,single-shot irradiation（Method A） and low-power,long-time,multi-shot irradiation（Method B） are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds（LIDTs） of the mitigated sites are tested with a 355-nm,6.4-ns Nd：YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd：YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results.