Simulating physiological conditions to evaluate nanoparticles for magnetic fluid hyperthermia (MFH) therapy applications

Magnetite nanoparticles with high self-heating capacity and low toxicity characteristics are a promising candidate for cancer hyperthermia treatment. In order to achieve minimum dosage to a patient, magnetic nanoparticles with high heating capacity are needed. In addition, the influence of physiological factors on the heat capacity of a material should be investigated in order to determine the feasibility. In this study, magnetite nanoparticles coated with lauric acid were prepared by co-precipitation of Fe³⁺:Fe²⁺ in a ratio of 2:1, 5:3, 3:2, and 4:3, and the pH was controlled using NaOH. Structural and magnetization characterization by means of X-ray diffractometry (XRD) and a superconducting quantum interference device (SQUID) revealed that the main species was Fe₃O₄ and further showed that most of the nanoparticles exhibited superparamagnetic properties. All of the magnetic nanoparticles showed a specific absorption rate (SAR) increase that was linear with the magnetic field strength and frequency of the alternating magnetic field. Among all, the magnetic nanoparticles prepared in a 3:2 ratio showed the highest SAR. To further test the influence of physiological factors on the 3:2 ratio magnetic nanoparticles, we simulated the environment with protein (bovine serum albumin, BSA), blood sugar (dextrose), electrolytes (commercial norm-saline) and viscosity (glycerol) to examine the heating capacity under these conditions. Our results showed that the SAR value was unaffected by the protein and blood sugar environments. On the other hand, the SAR value was significantly reduced in the electrolyte environment, due to precipitation and aggregation with sodium ions. For the simulated viscous environment with glycerol, the result showed that the SAR values reduced with increasing glycerol concentration. We have further tested the heating capacity contribution from the Néel mechanism by trapping the magnetic nanoparticles in a solid form of polydimethylsiloxane (PDMS) to eliminate the heating pathway due to a Brownian motion. We measured the heating capability and determined that 47% of the total heat generated by the magnetic nanoparticles was from the Néel mechanism contribution. For evaluating magnetic nanoparticles, this method provides a fast and low cost method for determining qualitative and quantitative information measurement for the effect of physiological interference and could greatly reduce the cost and time by in vitro or animal test.     

Electron-hole coupling and the charge density wave transition in TiSe2

Angle-resolved photoemission is employed to measure the band structure of TiSe2 in order to clarify the nature of the ( 2 x 2 x 2) charge density wave transition. The results show a very small indirect gap in the normal phase transforming into a larger indirect gap at a different location in the Brillouin zone. Fermi surface topology is irrelevant in this case. Instead, electron-hole coupling together with a novel indirect Jahn-Teller effect drives the transition.     

Preparation of Zirconia Nanocrystals from Concentrated Zirconium Aqueous Solutions

A high concentration (0.8 M) zirconium solution turned into a stable aqueous colloid of about 60 nm in size upon low temperature (96^°C) incubation. Changing the acid concentration did not affect the colloidal growth rate nor the final colloid size much. However, the induction time before the rapid growth of colloidal particle could be altered. By limiting the incubation to just before the rapid growth of colloidal zirconia, and the addition of organic acids as surface modifiers, non-agglomerated primary crystallites (10 nm) of m-ZrO₂ could be recovered. These modified primary crystallites could then be repeatedly flocculated and redispersed in water by adjusting the pH.     

Propagation characteristics of a segmented cladding fiber

We propose a novel optical fiber design that consists of a uniform core and a segmented cladding formed by alternate regions of high and low refractive indices in the azimuthal direction. The structure is analyzed by use of the radial effective-index method, and the propagation characteristics of the structure are studied. The fiber has a highly dispersive cladding and shows characteristics similar to those of photonic-crystal fibers and holey fibers. The novel fiber offers the possibility of single-mode operation over a wide range of wavelengths with a large core diameter.     

First measurement of inclusive B→Xsη decays

We report a first measurement of inclusive B→Xsη decays, where Xs is a charmless state with unit strangeness. The measurement is based on a pseudoinclusive reconstruction technique and uses a sample of 657×10(6)BB pairs accumulated with the Belle detector at the KEKB e+e- collider. For MXs < 2.6 GeV/c2, we measure a branching fraction of [26.1±3.0(stat)-2.1+1.9(syst)-7.1+4.0(model)]×10(-5) and a direct CP asymmetry of ACP=-0.13±0.04-0.03+0.02. Over half of the signal occurs in the range MXs > 1.8 GeV/c2.     

Design and construction of a compact end-station at NSRRC for circular-dichroism spectra in the vacuum-ultraviolet region

A synchrotron‐radiation‐based circular‐dichroism end‐station has been implemented at beamline BL04B at the National Synchrotron Radiation Research Center (NSRRC) in Taiwan for biological research. The design and performance of this compact end‐station for measuring circular‐dichroism spectra in the vacuum‐ultraviolet region are described. The linearly polarized light from the beamline is converted to modulated circularly polarized light with a LiF photoelastic modulator to provide a usable wavelength region of 130–330 nm. The light spot at the sample position is 5 mm × 5 mm at a slit width of 300 µm and provides a flux greater than 1 × 10¹¹ photons s^?1 (0.1% bandwidth)^?1. A vacuum‐compatible cell made of two CaF₂ windows has a variable path length from 1.3 µm to 1 mm and a temperature range of 253–363 K. Measured CD spectra of (1S)‐(+)‐10‐camphorsulfonic acid and proteins demonstrated the ability of this system to extend the wavelength down to 172 nm in aqueous solution and 153 nm in hexafluoro‐2‐propanol.     

Observation of thermal-induced optical guiding and bistability in a mid-IR continuous-wave, singly resonant optical parametric oscillator

We report the observation of thermal-induced optical guiding and bistability in a mid-IR cw, singly resonant optical parametric oscillator (SRO) at approximately 3.2 microm. The SRO employs a MgO:PPLN crystal as the gain medium and a 1-nm-linewidth Yb-fiber laser at 1.064 microm as the pump source. As soon as the pump power reaches the thermal guiding threshold at 16.5 W, the SRO shows a step increase in the parametric efficiency by a factor of 2.5. At 25 W pump power, the SRO generated 5.3 and 1.2 W at 1.58 and 3.23 microm, respectively, with single-longitudinal-mode performance for the 3.23 microm radiation.     

Effect of graded triple delta-doped sheets on the performance of GaAs based dual channel pseudomorphic high electron mobility transistors

The characteristics of InGaP/InGaAs/GaAs dual channel pseudomorphic high electron mobility transistors (DCPHEMTs) with different graded triple delta-doped sheets are investigated and experimentally demonstrated. Based on a two-dimensional simulator of ATLAS, the band diagrams, electron densities and DC characteristics of studied devices are comprehensively analyzed. Due to the use of properly graded triple delta-doped sheets, good pinch-off and saturation characteristics, improved transport properties and wide current swing are obtained. For comparison, a practical DCPHEMT with good device performances is fabricated as well. It is found that the simulated data are in good agreement with experimental results.     

Comparison of CALIPSO and ground-based lidar profiles over Chung-Li, Taiwan

We report the first inter-comparison of vertical profiles of aerosols and clouds derived from space (CALIPSO) and ground based lidar over Chung-Li, Taiwan. Results show that inter-comparison is closer in case of aerosols than clouds. The strength/shortcoming of the comparison has been also discussed. An iterative calculation to retrieve extinction-to-backscatter ratio (lidar ratio) by using sun-photometer and CALIPSO data is also documented. By using the mentioned method, a mean lidar ratio of 23.5±8.2 sr was found. The derived lidar ratios are lower than former studies. The possible reasons for the difference have been discussed in this paper. The discussed methodology will be helpful to reduce the uncertainty of optical parameters derived from lidar data especially near the surface where the atmosphere is inhomogeneous.