80.5 MeV/u碳离子诱发铜靶的放射性剩余产物测量

高能重带电粒子能直接穿透靶原子核外电子层,与原子核发生直接碰撞,发生散裂反应,产生一系列具有放射性的剩余产物核.重带电粒子诱发靶材放射性剩余核与辐射防护和人员安全有着密切联系,当前,大部分剩余核产额主要依靠蒙特卡罗粒子输运程序进行模拟计算,其准确程度亟需通过实验测量进行准确评估.本文利用能量为80.5 MeV/u的(12)^C⁶⁺粒子对薄铜靶开展了辐照实验与伽玛射线测量,结合伽玛谱学分析方法,得出了辐照产生的18种放射性剩余产物的初始活度和产生截面值,并与PHITS模拟结果进行对比.结果表明,PHITS模拟程序对放射性剩余核种类的估计具有较高可靠性,在其绝对产额方面,与实验测量仍具有较大偏差.     

Cobalt Based Nanoparticles Embedded Reduced Graphene Oxide Aerogel for Hydrogen Evolution Electrocatalyst

Efficient water electrolysis catalyst is highly demanded for the production of hydrogen as a sustainable energy fuel. It is reported that cobalt derived nanoparticle (CoS₂, CoP, CoS|P) decorated reduced graphene oxide (rGO) composite aerogel catalysts for highly active and reliable hydrogen evolution reaction electrocatalysts. 7 nm level cobalt derived nanoparticles are synthesized over graphene aerogel surfaces with excellent surface coverage and maximal expose of active sites. CoS|P/rGO hybrid aerogel composites show an excellent catalytic activity with overpotential of ≈169 mV at a current density of ≈10 mA cm^?2. Accordingly, efficient charge transfer is attained with Tafel slope of ≈52 mV dec^?1 and a charge transfer resistance (R_ct) of ≈12 Ω. This work suggests a viable route toward ultrasmall, uniform nanoparticles decorated graphene surfaces with well‐controlled chemical compositions, which can be generally useful for various applications commonly requiring large exposure of active surface area as well as robust interparticle charger transfer.     

双掺(Tm3+,Tb3+)LiYF4激光器1.5 μm波长激光阈值分析

由速率方程推出了双掺（Tm^3 ,Tb^3 ）离子准四能级系统的激光阈值解析式，讨论了Tm^3 和Tb^3 离子之间的相互作用。分析了1.5μm波长附近的激光阈值和Tm^3 、Tb^3 离子的掺杂原子数分数及晶体长度的关系。结果表明，对于对应Tm^3 离子^3H4→^3F4跃迁的约1.5μm波长的激光，激活离子Tm^3 的掺杂原子数分数过大时，交叉弛豫作用将使系统阈值迅速增加。Tb^3 离子的加入，一方面能抽空激光下能级，起到降低阈值的作用；另一方面亦减少了激光上能级的寿命，使阈值升高。故Tb^3 离子有最佳掺杂原子数分数。对于Tm原子数分数为y=0.01的Tm:LiYF4晶体，Tb^3 离子的最佳掺杂原子数分数为0.002左右，同时表明，激光阈值与晶体长度有关。最佳晶体长度与Tm^3 、Tb^3 离子的掺杂原子数分数以及晶体的衍射损耗和吸收损耗有关。     

电路过渡过程的计算机辅助分析

电路过渡过程所列方程是微分方程，本文中采用的是方框图模型分析法，即将微分方程的复杂示解分解成最基本的加（减）、乘（除）、积分（微分）、增益等运算，采用VB设计用户界面产进行计算，并给出了一算例。     

Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.     

Ag+掺杂的立方相Y2O3:Eu纳米晶体粉末发光强度研究

采用化学自燃烧法制备了不同Ag⁺掺杂浓度的Y₂O₃:Eu纳米晶体粉末样品(［Y³⁺］∶［Eu³⁺］∶［Ag⁺］=99∶1∶X，X=0—3.5×10^-2)，以及通过退火处理得到了相应的体材料.根据X射线衍射谱确定所得纳米和体材料样品均为纯立方相.实验表明在纳米尺寸样品中随着Ag离子浓度的增加，荧光发射强度随之增加，当X=2×10^-2时达到最大值，其发光强度比X=0时提高了近50%.当Ag离子浓度继续增加，样品发光强度保持不变.在相应的体材料样品中则没有观察到此现象.通过对各样品的发射光谱，激发光谱，X射线衍射图谱，透射电镜(TEM)照片和荧光衰减曲线的研究，分析了引起纳米样品荧光强度变化的原因是由于Ag离子与表面悬键氧结合，从而使这一无辐射通道阻断，使发光中心Eu³⁺的量子效率提高；Ag⁺的引入所带来的另一个效应是使激发更为有效.这两方面原因使发光效率得到了提高.     

Scanning tunnelling microscope studies of growth of RuO2（110） thin layer on Ru（0001）

This paper reports that the growth of RuO_x(110) thin layer growth on Ru(0001) has been investigated by means of scanning tunnelling microscope (STM). The STM images showed a domain structure with three rotational domains of RuO_x(110) rotated by an angle of 120℃. The as-grown RuO_x(110) thin layer is expanded from the bulk-truncated RuO_x(110) due to the large mismatch between RuO_x(110) and the Ru(0001) substrate. The results also indicate that growth of RuO_x(110) thin layer on the Ru(0001) substrate by oxidation tends first to formation of the Ru-O (oxygen) chains in the [001] direction of RuO_x(110).