The Influence of Sulfate‐Doping on the Nature of V Sites in VOx/TiO2 Catalysts

EPR, UV/Vis and FTIR spectroscopy as well as thermal analysis (TA/MS) were applied to study the influence of sulfate species present in the anatase support on the specific nature of VO_x species in supported VO_x/TiO₂ catalysts. Those sulfate species modify the local structure of the supported vanadyl species and lead to the formation of two types of VO²⁺ sites instead of only one type being formed on sulfate‐free anatase. EPR and FTIR spectroscopic measurements revealed that a part of the VO²⁺ species are directly bound to the surface sulfate species. By TA/MS it was found that SO₂ is released at lower temperature from VO_x/TiO₂ in comparison to the vanadium‐free support. The direct bonding between sulfate and VO_x species stabilizes the latter on the surface of VO_x/TiO₂ resulting in three effects: 1) a higher V site dispersion in comparison to sulfate‐free TiO₂, 2) a better resistance of surface vanadyls against diffusion into the bulk of the support and 3) a much faster reoxidation of reduced V sites than observed on sulfate‐free TiO₂.     

Stacking sequence effect of aramid–UHMPE hybrid composites by flexural test method: MATERIAL PROPERTIES

Aramid fibre–ultra-high modulus polyethylene (UHMPE) fibre interply hybrid composites were fabricated with changes in the stacking sequence. The flexural strength and modulus of hybrid composites were measured in order to investigate the effect of stacking sequence. Scanning electron microscopy (SEM) was used to examine the fracture surface of interply hybrid composites. When aramid fibre was at the compressive side and dispersion extent of fibers was small, the higher flexural strength and positive hybrid effect were observed. In addition, the different stacking sequence resulted in a change in flexural failure mechanism which had an effect on the flexural strength. As the dispersion extent of fibers decreased, the introduction of cohesive failure in aramid–aramid interface and PE–PE interface improved the flexural strength of hybrid composites.     

Diastereoselective Electrophilic Amination of Chiral 1‐Benzoyl‐2,3,5,6‐tetrahydro‐3‐methyl‐2‐(1‐methylethyl)pyrimidin‐4(1H)‐one for the Asymmetric Syntheses of α‐Substituted α,β‐Diaminopropanoic Acids

The chiral compounds (R)‐ and (S)‐1‐benzoyl‐2,3,5,6‐tetrahydro‐3‐methyl‐2‐(1‐methylethyl)pyrimidin‐4(1H)‐one ((R)‐ and (S)‐ 1 ), derived from (R)‐ and (S)‐asparagine, respectively, were used as convenient starting materials for the preparation of the enantiomerically pure α‐alkylated (alkyl=Me, Et, Bn) α,β‐diamino acids (R)‐ and (S)‐ 11 – 13 . The chiral lithium enolates of (R)‐ and (S)‐ 1 were first alkylated, and the resulting diasteroisomeric products 5 – 7 were aminated with ‘di(tert‐butyl) azodicarboxylate’ (DBAD), giving rise to the diastereoisomerically pure (≥98%) compounds 8 – 10 . The target compounds (R)‐ and (S)‐ 11 – 13 could then be obtained in good yields and high purities by a hydrolysis/hydrogenolysis/hydrolysis sequence.     

The measurement of rates of initiation in the thermal polymerization of styrene

The thermal initiation of the polymerization of styrene has been studied at temperatures from 60–140°C using DPPH as a free radical scavenger. Rates of free radical formation, measured by the decrease in absorbance at 525 nm, are about seven times greater than those obtained from inhibition period measurements. The difference is probably due to the much greater reactivity of trinitrobenzene derivatives towards diradicals from styrene than towards styryl monoradicals. This view is supported by the different behaviour of the AIBN initiated polymerization of styrene in the presence of DPPH. The thermal initiation process has a low efficiency of initiation and the activation energy is 121 kJ/mole. The results strongly support the diradical mechanism for the thermal initiation of styrene polymerization.