Modeling of the Permeate Flux during Microfiltration of BSA-Adsorbed Microspheres in a Stirred Cell

A study on the variation of the permeate flux was performed in a stirred cell charged with microspheres, to investigate the effects of the stirrer speeds (300, 400, and 600 rpm) and the BSA concentration (0.1, 0.2, 0.4, and 0.8 g/L) under constant pressure. The permeate flux increased over time before the saturation point, but it began to decrease after that point. An increase of the BSA concentration and the stirrer speed resulted in the rapid increase of the permeate flux. This is contrary to the observation of the conventional filtration experiments using a stirred cell. A resistance-in-series model was employed for the modeling of the permeate flux. The cake resistance (R(c), induced by the concentration polarization of microspheres) and the fouling resistance (R(f), induced by the adsorption of BSA inside the membrane pore) must be considered simultaneously for the modeling. These modeling results were in good agreement with the experimental data. These can be applied to the special system considering both R(c) and R(f) as well as the general filtration systems using a stirred cell. Copyright 2000 Academic Press.     

Synthesis and Structures of Titanosiloxane Cage Compounds

Reaction of (triphenylmethyl)silanetriol (1) with cyclopentadienyltitanium trichloride (CpTiCl₃) in the presence of triethylamine as a HCl scavenger gave both compounds of a partial open-cage type {[Ph₃CSiO(OH)]₃(Ph₃CSiO_3/2)(CpTiO_3/2)₄} (2) and cube type (Ph₃CSiO_3/2CpTiO_3/2)₄ (3). The 1:1 reaction of 1 and CpTiCl₃ in toluene solvent at reflux temperature for 3 d afforded compounds 2 (22%) and 3 (36%). When 1 is reacted with a 1.5 fold excess of CpTiCl₃ under the same conditions, compound 3 was obtained in high yield (81%) along with 2 in trace quantities. Compounds 2 and 3 were fully characterized by the analyses of ¹H, ¹³C, ²⁹Si NMR, IR, and FAB MS data. The solid-state structure of 3 was determined by a single crystal X-ray diffraction study. Compound 3 had shown to have catalytic activity for the oxidation of alkenes such as 1-octene, cyclooctene, and norbornene with t-butyl hydrogen peroxide. The effect of solvent was observed in this epoxidation reaction. The order of reactivity were decreased as follows: CHCl₃ > hexane THF.     

Anomalies in the asymmetric hydroboration of olefins with the 11 adduct of (+)-α-pinene and BH3 · THF

The hydroboration of cis-2-butene and cis-3-hexene with pure diisopinocampheylborane (IPC₂BH) and monoisopinocampheylborane (IPCBH₂), both prepared from (+)-α-pinene, were studied. In contrast to IPC₂BH, which yielded R-(?)-2-butanol and R-(?)-3-hexanol in 98.4 and 94.5% optical purities, IPCBH₂ yielded S-(+)-2-butanol and S-(+)-3-hexanol in 23.6 and 19.7% optical purifies respectively. PMR examination of the methanolyzed products were utilized to establish the species present in the freshly prepared and aged $\text{1}\text{1}$ adduct from (+)-α-pinene and BH₃ · THF. The results confirm the interpretation previously advanced for the major differences realized in asymmetric hydroboration with the fresh and aged $\text{1}\text{1}$ adducts.     

A boundary element method for molecular electrostatics with electrolyte effects

A boundary element method is developed to compute the electrostatic potential inside and around molecules in an electrolyte solution. A set of boundary integral equations are derived based on the integral formulations of the Poisson equation and the linearized Poisson-Boltzmann equation. The boundary integral equations are then solved numerically after discretizing the molecular surface into a number of flat triangular elements. The method is applied to a spherical molecule for which analytical solutions are available. Use is made of both constant and linearly varying unknowns over the boundary elements, and the method is tested for various values of parameters such as the dielectric constant of the molecule, ionic strength, and the location of the interior point charge. The use of the boundary integral method incorporating the nonlinear Poisson-Boltzmann equation is also briefly discussed.     

Direct determination of estriol 3- and 16-glucuronides in pregnancy urine by column-switching liquid chromatography with electrospray tandem mass spectrometry

Using column-switching liquid chromatography/tandem mass spectrometry (LC-MS/MS), we developed an improved analytical method of urinary estriol glucuronides. This new method is derived predominantly from maternal and fetal precursors in pregnancy. We used in the following procedure: first, we filtered urine samples with a membrane filter. Next, we directly injected the 50 microL aliquot of urine samples onto a pre-column. Then, after activating the column-switching valve, we backflushed the loaded samples onto the C(18) analytical column. Urine samples can be assayed within 20 min without any sample preparation steps. We monitored separated estriol glucuronides by negative electrospray ionization (ESI) and selected-reaction monitoring (SRM). The calibration range of estriol-3-glucuronide (E3-3G) and estriol-16-glucuronide (E3-16G) was 0.1-20 microg/mL and the linearity of the method was 0.9984 for E3-3G and 0.9987 for E3-16G. The limits of detection at a signal-to-noise (S/N) ratio of 3 were 10 ng/mL (E3-3G) and 5 ng/mL (E3-16G). The analytical recovery was over 85% and, in general, inter-day and intra-day variability for precision and accuracy were less than 10%. When applied to a pregnancy urine sample to biomedical monitoring of the function of the maternal/fetal unit, the proposed method allowed rapid and sensitive screening for the detection of E3-3G and E3-16G.     

Controlled peak wavelength shift of Ca1−xSrx(SySe1−y):Eu phosphor for LED application

The highly efficient red-orange-yellow-emitting phosphor (Ca_1−xSr_x)(S_1−ySe_y):Eu²⁺ in combination with commercial green phosphor SrGa₂S₄:Eu²⁺ and blue LED are proposed for a three-band white LED. The luminescence mechanism and optimization parameters are discussed on the basis of proposed peak wavelength diagram.     

Mesoscopic structure and properties of liquid crystalline mesophase pitch and its transformation into carbon fiber

The history and present state of the art in the chemistry of mesophase pitch, which is an important precursor for carbon fiber and other high-performance industrial carbons, are reviewed relative to their structural properties. The structural concepts in both microscopic and macroscopic views are summarized in terms of the sp(2) carbon hexagonal plane as a basic unit common to graphitic materials, its planar stacking in clusters, and cluster assembly into microdomains and domains, the latter of which reflect the isochromatic unit of optical anisotropy. Such a series of structural units is described in a semiquantitative manner corresponding to the same units of graphitic materials, although the size and stacking height of the hexagonal planes (graphitic sheets) are very different. Mesophase pitch is a liquid crystal material whose basic structural concepts are maintained in the temperature range of 250 to 350 degrees C. The melt flow and thermal properties are related to its micro- and mesoscopic structure. The structure of mesophase-pitch-based carbon fiber of high tensile strength, modulus, and thermal conductivity has been formed through spinning, and has inherited the same structural concepts of mesophase pitch. Stabilization settles the structure in successive heat treatments up to 3000 degrees C. Carbonization and graphitization enable growth of the hexagonal planes and their stacking into units of graphite. Such growth is governed and controlled by the alignment of micro- and mesoscopic structures in the mesophase pitch, which define the derived carbon materials as nanostructural materials. Their properties are controlled by the nanoscopic units that are expected to behave as nanomaterials when appropriately isolated or handled.     

3β-Methoxyolean-18-ene (miliacin) from the marine fungus Chaetomium olivaceum

A pentacyclic tritepenoid, 3-methoxyolean-18-ene (miliacin), was isolated for the first time from the marine fungus Chaetomium olivaceum. Its structure was determined on the basis of 2D NMR spectroscopy and X-ray diffraction data.     

Formation mechanism of conducting polypyrrole nanotubes in reverse micelle systems

Polypyrrole (PPy) nanotubes were readily fabricated through chemical oxidation polymerization in sodium bis(2-ethylhexyl) sulfosuccinate (AOT) reverse (water-in-oil) emulsions. The reverse cylindrical micelle phase was characterized, and the key factors affecting the formation of PPy nanotubes were systematically inspected. AOT reverse cylindrical micelles were prepared via a cooperative interaction between an aqueous FeCl3 solution and AOT in an apolar solvent. In the H2O/FeCl3/AOT/apolar solvent system, the aqueous FeCl3 solution played a role in increasing the ionic strength and decreasing the second critical micelle concentration of AOT. As a result, AOT reverse cylindrical micelles could be spontaneously formed in an apolar solvent. In addition, iron cations were adsorbed to the anionic AOT headgroups that were capable of extracting metal cations from the aqueous core. Under these conditions, the addition of pyrrole monomer resulted in the chemical oxidation polymerization of the corresponding monomer at the surface of AOT reverse cylindrical micelles, followed by the formation of tubular PPy nanostructures. In a typical composition (74.0 wt % hexane, 22.4 wt % AOT, and 3.6 wt % aqueous FeCl3 solution at 15 degrees C), the average diameter of PPy nanotubes was approximately 94 nm and their length was more than 2 mum. The PPy nanotube dimensions were affected by synthetic variables such as the weight ratio of aqueous FeCl3 solution/AOT, type of apolar solvent, and reaction temperature. Moreover, the relationship between the diameter and the conductivity of the nanotubes was investigated.