Magnetic order in RCr\mathsf{_{2}}Si\mathsf{_{2}} intermetallics

The magnetic structure and ordering temperatures of three intermetallic compounds which crystallize in the tetragonal ThCr₂Si₂ structure, TbCr₂Si₂, HoCr₂Si₂ and ErCr₂Si₂, have been determined by neutron diffraction, differential scanning calorimetry and magnetization measurements. The Cr-sublattice orders anti-ferromagnetically with Néel temperatures of 758 K for TbCr₂Si₂, 718 K for HoCr₂Si₂ and 692 K for ErCr₂Si₂. Chromium atoms located at 4d crystallographic sites are aligned anti-parallel along the c-axis, with G_ZCr magnetic modes. In contrast with metallic bcc Cr, the refined room temperature value of the ordered Cr moment is anomalously large for all three compounds. No long range magnetic order of the R sublattice in TbCr₂Si₂ and HoCr₂Si₂ is observed, whilst the Er sublattice in ErCr₂Si₂ orders independently of the Cr sublattice below 2.4 K with moments ferromagnetically aligned in the basal plane.Received: 4 November 2003, Published online: 30 January 2004PACS: 75.25. + z Spin arrangements in magnetically ordered materials (including neutron and spin-polarized electron studies, synchrotron-source X-ray scattering, etc.) - 75.30.Cr Saturation moments and magnetic susceptibilities - 75.50.Ee Antiferromagnetics     

Magnetotransport and magnetic properties of InAs/Mn digital alloys

We have investigated the magnetic and magneto-transport properties of a systematic sequence of five InAs/Mn digital alloys grown by a combination of molecular beam epitaxy and atomic layer epitaxy. The samples consist of 30 periods of Mn fractional monolayers (ML) (0.17–0.5 ML) separated by 14 ML thick InAs spacer layers in a superlattice configuration. Four samples show n-type electrical conduction while the fifth (0.25 ML Mn) is p-type. Squid magnetization measurements performed on these samples show remnant magnetization above room temperature, which is apparently related to a second phase.     

Quasioptical Approach for Meniscus Lens Corrected Horn: Application to Cassegrain Systems

The Beam Mode Expansion (BME) approach for corrugated conical feed horn plus meniscus lens is presented. This approach is useful for providing the radiation pattern as it propagates through an optical system. A developed theoretical model has been verified measuring near and far field of a built horn and lens. These results have been used for designing the optical system of a Cassegrain antenna at 100GHz using the fundamental Gaussian beam mode (GBM) of the new approach. Multimode analysis has been performed with the pre-designed system in order to test the fundamental GBM results.     

Partial Differential Equations in Conformal Geometry

In this paper we present our recent work on conformally compact Einstein 4-manifolds. We present our discovery of a conformal compactification by positive eigenfunctions and many interesting consequences of this compactification in the study of topology of conformally compact Einstein 4-manifolds.     

Medicinal Organometallic Chemistry: Designing Metal Arene Complexes as Anticancer Agents

The field of medicinal inorganic chemistry is rapidly advancing. In particular organometallic complexes have much potential as therapeutic and diagnostic agents. The carbon‐bound and other ligands allow the thermodynamic and kinetic reactivity of the metal ion to be controlled and also provide a scaffold for functionalization. The establishment of structure–activity relationships and elucidation of the speciation of complexes under conditions relevant to drug testing and formulation are crucial for the further development of promising medicinal applications of organometallic complexes. Specific examples involving the design of ruthenium and osmium arene complexes as anticancer agents are discussed.     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.     

Experimental Evaluation of Strain Shielding in Distal Femur in Revision TKA

Theoretical concerns about the use of cemented and press-fit stems in revision total knee arthroplasty (TKA) include stress shielding with adverse effects on prosthesis fixation. Radiological studies have showed distal femoral bone resorption after revision TKA. The revision with use of stems can place abnormal stresses. These stresses can promote the effect of bone stress shielding and may contribute to bone loss. Experimental quantification of strain shielding in the distal synthetic femur following TKA is the main purpose of the present study. Three different constructs of TKA were assessed. The first construct included a stemless femoral component. The other two included a press-fit and a cemented femoral stem. Cortical bone strains were measured experimentally with tri-axial strain gauges in synthetic femurs before and after in-vitro knee surgery. The difference between principal strains of implanted and intact femur was calculated for each strain gauge position. This study indicates that the use of stems in distal femur changes the distribution and magnitude of bone strains. The press-fit stem provoked relevant bone area (stem length) subjected to strain shielding and also originated the highest reduction of strains in the distal region, which can potentially induce bone resorption. The stemless implanted femur produced minor bone strain changes relatively to the intact femur. The use of distal femur stems increases initial stability in the bone, but the observed reduction of strains in this region, relative to the intact femur, provokes strain shielding that can induce bone resorption and may compromise the long term implant stability.