混沌状态下永磁同步发电机的故障诊断——LMI法研究

本文以永磁同步风力发电机为研究对象, 在两相同步旋转坐标系下建立了永磁同步发电机的数学模型. 应用时间尺度和线性仿射变换建立了系统混沌模型, 验证了系统在某些参数和工作条件下会出现混沌运动. 随后在考虑系统不确定性的情况下设计了故障观测器, 在系统发生故障时, 通过所设计的故障观测器能对混沌状态下永磁同步发电机的故障做出准确估计. 仿真结果表明基于线性矩阵不等式方法的故障观测器能够对系统故障做出快速准确的诊断. 关键词： 永磁同步发电机 混沌 非线性不确定系统 故障诊断     

氧化锌锡作为电子传输层的量子点发光二极管

本文研究了以胶状量子点作为发光层和有机/无机混合材料作 为电子-空穴传输层的电致发光二极管器件. CdSe 量子点以薄膜的形式夹在无机氧化锌锡电子传输层和有机TPD空穴传输层中间构成三明治结构. 氧化锌锡电子传输层采用磁控溅射实现, 有机TPD空穴传输层和量子点发光层则采用旋涂的方法制备, 得到的QD-LEDs器件结构界面陡峭、表面平整. 光电特性表征结果显示器件的电致发光具有良好的单色性、低的开启电压, 利 用具有高电子迁移率和低载流子浓度的无机氧化锌锡薄膜作为电子传输层可 以实现器件在大气环境下稳定、明亮的电致发光. 本文分析了器件的工作机理并通过改变氧化锌锡的电导率达到控制器件中电子和空穴的注入比的目的, 优化了器件的光电性能. 关键词： 量子点 氧化锌锡 电致发光 电子传输层     

FeMn掺杂AlN薄膜的制备及其特性研究

采用直流磁控共溅射技术, 以Ar与N₂为源气体, 硅片为衬底成功地制备了Fe, Mn掺杂AlN薄膜. 利用X射线衍射和拉曼光谱研究了工作电流、靶基距离等工艺参数的改变对薄膜结构的影响. 利用扫描电子显微镜和能谱分析仪对薄膜的表面形貌和组成成分进行了分析. 利用振动样品磁强计在室温下对Fe, Mn掺杂AlN薄膜进行了磁性表征. Mn掺杂AlN薄膜表现出顺磁性的原因可能是由于Mn掺杂浓度较高, 在沉积过程部分Mn以团簇的形式存在, 反铁磁性的Mn团簇减弱了体系的铁磁交换作用. Fe掺杂AlN薄膜表现出室温铁磁性, 这可能是AlFeN三元化合物作用的结果. 随着Fe 掺杂AlN薄膜中Fe原子浓度从6.81%增加到16.17%, 其饱和磁化强度M_s由0.27 emu·cm^-3逐渐下降到0.20 emu·cm^-3, 而矫顽力H_c则由57 Oe增大到115 Oe (1 Oe=79.5775 A/m), 这一现象与Fe离子间距离的缩短及反铁磁耦合作用增强有关. 关键词： 直流磁控共溅射 氮化铝薄膜 结构 磁性     

一阶Lagrange系统的梯度表示

研究一阶Lagrange系统的梯度表示. 给出一阶Lagrange系统可成为梯度系统的条件. 利用梯度系统的性质研究系统的稳定性. 给出例子说明结果的应用. 关键词： 一阶Lagrange系统 梯度系统 稳定性     

荷控忆阻器等效电路分析模型及其电路特性研究

忆阻器是物理上新实现的具有记忆特性的基本二端电路元件. 根据φ-q关系式的泰勒级数形式构建了荷控忆阻器等效电路分析模型, 以三次非线性荷控忆阻器模型为例, 对不同参数条件下的荷控忆阻器进行了伏安关系、有无源性等电路特性的理论分析. 结果表明: 荷控忆阻器的伏安关系具有斜体“8”字形紧磁滞回线特性, 随其参数符号的不同, 荷控忆阻器呈现出无源性和有源性, 导致其电路特性发生相应的变化; 相比无源荷控忆阻器, 有源荷控忆阻器更适用于作为二次谐波信号产生电路使用. 制作了荷控忆阻器特性分析等效电路的实验电路, 实验测量结果很好地验证了理论分析结果. 关键词： 荷控忆阻器 等效电路 伏安关系 电路特性     

电场诱导氧化石墨烯的极化动力学特性研究

本文通过外加电场改变氧化石墨烯团簇分子的共振能量,利用激光激发氧化石墨烯产生的共振荧光特性测量氧化石墨烯在电场作用下的极化动力学特性. 发现存在外加电场使得荧光共振峰的半高全宽趋于饱和的时间特性,而不同的氧化石墨烯团簇分子的荧光共振峰的暂态特性同时反映了电场对氧化石墨烯产生定向极化和变形极化的动力学特性. 关键词： 氧化石墨烯 团簇分子 电场 极化动力学     

Dihydrogen bond in C2H4− n Cl n ··· NaH (n = 0, 1, 2, 3) complexes: ab initio,AIM and NBO studies

The dihydrogen-bonded complexes of ethylene and its chlorine derivatives with sodium hydride have been systematically investigated at the MP2/6-311++G(d,p) level. The studied complexes are divided into three groups (including Linear, Five- and Six-membered cyclic structures) based on the optimized structures. The structural, energetic and topological parameters are presented and analysed in terms of their possible correlation with the interaction energies and the intermolecular H?···?H distances. The nature of the electrostatic interaction in this type of dihydrogen bond has also been unveiled by means of atoms in molecules (AIM) and natural bond orbital (NBO) analysis. The effect of ring structure on the dihydrogen bonding systems has been considered by comparing with the corresponding linear structure. NBO analysis suggests that the electron density transfer (EDT) in cyclic structures have dual-channel character.     

Theory studies of the local lattice distortions and the EPR parameters for Cu2+, Mn2+ and Fe3+ centres in ZnWO4

The local lattice distortions and the electron paramagnetic resonance (EPR) parameters (g factors, hyperfine structure constants and zero-field splittings) for Cu²⁺, Mn²⁺ and Fe³⁺ in ZnWO₄ are theoretically studied based on the perturbation calculations for rhombically elongated octahedral 3d⁹ and 3d⁵ complexes. The impurity centres on Zn²⁺ sites undergo the local elongations of 0.01, 0.002 and 0.013 Å along the C₂ axis and the planar bond angle variations of 8.1°, 8.0° and 8.6° for Cu²⁺, Mn²⁺ and Fe³⁺, respectively, due to the Jahn–Teller effect and size and charge mismatch. In contrast to the host Zn²⁺ site with obvious axial elongation (～0.31 Å) and perpendicular (angular) rhombic distortion, all the impurity centres demonstrate more regular octahedral due to the above local lattice distortions. The copper centre exhibits significant Jahn–Teller reductions for the spin-orbit coupling and orbital angular momentum interactions, characterised by the Jahn–Teller reduction factor J (≈0.29 ? 1). The calculated EPR parameters agree well with the experimental results. The local structures of the impurity centres are analysed in view of the corresponding lattice distortions.     

Preparation and Surface Properties of Fluorinated Acrylates Copolymers

Copolymerization of acrylates and styrene (St) with perfluorooctylacyloxyethyl methacrylate (FA) monomer, prepared from the reaction of perfluorooctanoic acid and hydroxymethyl methacrylate, was carried out by solution polymerization. The fluorinated acrylate and St copolymers (PFA) were examined by GPC, FT-IR, and ¹H NMR. The surface tension of the PFA solution in N-methyl pyrrolidone was tested by the drop volume method. The results showed that the surface tension of the PFA solution decreased in exponential decay with increase of the PFA concentration, and the surface tension of the solution also decreased with increased addition of the FA monomer in the copolymer at the same concentration. Meanwhile, the adsorption of the PFA macromolecules in the air–solution interface increased and enrichment of the fluorinated segments on the solution surface occurred. The studies of the surface free energy, polarity, fluorine content, and morphology of the PFA films illustrated that the surface free energy and polarity of the PFA films were decreased with the augment of the FA monomer in the copolymers, and that the fluorine content and the surface roughness were increased. The surface free energy of the PFA film was as small as 16.6 mN·m^?1. The surface properties of the PFA copolymers obtained by one shot feed during polymerization were superior to those obtained by continuing feed procedure. More fluorine segregation occurred and induced the formation of a fluorine-enriched surface if the PFA copolymer was postheated. The posttreatment was thus beneficial to the improvement of the surface properties of the PFA film.     

Control of gain and thermal carrier loss profiles for mode optimization in 980-nm broad-area vertical-cavity surface-emitting lasers

Optical gain and thermal carrier loss distributions regarding current diffusion and various electric contact areas are investigated to improve the near-field modes from the ring-shape to a Gaussian-like configuration for extra-broad-area and oxide-confined vertical-cavity surface-emitting lasers. In this work an equivalent circuit network model is used. The resistance of the continuously-graded distributed Bragg reflectors （DBRs）, the current diffusion and the temperature effect due to different electric-contact areas are calculated and analyzed at first, as these parameters affect one another and are the key factors in determining the gain and thermal carrier loss. Finally, the gain and thermal carrier loss distributions are calculated and discussed.