Comparison between Eulerian and Lagrangian semi-analytical models to simulate the pollutant dispersion in the PBL

In this work we display a numerical comparison, under statistical and computational point of view, between semi-analytical Eulerian and Lagrangian dispersion models to simulate the ground-level concentration values of a passive pollutant released from a low height source. The Eulerian approach is based on the solution of the advection–diffusion equation by the Laplace transform technique. The Lagrangian approach is based on solution of the Langevin equation through the Picard’s Iterative Method. Turbulence inputs are calculated according to a parameterization capable of generating continuous values in all stability conditions and in all heights of the Planetary Boundary Layer (PBL). Numerical simulations and comparisons show a good agreement between predicted and observed concentrations values. The comparison reveals the main advantages and disadvantages between the models.     

Influence of laser repetition rate on ferroelectric properties of pulsed laser deposited BaTiO3 films on platinized silicon substrate

BaTiO₃ thin films were deposited by pulsed laser deposition on Pt–Si at different laser pulse repetition frequencies. X-ray diffraction spectra show that preferred oriented films can be grown by adjusting the pulse repetition frequency. Enhanced dielectric and ferroelectric properties obtained in films deposited at 1 Hz is attributed to preferred orientation, low strain and homogeneous grain distribution. The films deposited at 1 Hz show an impressive remanent polarization of 21.4 μC/cm² with a coercive field of 70.0 kV/cm. The shift in Curie temperature, which stems from changing the laser pulse repetition frequency, is associated with the strain state in the film.     

Simple heuristics for the assembly line worker assignment and balancing problem

We propose simple heuristics for the assembly line worker assignment and balancing problem. This problem typically occurs in assembly lines in sheltered work centers for the disabled. Different from the well-known simple assembly line balancing problem, the task execution times vary according to the assigned worker. We develop a constructive heuristic framework based on task and worker priority rules defining the order in which the tasks and workers should be assigned to the workstations. We present a number of such rules and compare their performance across three possible uses: as a stand-alone method, as an initial solution generator for meta-heuristics, and as a decoder for a hybrid genetic algorithm. Our results show that the heuristics are fast, they obtain good results as a stand-alone method and are efficient when used as a initial solution generator or as a solution decoder within more elaborate approaches.     

Invertible point transformations,Painlevé test,and the second Painlevé transcendent

The techniques of invertible point transformations and the Painlevé analysis can be used to construct integrable ordinary differential equations. We compare both techniques for the second Painlevé transcendent.     

Generic Profit Singularities in Time-Averaged Optimization for Cyclic Processes in Polydynamical Systems

We consider the optimization problem of maximizing the time-averaged profit for the motion of a smooth polydynamical system on the circle in the presence of a smooth profit density. If the problem depends on a k-dimensional parameter, then the optimal averaged profit is a function of the parameter. It is known from [4] that an optimal motion can always be selected among stationary strategies and a special type of periodic motions called level cycles. We present a classification of all generic singularities of the optimal averaged profit if k?≤?2 and the maximum is provided by level cycles.     

Residual stress analysis near a cold expanded hole in a textured alclad sheet using X-ray diffraction

In this paper we present the methods of determination and the stress obtained at the periphery of a cold expanded hole in a 2024-T3 Alclad aluminum alloy sheet. The measurements in the aluminum clad were performed by the sin²Ψ method, taking experimental precautions to deal with the texture effects. In the core aluminum a special method had to be implemented to determine the stress values in a direction not accessible to the X-ray diffraction. The strains were measured in sample orientations selected according to the texture characteristics and stress factorsF _ij were used to calculate the stress tensor. TheF _ij values were determined assuming a quasi-isotropic material behavior, after concluding that the stress results were not significantly affected by factors calculated for textured material. The residual stress profile, both in the clad and in the sheet, shows a nearly axisymmetric stress state. Compressive stresses were observed near the periphery of the hole, with values that are higher on the exit than on the entrance face. Residual stresses were also higher in the hoop direction than in the radial direction. They decreased with the radial distance to the hole and affected the previous stress state over a distance of 6 mm. The plastic deformation induced by the cold expansion is well evidenced by the FWHM values, which in the affected zone decrease with increasing distance from the hole edge.     

Cyclohexane‐1,3‐dione as a derivatizing agent for the analysis of aldehydes by micelar electrokinetic chromatography with diode array detection

Aldehydes are important compounds in a large number of samples, especially food and beverages. In this work, for the first time, cyclohexane‐1,3‐dione (CHD) was used as a derivatizing reagent aiming aldehyde (formaldehyde, acetaldehyde, propionaldehyde, and valeraldehyde) analysis by MEKC‐DAD. The optimized separation of the derivates was performed using a voltage program (+20 kV, 0–15 min.; +23 kV, 15–17 min.) at a temperature of 26°C, and using as the running buffer a mixture containing 100 mmol/L of sodium dodecyl sulfate and 29 mmol/L of sodium tetraborate at pH 9.2, with maximum absorbance at 260 nm. CHD was compared with two other derivatizing agents: 3‐methyl‐2‐benzothiazolinone hydrazone and phenylhydrazine‐4‐sulfonic acid. The CHD‐aldehyde derivatives were also characterized by LC‐MS. The calibration curves for all aldehydes had r² above 0.999 and LODs ranged from 0.01 to 0.7 mg/L. The optimized methodology was applied in sugar cane brandy (cachaça) samples successfully. CHD showed to be an alternative derivatization reagent due to its stability, aqueous solubility, high selectivity and sensitivity, reduced impurities, and simple preparation steps.     

Thermal behavior study of biodiesel standard reference materials

Quality control of fuel-related properties of biodiesel, such as thermal stability, is needed to obtain consistent engine performance by fuel users, since biodiesel is susceptible to auto-oxidation when exposed to air, light, and temperature during storage. In this work two pure standard reference materials of biodiesels produced from soy oil and animal feedstocks were studied. Differential scanning calorimetry and thermogravimetry measurements were performed and the analysis of the results revealed small temperature variations in the thermal events among the two standards, these differences are due mainly to their chemical composition, been highly influenced by the amounts of unsaturated esters.     

Inclusion of Polyphenol Oxidase Substrates in β-Cyclodextrin: A 1 H-NMR Study

A ¹H-NMR study of the interactionsbetween -cyclodextrin (-CD) and included phenolic molecules (chloragenic acid and caffeic acid ) in aqueous medium is reported. The results confirm that inclusion occurs. Data analysis by the continuous variation method shows that all the complexes have 1 : 1 stoichiometries. Values for the apparent association constants of the inclusion compounds are estimated and compared with previously reported values.