碱性介质中 (氢) 氧化铜修饰电极电催化氧化蔗糖

 A stable copper (hydr)oxide-modified electrode was prepared in 0.5 mol/L NaOH solution by cyclic voltammetry in the range of -250 to 1 000 mV. It can be used for electrochemical studies in the range of -250 to 1 000 mV without interfering peaks because there is no oxidation of copper. During an anodic potential sweep, the electro-oxidation of saccharose on Cu occurred by the formation of Cu^III and this reaction also occurred in the early stages of the reversed cycle until it is stopped by the negative potentials. A mechanism based on the electro-chemical generation of Cu^III active sites and their subsequent consumption by saccharose was proposed, and the rate law and kinetic parameters were obtained. The charge transfer resistance from theoretical and impedance studies was used to verify the mechanism. Under chronoamperometry regimes, the reaction followed Cottrellian behavior. The transfer of up to 21 electrons was observed in further investigations of the electro-oxidation of saccharose on a (hydr)oxide Cu rotating disk electrode.     

A new multiobjective allocator of capacitor banks and distributed generations using a new investigated differential evolution

This article has investigated a new multiobjective allocation of optimal sizing and sitting of distributed generation (DG) units and capacitor banks in simultaneous mode to improve reliability and reduce energy losses. The proposed method consists of four objectives, that is, cost of energy not supplied, system average interruption duration index, costs of energy loss and investment. A novel structure differential evolution has been suggested to solve this nonlinear complex problem and its results are compared with related values of genetic algorithm and simple differential evolutionary algorithm. In addition to the novel objective function, the other contribution of this article is proposing a new model for load and energy cost. Three types of DGs, that is, wind turbine, solar cell, and diesel generator have been used in placement process. To verify the comprehensiveness of the proposed function, three scenarios have been introduced: scenario i: first, placement of DGs, then capacitor banks, scenario ii: first, placement of capacitor banks, and then DGs, and scenario iii: simultaneous placement of DGs and capacitor banks. Simulations have been carried out on one part of practical distribution network in Metropolitan Tabriz in North West of Iran. The results of simulations have been discussed and analyzed using the five novel indices. The obtained simulation results using proposed function shows that the simultaneous placement of DGs and capacitor banks results in more reduction of the energy losses and increase improvements of reliability indices as well as voltage profile. © 2013 Wiley Periodicals, Inc. Complexity 19: 40–54, 2014     

Does Urea Preferentially Interact with Amide Moieties or Nonpolar Sidechains? A Question Answered Through a Judicious Selection of Model Systems

The transfer model suggests that urea unfolds proteins mainly by increasing the solubility of the amide backbone, probably through urea-induced increase in hydrogen bonding. Other studies suggest that urea addition increases the magnitude of solvent-solute van der Waals interactions, which increases the solubility of nonpolar sidechains. More recent analyses hypothesize that urea has a similar effect in increasing the solubility of backbone and sidechain groups. In this work, we compare the effects of urea addition on the solvation of amides and alkyl groups. At first, we study the effects of urea addition upon solvent hydrogen bonding acidity and basicity through the perturbation in the fluorescence spectrum of probes 1-AN and 1-DMAN. Our results demonstrate that the solvent's hydrogen bonding properties are minimally affected by urea addition. Subsequently, we show that urea addition does not perturb the intra-molecular hydrogen bonding in salicylic acid significantly. Finally, we investigate how urea preferentially interacts with amide and alkyl groups moieties in water by comparing the effects of urea addition upon the solubility of acetaminophen and 4-tertbutylphenol. We show that urea affects amide and t-butyl solubility (lowers the transfer free energy of both amide (backbone) and alkyl (sidechain) groups) in a similar fashion. In other words, preferential interaction of urea with both moieties contributes to protein denaturation.     

Novel optical polarizer design based on metasurface nano aperture for biological sensing in mid-infrared regime

Since Metasurfaces are playing important roles in optical devices such as optical polarizers and detectors, in this article, we have proposed a novel shape of nano aperture antenna for mid-infrared applications such as bio-sensing and other potential optical applications based on plasmonic characteristic of the gold layer over the SiN substrate. The transmittance tensor is obtained for vertical and horizontal linear polarization and base on boundary condition of the metasurface, the circular polarizations are extracted which are confirmed by the electric field distributions. We have shown by the parametric studies that the phase difference is altered by the gap and slot width and so with the dimension modification, we are able to achieve circular polarizer in the optical range. The biological materials with a thickness of 80 nm have then been placed over the metasurface layer and the figures of merits have been obtained. We have revealed that when the circular polarization is osculated to the metasurface at a special frequency the linear polarization is obtained in the other side of the metasurface. The nano aperture has been modeled and the finite difference time domain calculations are performed in CST Microwave Studio as a commercial full wave simulation software.     

Preparation and characterization of (Pebax 1657 + silica nanoparticle)/PVC mixed matrix composite membrane for CO<Subscript>2</Subscript>/N<Subscript>2</Subscript> separation

In this work, the films of poly(ether-block-amide) (Pebax 1657) and hydrophilic/hydrophobic silica nanoparticles (0–10 wt%) were coated on a poly(vinyl chloride) (PVC) ultrafiltration membrane to form new mixed matrix composite membranes (MMCMs) for CO₂/N₂ separation. The membranes were characterized by SEM, FTIR, DSC and XRD. Successful formation of a non-porous defect-free dense top layer with ~4 μm of thickness and also uniform dispersion of silica nanoparticles up to 8 wt% loading in Pebax matrix were confirmed by SEM images. The gas permeation results showed an increase in the permeance of all gases and an increase in ideal CO₂/N₂ selectivity with the increase in silica nanoparticle contents. Comparison between the incorporation of hydrophilic and hydrophobic silica nanoparticle into Pebax matrix revealed that the great enhancement of CO₂ solubility is the key factor for the performance improvement of Pebax + silica nanoparticle membranes. The best separation performance of the hydrophilic silica nanoparticle-incorporated Pebax/PVC membrane for pure gases (at 1 bar and 25 °C) was obtained with a CO₂ permeability of 124 barrer and an ideal CO₂/N₂ selectivity of 76, i.e., 63 and 35% higher than those of neat Pebax membrane, respectively. The corresponding values for hydrophobic silica nanoparticle-incorporated Pebax/PVC membrane were 107 barrer for CO₂ permeability and 61 for ideal CO₂/N₂ selectivity. Also the performances of MMCMs improved upon pressure increase (1–10 bar) owing to the shift in plasticizing effect of CO₂ towards the higher pressures. In addition, an increase in permeabilities with a decrease in ideal selectivity was observed upon temperature increase (25–50 °C) due to the intensification of chain mobility.     

Dynamics of tractor lateral overturn on slopes under the influence of position disturbances (model development)

In order to investigate the effects of forward speed, ground slope and wheel–ground friction coefficient on lateral stability of tractor at the presence of position disturbances, a tractor dynamic model was developed. In this model two types of instability were considered: instability due to overturn and skid and for each case the stability index was determined. Different geometries and mass specifications of tractor MITSUBISHI-2501D were used to examine the model. According to the results of this model forward speed and ground slope had a reverse effect on all stability indexes. Moreover stability of this tractor was more affected by tractor skidding than overturning. Therefore to improve the overall stability of this tractor, preference should be on increasing the tractor stability index derived from skid dynamics of tractor.     

Gain-bandwidth trade-off in a transistor laser: quantum well dislocation effect

The Authors report an analytical model to investigate optoelectronic characteristics reliance of a Transistor Laser on Quantum Well Location. Using simulated base recombination lifetime, optical frequency response for different quantum-well locations extracted. Slipping the well towards the collector, improves the optical bandwidth where a maximum of ≈54 GHz is observed. No resonance peak, limiting factor in diode lasers, is occurred in this enhancement method. Analyzing current gain (β) as a function of the quantum well location, exhibits a decrease in β when the well moved in the direction of the collector so that a trade-off between optical and electrical properties of transistor laser is evident. The trade-off is utilized in conjunction with previously reported experimental researches to find an optimum place of quantum well for desired performance.     

Alternative configurations for cutting machines in a tube cutting mill

In a steel tube mill where an endless stream of steel tube is supplied from a manufacturing facility, trim waste is never made regardless of cutting patterns used and the standard cutting stock problem seems meaningless. Therefore, the continuous stock cutting problem with setup is introduced to minimize the sum of cutting time and pattern changing time to meet the given demand. We propose a new configuration of cutting machines to achieve higher production efficiency, namely the open-ended configuration as opposed to the traditional closed-ended configuration, thereby two variants of the problem are defined. We propose linear formulations for both problems using binary expansion of the number of pieces of different types in a pattern. Furthermore, we define the time for pattern change as a linear function of the number of knives used in the pattern to be more realistic. Computational studies suggest that the open-ended cutting machine may improve the production time by up to 44% and that our linear formulations are more efficient than the existing ones.