Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003     

Viscoelastic properties of nanostructured natural rubber/polystyrene interpenetrating polymer networks

The effects of the blend ratio and initiating system on the viscoelastic properties of nanostructured natural rubber/polystyrene‐based interpenetrating polymer networks (IPNs) were investigated in the temperature range of ?80 to 150 °C. The studies were carried out at different frequencies (100, 50, 10, 1, and 0.1 Hz), and their effects on the damping and storage and loss moduli were analyzed. In all cases, tan δ and the storage and loss moduli showed two distinct transitions corresponding to natural rubber and polystyrene phases, which indicated that the system was not miscible on the molecular level. However, a slight inward shift was observed in the IPNs, with respect to the glass‐transition temperatures (T_g's) of the virgin polymers, showing a certain degree of miscibility or intermixing between the two phases. When the frequency increased from 0.1 to 100 Hz, the T_g values showed a positive shift in all cases. In a comparison of the three initiating systems (dicumyl peroxide, benzoyl peroxide, and azobisisobutyronitrile), the dicumyl peroxide system showed the highest modulus. The morphology of the IPNs was analyzed with transmission electron microscopy. The micrographs indicated that the system was nanostructured. An attempt was made to relate the viscoelastic behavior to the morphology of the IPNs. Various models, such as the series, parallel, Halpin–Tsai, Kerner, Coran, Takayanagi, and Davies models, were used to model the viscoelastic data. The area under the linear loss modulus curve was larger than that obtained by group contribution analysis; this showed that the damping was influenced by the phase morphology, dual‐phase continuity, and crosslinking of the phases. Finally, the homogeneity of the system was further evaluated with Cole–Cole analysis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1680–1696, 2003     

Epoxy based coatings on glass: strengthening mechanisms

Glass may be strengthened by epoxy coatings although the strengthening mechanisms remain unclear. Possible strengthening mechanisms are reviewed and are used to analyse strength data for both a solvent based and a water based coating system. The coatings either fill (solvent based coatings), or partially fill (water based coatings) surface cracks and it is shown that closure stresses arising from the thermal expansion mismatch of the coating within these cracks can account for the observed degrees of strengthening. It is also demonstrated that other suggested mechanisms such as flaw healing cannot fully account for the observed degree of strengthening.     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Crack path instabilities in DCDC experiments in the low speed regime

We studied the low speed fracture regime (10⁻⁴-10⁻⁹ m s⁻¹) in different glassy materials (soda-lime glass, glass ceramics) with variable but controlled length scale of heterogeneity. The chosen mechanical system enabled us to work in pure mode I (tensile) and at a fixed load on double cleavage drilled compression specimen. The internal residual stresses of studied samples were carefully relaxed by appropriate thermal treatment. By means of optical and atomic force microscopy techniques fracture surfaces have been examined. We have shown for the first time that the crack front line underwent an out-of-plane oscillating behavior as a result of a reproducible sequence of instabilities. The wavelength of such a phenomenon is in the micrometer range and its amplitude in the nanometer range. These features were observed for different glassy materials providing that a typical length scale characterizing internal heterogeneities was lower than a threshold limit estimated to few nanometers. This effect is the first clear experimental evidence of crack path instabilities in the low speed regime in a uniaxial loading experiment. This phenomenon has been interpreted by referring to the stability criterion for a straight crack propagation as presented by Adda-Bedia et al. [Phys. Rev. Lett. 76 (1996) 1497].     

Research problems

This section appears from time to time. Contributions are invited, and should be submitted to R. C. Thompson, Mathematics Department, University of California, Santa Barbara, CA 93106.     

Microstructural assessment of InN-on-GaN films grown by plasma-assisted MBE

The structural properties of InN thin films, grown by rf plasma-assisted molecular beam epitaxy on Ga-face GaN/Al₂O₃(0001) substrates, were investigated by means of conventional and high resolution electron microscopy. Our observations showed that a uniform InN film of total thickness up to 1 μm could be readily grown on GaN without any indication of columnar growth. A clear epitaxial orientation relationship of , was determined. The quality of the InN film was rather good, having threading dislocations as the dominant structural defect with a density in the range of 10⁹–10¹⁰ cm⁻². The crystal lattice parameters of wurtzite InN were estimated by electron diffraction analysis to be a=0.354 nm and c=0.569 nm, using Al₂O₃ as the reference crystal. Heteroepitaxial growth of InN on GaN was accomplished by the introduction of a network of three regularly spaced misfit dislocation arrays at the atomically flat interface plane. The experimentally measured distance of misfit dislocations was 2.72 nm. This is in good agreement with the theoretical value derived from the in-plane lattice mismatch of InN and GaN, which indicated that nearly full relaxation of the interfacial strain between the two crystal lattices was achieved.     

Numerical study of simultaneous natural convection heat transfer from both surfaces of a uniformly heated thin plate with arbitrary inclination

 Numerical studies were conducted to investigate the natural convection heat transfer around a uniformly heated thin plate with arbitrary inclination in an infinite space. The numerical approach was based on the finite volume technique with a nonstaggered grid arrangement. For handling the pressure–velocity coupling the SIMPLE-algorithm was used. QUICK scheme and first order upwind scheme were employed for discretization of the momentum and energy convective terms respectively. Plate width and heating rate were used to vary the modified Rayleigh number over the range of 4.8×10⁶ to 1.87×10⁸. Local and average heat transfer characteristics were compared with regarding to the inclination angle. The empirical expressions for local and average Nusselt number were correlated. It has been found that for inclination angle less than 10^∘, the flow and heat transfer characteristics are complicated and the average Nusselt number can not be correlated by one equation while for inclination angle larger than 10^∘, the average Nusselt number can be correlated into an elegant correlation. Received on 18 April 2001 / Published online: 29 November 2001     

A rapid and sensitive extractive spectrophotometric determination of copper(II) in pharmaceutical and environmental samples using benzildithiosemicarbazone.

Benzildithiosemicarbazone (BDTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of copper(II). BDTSC reacts with copper(II) in the pH range 1.0-7.0 to form a yellowish complex. Beer's law is obeyed in the concentration range 0.5-0.4 microg cm(-3). The yellowish Cu(II)-BDTSC complex in chloroform shows a maximum absorbance at 380 nm, with molar absorptivity and Sandell's sensitivity values of 1.63 x 10(4) dm3 mol(-1) cm(-1) and 0.00389 microg cm(-2), respectively. A repetition of the method is checked by finding the relative standard deviation (RSD) (n = 10), which is 0.6%. The composition of the Cu(II)-BDTSC complex is established as 1:1 by slope analysis, molar ratio and Asmus' methods. An excellent linearity with a correlation coefficient value of 0.98 is obtained for the Cu(II)-BDTSC complex. The instability constant of the complex calculated from Edmond and Birnbaum's method is 7.70 x 10(-4) and that of Asmus' method is 7.66 x 10(-4), at room temperature. The method is successfully employed for the determination copper(II) in pharmaceutical and environmental samples. The reliability of the method is assured by analyzing the standard alloys (BCS 5g, 10g, 19e, 78, 32a, 207 and 179) and by inter-comparison of experimental values, using an atomic absorption spectrometer.