Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

二次阳极氧化方法制备有序多孔氧化铝膜

通过二次阳极氧化方法制备多孔氧化铝膜与一次阳极氧化方法制备多孔氧化铝膜孔排布规律性的对比 ,结果发现 ,二次阳极氧化方法制取的多孔氧化铝膜孔排布规律性明显好于一次阳极氧化法制取的多孔膜 .在几个微米范围内 ,孔呈理想的六角排布 .去除一次阳极氧化膜后 ,二次阳极氧化得以在更良好的表面进行 ,制取的氧化铝膜孔规律性和有序度更高 .有序区域的尺寸与晶粒内的亚晶大小有一定关系     

二维椭圆型方程反问题中优化算法的比较

近年来，决定椭圆型方程系数反问题在地磁、地球物理、冶金和生物等实际问题上有着广泛的应用．本文讨论了二维的决定椭圆型方程系数反问题的数值求解方法．由误差平方和最小原则，这个反问题可化为一个变分问题，并进一步离散化为一个最优化问题，其目标函数依赖于要决定的方程系数．本文着重考察非线性共轭梯度法在此最优化问题数值计算中的表现，并与拟牛顿法作为对比．为了提高算法的效率我们适当选择加快收敛速度的预处理矩阵．同时还考察了线搜索方法的不同对优化算法的影响．数值实验的结果表明，非线性共轭梯度法在这类大规模优化问题中相对于拟牛顿法更有效．     

GREEN’S FUNCTION AND EFFECTIVE ELASTIC STIFFNESS TENSOR FOR ARBITRARY AGGREGATES OF CUBIC CRYSTALS

A closed but approximate formula of Green’s function for an arbitrary aggregate of cubic crystallites is given to derive the e?ective elastic sti?ness tensor of the polycrystal. This formula, which includes three elastic constants of single cubic c…     

Synthesis of a soluble pyrrole copolymer with phenetidine

A new series of copolymers was synthesized through the oxidative polymerization of pyrrole (PY) and o‐phenetidine (PHT) with inorganic oxidants in acidic media. The polymerization parameters including the mixing method of the oxidant with the comonomer, the comonomer ratio, the time, the temperature, the oxidant, the organic medium, and the acid were systematically optimized for the synthesis of copolymers with high yields, intrinsic viscosities, and solubility. The resultant copolymers were characterized by elemental analysis, infrared, ultraviolet–visible, solution high‐resolution ¹H NMR and solid‐state high‐resolution ¹³C NMR, circular dichroism spectroscopy, and cyclic voltammetry. The results showed that the PY observed content in the copolymers was much higher than the PY feed content. The regular variation of the polymerization yield, intrinsic viscosity, solubility, macromolecular structure, and electroactivity of the resulting polymers with the comonomer ratio, together with the complete solubility of a PY/PHT (10/90) polymer in highly polar solvents, indicated the formation of real random copolymers containing both PY and PHT units rather than a mixture of two homopolymers. However, the polymers containing more than 59 mol % PY were not homogeneous copolymers consisting of soluble and insoluble parts. A semiquantitative relationship between the polymerization yield or solubility of the copolymers and the polarity index of the organic solvents was examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2073–2092, 2004     

Living polymerization of styrene initiated by mercaptan/ε‐caprolactam

The bulk polymerization of styrene initiated by ?‐caprolactam (CL) and n‐dodecyl mercaptan (RSH) has been explored. This novel polymerization system shows living characteristics. For example, the molecular weight of the resulting polymers increases with conversion, and the system has the ability to form diblock copolymers and so forth. The polymer chain end contains thiol and lactam structures, which we have investigated with Fourier transform infrared, ¹H NMR, and ¹³C NMR techniques. Electron spin resonance spectra and theoretical calculations by the Hartree–Fock methods have been used to examine the mechanism. The results reveal that the initial polymerization starts from thiol via a chain‐transfer reaction, and the propagation proceeds by the insertion of a monomer between the terminal group and the intermediate structure of lactam. Finally, the polymerization kinetics have been examined. The polymerization rate varies linearly with the concentration of CL and RSH, and this confirms the mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4976–4993, 2004     

Synthesis and characterization of new segmented polyurethanes with side‐chain,liquid‐crystalline chain extenders

Liquid‐crystalline, segmented polyurethanes with methoxy–biphenyl mesogens pendant on the chain extender were synthesized by the conventional prepolymer technique and esterification reaction. Two, side‐chain, liquid‐crystalline (SCLC) polyurethanes with mesogens having spacers of six and eight methylene units were prepared. The structures of the mesogenic units and SCLC polyurethanes were confirmed by Fourier transform infrared spectroscopy and ¹H NMR. Polymer properties were also examined by solubility tests, water uptakes, and inherent viscosity measurements. Differential scanning calorimetry studies indicated that the transition temperature of the isotropic to the liquid‐crystalline phase decreased with increasing spacer length. Wide‐angle X‐ray diffraction (WAXD) studies revealed the existence of liquid‐crystalline phases for both SCLC polyurethanes. Polarized optical microscopic investigations further confirmed the thermotropic liquid‐crystalline behaviors and nematic mesophases of both samples. Thermogravimetric analysis displayed better thermal stabilities for both SCLC polymers and indicated that the presence of mesogenic side chains may increase the thermal stability of segmented polyurethanes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 290–302, 2004     

Behavior and surface energies of polybenzoxazines formed by polymerization with argon,oxygen, and hydrogen plasmas

Polybenzoxazine (PBZZ) thin films can be fabricated by the plasma‐polymerization technique with, as the energy source, plasmas of argon, oxygen, or hydrogen atoms and ions. When benzoxazine (BZZ) films are polymerized through the use of high‐energy argon atoms, electronegative oxygen atoms, or excited hydrogen atoms, the PBZZ films that form possess different properties and morphologies in their surfaces. High‐energy argon atoms provide a thermodynamic factor to initiate the ring‐opening polymerization of BZZ and result in the polymer surface having a grid‐like structure. The ring‐opening polymerization of the BZZ film that is initiated by cationic species such as oxygen atoms in plasma, is propagated around nodule structures to form the PBZZ. The excited hydrogen atom plasma initiates both polymerization and decomposition reactions simultaneously in the BZZ film and results in the formation of a porous structure on the PBZZ surface. We evaluated the surface energies of the PBZZ films polymerized by the action of these three plasmas by measuring the contact angles of diiodomethane and water droplets. The surface roughness of the films range from 0.5 to 26 nm, depending on the type of carrier gas and the plasma‐polymerization time. By estimating changes in thickness, we found that the PBZZ film synthesized by the oxygen plasma‐polymerization process undergoes the slowest rate of etching in CF₄ plasma. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4063–4074, 2004     

Influence of solvents on the formation of ultrathin uniform poly(vinyl pyrrolidone) nanofibers with electrospinning

Although there have been many reports on the preparation and applications of various polymer nanofibers with the electrospinning technique, the understanding of synthetic parameters in electrospinning remains limited. In this article, we investigate experimentally the influence of solvents on the morphology of the poly(vinyl pyrrolidone) (PVP) micro/nanofibers prepared by electrospinning PVP solution in different solvents, including ethanol, dichloromethane (MC) and N,N‐dimethylformamide (DMF). Using 4 wt % PVP solutions, the PVP fibers prepared from MC and DMF solvents had a shape like a bead‐on‐a‐string. In contrast, smooth PVP nanofibers were obtained with ethanol as a solvent although the size distribution of the fibers was somewhat broadened. In an effort to prepare PVP nanofibers with small diameters and narrow size distributions, we developed a strategy of using mixed solvents. The experimental results showed that when the ratio of DMF to ethanol was 50:50 (w/w), regular cylindrical PVP nanofibers with a diameter of 20 nm were successfully prepared. The formation of these thinnest nanofibers could be attributed to the combined effects of ethanol and DMF solvents that optimize the solution viscosity and charge density of the polymer jet. In addition, an interesting helical‐shaped fiber was obtained from 20 wt % PVP solution in a 50:50 (w/w) mixed ethanol/DMF solvent. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3721–3726, 2004