A rheological model based on primary laboratory data of lubricants with polymers additives

The present work reports some experimental data consisting in traction behavior for lubricants with polymer additives. The rheological response of lubricants without polymer additives and with additives as a function of polymer concentration, pressure and temperature is discussed. Based on the laboratory data, the paper presents a quasi-empirical approach which predicts elastic shear modulus, limiting shear stress and characteristic shear stress of a lubricant with polymer additives.     

Dynamic crystal plasticity: An Eulerian approach

In this paper an Eulerian rate-dependent single crystal model that accounts for high-strain rates, large strains and rotations is developed. The viscoplastic law as well as the evolution equations for the lattice are written in terms of vectorial and tensorial quantities associated with the current configuration. The viscoplastic law is obtained from Schmid law using an overstress approach. Such an expression for the viscoplastic law is motivated by the microdynamics of crystal defects. A general analysis of the plane-strain response of the proposed rigid-viscoplastic single crystal model is presented. It is shown that only one differential equation, involving the orientation of one composite in-plane slip system, is necessary to describe the lattice evolution. Several two-dimensional boundary value problems, such as equal-channel die extrusion and channel die compression are selected to illustrate the predictive capabilities of the model. The results show that even at relatively low strain rates the viscosity plays an important role in the development of localized deformation modes. At high crosshead velocity, the plastic properties and crystal anisotropy are less important while inertia effects are dominant. Finally, the grains interaction is investigated by analyzing the compression of a grains multicrystal.     

Mixed Convection Boundary-Layer Flow Along a Vertical Cylinder Embedded in a Porous Medium Filled by a Nanofluid

The steady mixed convection boundary-layer flow on a vertical circular cylinder embedded in a porous medium filled by a nanofluid is studied for both cases of a heated and a cooled cylinder. The governing system of partial differential equations is reduced to ordinary differential equations by assuming that the surface temperature of the cylinder and the velocity of the external (inviscid) flow vary linearly with the axial distance x measured from the leading edge. Solutions of the resulting ordinary differential equations for the flow and heat transfer characteristics are evaluated numerically for various values of the governing parameters, namely the nanoparticle volume fraction ${\phi}$ , the mixed convection or buoyancy parameter ?? and the curvature parameter ??. Results are presented for the specific case of copper nanoparticles. A critical value ?? _c of ?? with ?? _c <?0 is found, with the values of | ?? _c| increasing as the curvature parameter ?? or nanoparticle volume fraction ${\phi}$ is increased. Dual solutions are seen for all values of ?? >??? _c for both aiding, ?? >?0 and opposing, ?? <?0, flows. Asymptotic solutions are also determined for both the free convection limit ${(\lambda \gg 1)}$ and for large curvature parameter ${(\gamma \gg 1)}$ .     

Non-Darcian effects on conjugate natural convection between horizontal concentric cylinders filled with a porous medium

An analysis is presented of steady conjugate free convection between two horizontal concentric cylinders filled with a fluid-saturated porous medium; the innermost cylinder surface is maintained at a high temperature and the outermost cylinder surface at a lower one. The velocity-pressure-gradient relation is taken to be nonlinear, with departure from the linear Darcy situation measured by a parameter F₀. The investigation is based on the numerical solution, by a finite-difference method, of the full momentum and energy equations. The streamline and isotherm patterns as well as the local and mean Nusselt numbers are plotted for several physical parameters to show some of the flow and heat transfer characteristics. It is found that all parameters play an important role in the flow and heat transfer characteristics. The model can be applied to a variety of engineering problems.     

Free Convection in a Square Cavity Filled with a Tridisperse Porous Medium

This work is dealing with the natural convection heat transfer in a square filled with porous medium that has been extended according to the Nield and Kuznetsov model to tridisperse porous medium. Considering impermeable walls which the horizontal ones are insulated and vertical ones are assumed to be isothermal, the governing equations are set as the three equations for momentum and three equations for energy for three phases of porosity and are numerically solved utilizing finite element method. In this study isothermal contours, streamlines and Nusselt number values are foremost criteria which are presented for three levels of porosity. The influence of various governing parameters on the heat transfer is investigated.     

Duality for location problems with unbounded unit balls

Given an optimization problem with a composite of a convex and componentwise increasing function with a convex vector function as objective function, by means of the conjugacy approach based on the perturbation theory, we determine a dual to it. Necessary and sufficient optimality conditions are derived using strong duality. Furthermore, as special case of this problem, we consider a location problem, where the “distances” are measured by gauges of closed convex sets. We prove that the geometric characterization of the set of optimal solutions for this location problem given by Hinojosa and Puerto in a recently published paper can be obtained via the presented dual problem. Finally, the Weber and the minmax location problems with gauges are given as applications.