Effect of crack tip sharpness on the strength of vulcanized rubbers

The effect of crack tip sharpness on crack propagation in vulcanized rubbers has been studied. For very sharp cracks, tearing is found to occur on a small scale at very low energies not far above the threshold required for the onset of mechanical crack growth. The “small-scale” tearing energies show relatively little variation for rubbers that differ widely in tear strength as normally measured. Thus the latter property appears to be strongly influenced by variations in the ability of rubbers to promote tip blunting. The small-scale tear behavior is of relevance to other fracture phenomena, including cutting by sharp objects and tensile failure. Natural variations in tip sharpness occur during cyclic or time-dependent mechanical crack growth and influence the form of the crack growth characteristics.     

Voltage ‐ Current Study of an Atmospheric Dielectric Barrier Discharge

The discharge behaviour of an atmospheric dielectric barrier parallel plate discharge, used for surface treatment, is studied. Since an uniform plasma is preferable for surface treatment, filaments must be avoided in the discharge. The occurrence of filaments can be detected by measuring the current flowing through the discharge. Current and voltage measurements give an indication of the power consumption by the plasma. The power consumption of the plasma as function of the applied frequency is examined. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ion structure determinations and ion—molecule reactions by double quadrupole mass spectrometry

The QQ mass spectrometer is shown to be applicable to ion structure determination via collision-induced dissociations of mass-selected ions. The instrument can be scanned so as to record the products of dissociation as well as those of ion—molecule association reactions. The dissociations correspond to those observed at high kinetic energy in mass-analyzed ion kinetic energy spectrometers and the association reactions show parallels with reactions seen in ion cyclotron resonance spectroscopy and in high-pressure mass spectrometry     

Surface analytical characterization of oxide-free Si(100) wafer surfaces

Summary Wet-chemical cleaning procedures of Si(100) wafers are surface analytically characterized and compared. Hydrophobic surfaces show considerably less native oxides in comparison to hydrophilic surfaces.The growth of the oxide is determined as a function of exposure to air by means of XPS measurements. The chemically shifted Si2p XPS signal is utilized for the quantification of the growth kinetics.One hour after cleaning no chemically shifted Si2p XPS peak is discernible on the hydrophobic surfaces. Assuming homogeneous oxide growth, the detection limit of native oxides is estimated to be below 0.05 nm using an emission angle of 18° with respect to the wafer surface. The calculation of the oxide thickness from the chemically shifted and nonchemically shifted Si2p XPS peak intensities is carried out according to Finster and Schulze [1]. For more than a day after cleaning no surface oxides can be identified on the hydrophobic surfaces. The oxide growth kinetics is logarithmic. The very slow oxidation rate cannot be attributed to fluorine residues since no fluorine is seen by XPS. We explain the slow oxidation rate by a homogeneous hydrogen saturated Si(100) wafer surface.

---

Oberflächenanalytische Charakterisierung oxidfreier Si(100)-Waferoberflächen

     

Numerical study on performance of disk MHD generator using frozen inert gas plasma

In an magnetohydrodynamic (MHD) generator using a frozen inert gas plasma (FIP), the availability of a frozen argon plasma, the influence of plasma uniformity at the generator inlet on the performance, and the feasibility of a large-scale generator are numerically examined by /spl gamma/-/spl theta/ two-dimensional simulation. The FIP is produced by pre-ionizing inert gas without an alkali metal seed at the generator inlet, then the ionization degree of the plasma is kept almost constant in the whole of the channel because of considerable slow recombination of the inert gas just like frozen reaction plasma. It is found that not only helium, but also argon frozen plasma MHD generation is realized, although highly accurate control of inlet ionization degree is necessary for argon. It is important to reduce the nonuniformity of plasma properties at the generator inlet in order to raise the maximum enthalpy extraction ratio. Even for the large-scale generator with 1000-MW thermal input, the ionization degree is kept almost constant in the whole of the channel and the high performance is obtainable. This result is extremely attractive for the FIP MHD generator.     

Liquid-like structure of vapour quenched SnAu- and SnCu-films

SnAu- and SnCu-alloys are vapour quenched at cryogenic temperatures. Resistivity and electron diffraction patterns were recorded in situ. The scattered intensities have been normalized to interference functions. The overall agreement with those of the corresponding liquid systems is quite well. The average interatomic distances obtained from the atomic distribution functions show a concentration dependence which corresponds closely to that found in liquid SnAu and SnCu respectively. This gives evidence to the statement that the nearest neighbour organisations of the films are very similar to those of the corresponding liquids. Furthermore it turned out that the local structures in the Sn-rich SnAu-system are substantial different from those in the Sn-rich SnCu-system, except in the vicinity of a minimum amount of noble metals (8–10 at.%), which is necessary to stabilize the amorphous state.     

Reaction of 2-formyl-1,3-cyclohexanediones with cyanoacetamide

Chemistry of Heterocyclic Compounds -     

Observation of hydrogen induced intermediate borides in PrFeB based alloys by Mössbauer effect spectroscopy

In the present work, a quantitative analysis of the phase compositions by Mössbauer effect spectroscopy of solid and conventional hydrogen disproportionated Pr_13.7Fe_80.3B_6.0 and Pr_13.7Fe_63.5Co_16.7Zr_0.1B_6.0 alloys was carried out. Significant amounts of intermediate borides t-Fe₃B and Pr(Fe, Co)₁₂B₆ were detected after solid hydrogen disproportionation treatment in Pr_13.7Fe_80.3B_6.0 and Pr_13.7Fe_63.5Co_16.7Zr_0.1B_6.0 alloys, respectively. After conventional hydrogenation–disproportionation–desorption–recombination treatment these phases were not detected and in no case residual Pr₂Fe₁₄B-phase was found. It was observed that the amount of intermediate borides after disproportionation can be correlated with the degree of texture after recombination at various temperatures.     

Design and Experimental Characterization of Low‐Volume PM10/2.5/1.0 Trichotomous Sampler Inlet

This paper presents the development and laboratory evaluation of a PM10/2.5/1.0 trichotomous sampling inlet that consists of two main parts: a previously designed PM10 size‐selective inlet part and a PM2.5/1.0 two‐stage virtual impactor, which was newly fabricated and attached serially to the PM10 size selective inlet part. Particles are collected in three locations through the trichotomous sampling inlet to provide for not only particle concentration measurements of PM10, PM2.5 and PM1.0, but also those of PM2.5–10 and PM1.0–2.5.