近红外光谱结合ELM快速检测固态发酵过程参数pH值

pH值是固态发酵过程关键参数之一,为此提出基于近红外光谱技术的秸秆蛋白饲料固态发酵过程参数pH值检测方法。利用近红外光谱系统获取140个固态发酵过程产物样本在10 000～4 000cm-1范围内的近红外光谱数据,通过酸度计测得近红外光谱预测模型的参考测量值;运用ELM算法建立pH值的预测模型,在模型建立过程中由交互验证法确定最佳主成分因子数和ELM网络隐含层节点数。试验结果显示:最佳ELM网络模型的拓扑结构为10-40-1,模型预测集相关系数(Rp)和预测均方根误差(RMSEP)分别为0.961 8和0.104 4。研究结果可为固态发酵过程参数的在线检测提供技术基础。     

Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica

Two methods：high-power,short-time,single-shot irradiation（Method A） and low-power,long-time,multi-shot irradiation（Method B） are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds（LIDTs） of the mitigated sites are tested with a 355-nm,6.4-ns Nd：YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd：YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results.     

Photonic generation of arbitrary waveforms based on incoherent wavelength-to-time mapping

We demonstrate experimentally a radio frequency arbitrary waveform generator using the incoherent wavelengthto-time mapping technique.The system is implemented by amplitude modulation of a broadband optical resource whose spectrum is reshaped by a programmable optical pulse shaper and transmitted over a single mode fiber link.The shape of the generated waveform is controlled by the optical pulse shaper,and the fiber link introduces a certain group velocity delay to implement wavelength-to-time mapping.Assisted by the flexible optical pulse shaper,we obtain different shapes of optical waveforms,such as rectangle,triangle,and sawtooth waveforms.Furthermore,we also demonstrate ultra-wideband generation,such as Gaussian monocycle,doublet,and triplet waveforms,using the incoherent technique.     

Autoparametric vibration absorber effect to reduce the first symmetric mode vibration of a curved beam/panel

This paper presents the implementation of autoparametric phenomena to reduce the symmetrical vibration of a curved beam/panel under external harmonic excitation. The internal energy transfer of a first symmetric mode into first anti-symmetric mode in a curved panel is one example of autoparametric vibration absorber effect. This is similar to the vibration energy transfer from the resonance of a primary structure to the resonance of a secondary spring–mass (tuned mass damper). The nonlinear response of a curved beam is analyzed using an equation with two modes, and a shaker test. The effect of different configurations of the curve beam/panel, including damping ratios and excitation levels, on the energy transfer of the first symmetric mode to the first anti-symmetric mode was studied.The conventional tuned mass damper (TMD) can reduce the resonance response by energy transfer using damping dissipation, whereas an autoparametric vibration absorber (AVA) can reduce the resonance response by energy transfer using parametric interaction. The results indicate that there is a non-absorption region in which vibration is amplified. For the AVA, the non-absorption region can be minimized by tuning the resonance frequency of the first anti-symmetric mode to half of the first symmetric mode resonance frequency using additional mass. No additional damping material is required for achieving sufficient vibration reduction. The AVA can maintain reliable performance in hot and corrosive environments where damping material cannot perform effectively. This paper presents the first successful experimental results of an autoparametric vibration absorption mechanism in a curved beam.     

无序度对一维长程关联无序系统中局域化-退局域化转变的影响

对长程幂律关联能量序列进行了修正,使其能体现出无序度在一维长程关联无序系统中的影响,并利用重正化群方法,计算了能反映该系统局域化-退局域化转变的Lyapunov指数.结果表明,在由于关联指数p的影响而在系统中出现的局域化向退局域化的转变中,无序度起着相反的作用.当关联指数p一定而无序度W增大时,系统中心能区范围内由于长程关联而引起的扩展态逐渐向局域态转变.当无序度W增大到某一临界值W_c时,系统中所有本征态均转变为局 关键词： 长程关联 Lyapunov指数 无序度 局域化-退局域化转变     

大功率半导体激光泵浦固体激光器脉冲电源设计

介绍一种大功率半导体激光泵浦固体激光器(DPSSL)脉冲驱动电源的设计电路及其控制方法。根据半导体激光器的工作特性,采用前级电容充电电路与后级脉冲电流产生电路相结合的电路结构。由于LCC谐振电路具有软开关特性和抗负载短路、开路的能力,又能够实现对储能电容恒流充电的功能,因此其适合做为脉冲电源中储能电容的充电电路;后级脉冲电流产生电路选择大功率MOSFET做为主控器件,利用MOSFET饱和区的漏极电流可控性,通过栅极电压控制产生负载脉冲电流。控制部分采用模拟与数字相结合的控制方式,使脉冲电源控制更加灵活,引入脉冲电流指令给定积分器,可以更有效地控制脉冲电流上升过程,抑制电流过冲,提高控制精度,使脉冲驱动电源产生类似矩形波的大功率脉冲电流。搭建了脉冲功率为28 kW的实验平台,实验达到的指标：脉冲电流幅值80 A,脉冲电压350 V,脉冲宽度100 μs,重复频率100 Hz。     

同心度对杆箍缩二极管物理特性的影响

闪光X射线照相是获得高凝聚态物质内部物理图像的重要手段,阳极杆箍缩二极管是X射线源的重要组成部分之一,其设计直接影响X射线源稳定性。由于受装置结构及真空等因素的影响,使得阴阳极几何中心同心存在一定的困难。因此,评估同心偏差对二极管物理特性的影响,对提高闪光X射线源稳定性具有重要的意义。针对阴阳极几何中心同心偏差问题开展实验研究,分别取三种同心偏差度(小于1%,15.02%和22.92%)状态。在1 MV电压下获得了不同同心偏差度下二极管电参数特性,并在此基础上结合理论模型分析了同心偏差度对二极管物理特性及电极等离子体扩散速度的影响。研究结果表明,随着同心偏差度增加,磁绝缘阶段阻抗下降率及等离子体扩散速度呈非线性增加,同时造成该阶段二极管阻抗与脉冲驱动源输出阻抗失配严重,降低了二极管与脉冲驱动源的能量耦合效率。     

反馈调节的局部正则化鲁棒光流估计

提出了一种引入反馈调节机制的新局部鲁棒光流场计算思想.该思想结合局部法和全局法的特点,首先划分整场为有公共边界的子块,定义距离来判断每个点的子块归属,然后在每个子块内进行光流约束和平滑约束正则化的优化计算.将光流约束中的光强残差作为控制参量,衡量光流准确度的峰值信噪比作为输出,经反馈处理,调节控制参量使光流估计准确度趋向最优.实验结果表明,这种新的结合反馈调节机制局部光流场计算法能使光流准确度获得提升.     

锐钛矿相TiO2纳米管的制备及其染科敏化太阳电池

以商用金红石相TiO2粉末为原料,通过在碱性溶液中150℃水热48h的方法合TiO2纳米管.采用SEM,TEN,XRD分析手段对TiO2纳米管的形貌和结构演变进行了表征.制成的TiO2纳米管与TritonX-100,乙酰丙酮混合后,通过丝网印刷的方法涂敷到ITO导电玻璃衬底上,并且在450℃下烧结30min后得到可应用于染料敏化太阳电池的多孔光阳极.将此光阳极浸泡于N719染料敏化后,与镀铂对电极组装电池,两者之间灌入液态电解质,电池的有效面积为0.28 cm2.在标准氙灯模拟器下(AM 1.5,100 roW/cm2)测试r电池的J-V特性,得到2.17%的光电转换效率.     

柔性有机电致发光器件导电基板的工艺性能

在聚对苯二甲酸乙二醇酯(PET)柔性衬底上采用直流磁控溅射技术制备了氧化铟锡(ITO)透明导电薄膜,研究了衬底温度、溅射功率和溅射压强等工艺条件对薄膜光电性能的影响,并利用原子力显微镜(AFM)表征了衬底及ITO薄膜的表面形貌。结果表明,在PET衬底温度50℃、溅射功率100W和溅射压强2.66×10-1Pa的条件下,可以得到低方阻(50Ω/□)和高透过率(>90%)的透明导电薄膜。以此柔性ITO衬底为阳极,制备了结构为PET/ITO/NPB/Alq3/Mg∶Ag的柔性有机电致发光器件,在驱动电压为13V时,器件的发光亮度达到了2834cd/m2。