Soot formation characteristics in a lab-scale turbulent pulverized coal flame with simultaneous planar measurements of laser induced incandescence of soot and Mie scattering of pulverized coal

Soot formation characteristics of a lab-scale pulverized coal flame were investigated by performing carefully controlled laser diagnostics. The spatial distributions of soot volume fraction and the pulverized coal particles were measured simultaneously by laser induced incandescence (LII) and Mie scattering imaging, respectively. In addition, the radial distributions of the soot volume fraction were compared with the OH radical fluorescence, gas temperature and oxygen concentration obtained in our previous studies [1], [2]. The results indicated that the laser pulse fluence used for LII measurement should be carefully controlled to measure the soot volume fraction in pulverized coal flames. To precisely measure the soot volume fraction in pulverized coal flames using LII, it is necessary to adjust the laser pulse fluence so that it is sufficiently high to heat up all the soot particles to the sublimation temperature but also sufficiently low to avoid including a too large of a change in the morphology of the soot particles and the superposition of the LII signal from the pulverized coal particles on that from the soot particles. It was also found that the radial position of the peak LII signal intensity was located between the positions of the peak Mie scattering signal intensity and peak OH radical signal intensity. The region, in which LII signal, OH radical fluorescence and Mie scattering coexisted, expanded with increasing height above the burner port. It was also found that the soot formation in pulverized coal flames was enhanced at locations where the conditions of high temperature, low oxygen concentration and the existence of pulverized coal particles were satisfied simultaneously.     

Three-dimensional strain localization of water-saturated clay and numerical simulation using an elasto-viscoplastic model

Since strain localization is a precursor of failure, it is an important subject to address in the field of geomechanics. Strain localization has been analysed for geomaterials by several researchers. Many of the studies, however, treated the problems brought about by strain localization as two-dimensional problems, although the phenomena are generally three-dimensional. In the present study, undrained triaxial compression tests using rectangular specimens and their numerical simulation are conducted in order to investigate the strain localization behaviour of geomaterials under three-dimensional conditions. In the experiments, both normally consolidated and over-consolidated clay samples are tested with different strain rates. Using the distribution of shear strain obtained by an image analysis of digital photographs taken during deformation, the effects of the strain rates, the dilation, and the over-consolidation on strain localization are studied in detail. The analysis method used in the numerical simulation is a coupled fluid-structure finite element method. The method is based on the finite deformation theory, in which an elasto-viscoplastic model for water-saturated clay, which can consider structural changes, is adopted. The results of the simulation include not only the distribution of shear strain on the surfaces of the specimens, but also the distributions of strain, stress, and pore water pressure inside the specimens. Through a comparison of the experimental results and the simulation results, the mechanisms of strain localization are studied under three-dimensional conditions.     

The nonexistence of expansive homeomorphisms of a class of continua which contains all decomposable circle-like continua

A homeomorphism of a compactum with metric is expansive if there is such that if and , then there is an integer such that . It is well-known that -adic solenoids () admit expansive homeomorphisms, each is an indecomposable continuum, and cannot be embedded into the plane. In case of plane continua, the following interesting problem remains open: For each , does there exist a plane continuum so that admits an expansive homeomorphism and separates the plane into components? For the case , the typical plane continua are circle-like continua, and every decomposable circle-like continuum can be embedded into the plane. Naturally, one may ask the following question: Does there exist a decomposable circle-like continuum admitting expansive homeomorphisms? In this paper, we prove that a class of continua, which contains all chainable continua, some continuous curves of pseudo-arcs constructed by W. Lewis and all decomposable circle-like continua, admits no expansive homeomorphisms. In particular, any decomposable circle-like continuum admits no expansive homeomorphism. Also, we show that if is an expansive homeomorphism of a circle-like continuum , then is itself weakly chaotic in the sense of Devaney.

     

Rate-determining process in chemical vapor deposition of SiC on off-axis -SiC

Homoepitaxial growth on off-axis α-SiC at reduced pressures in a horizontal cold-wall chemical vapor deposition (CVD) system operating at has been investigated. The growth rate was found inversely proportional to the square root of total pressure or the partial pressure of H₂, a carrier gas. A model to explain the experimental results is proposed, where the rate-determining process in CVD is competition between Si species and hydrogen atoms for C (carbon) dangling bonds at SiC step edges.     

Temperature-controlled photosensitization properties of benzophenone-conjugated thermoresponsive copolymers

We previously found that a copolymer, poly(NIPAM- co-BP), consisting of N-isopropylacrylamide (NIPAM) and benzophenone (BP) units, behaves as a photosensitizer showing temperature-controlled oxygenation activity by singlet oxygen ( (1)O 2) in water ( J. Am. Chem. Soc. 2006, 128, 8751-8753 ). This polymer shows a heat-induced oxygenation enhancement at <20 degrees C, while showing suppression at >20 degrees C. This is driven by a heat-induced phase transition of the polymer from coil to micelle and then to globule state, controlling the stability and diffusion of (1)O 2 and the location of substrate. In the present work, effects of polymer concentration and BP content of the polymer on the oxygenation activity were studied at 5-35 degrees C. Increase in the polymer concentration leads to activity decrease at >20 degrees C due to strong polymer aggregation, suppressing incident light absorption of the BP units. With a decrease in BP content of the polymer, heat-induced oxygenation enhancement at <20 degrees C is more pronounced because formation of small size micelles accelerates (1)O 2 oxygenation. The obtained findings reveal that the polymer with low BP content, when used at high concentration, shows clear-cut off- on- off activity change against the temperature window: very low activity at <5 degrees C and >25 degrees C, and very high activity at middle temperature range.     

Development of pyrrole-imidazole polyamide for specific regulation of human aurora kinase-A and -B gene expression

Pyrrole-imidazole polyamide (PIP) is a nuclease-resistant novel compound that inhibits gene expression through binding to the minor groove of DNA. Human aurora kinase-A (AURKA) and -B (AURKB) are important regulators in mitosis during the cell cycle. In this study, two specific PIPs (PIP-A and PIP-B) targeting AURKA and AURKB promoter regions were designed and synthesized, and their biological effects were investigated by several in vitro assays. PIP-A and PIP-B significantly inhibited the promoter activities, mRNA expression, and protein levels of AURKA and AURKB, respectively, in a concentration-dependent manner. Moreover, 1:1 combination treatment with both PIPs demonstrated prominent antiproliferative synergy (CI value [ED(50)] = 0.256) to HeLa cells as a result of inducing apoptosis-mediated severe catastrophe of cell-cycle progression. The novel synthesized PIP-A and PIP-B are potent and specific gene-silencing agents for AURKA and AURKB.     

Energy-saving drying technology for porous media using liquefied DME gas

Process design and energy requirement for a practical plant are investigated for an energy-saving drying (dewatering) process invented by the authors in 2002 for high-moisture porous materials. The basic concept of the process involves the extraction of water from a high-moisture porous material by bringing it in physical contact with liquefied dimethyl ether (DME) at room temperature. Water content of DME asymptotically increases to the saturation value and the high-moisture porous material is dried almost perfectly. DME from the DME-water mixture is vaporized by decompression. DME and water are separated by flash distillation. DME vapor is compressed and cooled in a heat exchanger, and the latent heat of condensation is reused to vaporize the DME in the heat exchanger. Multistage compression and multistage flash distillation are employed. After compression, the temperature of DME is less than 50?°C. Because specific heat ratio of DME is only 1.11, the energy consumption of the compressor is reduced. Considering the adiabatic efficiency of the compressor and the net thermal efficiency, the total energy for dewatering is about 1100 kJ per 1-kg-water-content of the material being dewatered This process has significant potential and is compact than the existing dewatering processes.     

Characterization of atenolol transformation products on light-activated TiO2 surface by high-performance liquid chromatography/high-resolution mass spectrometry

We have studied the photocatalytic transformation of atenolol, 4-[2-hydroxy-3-[(1-methyl)amino]propoxyl]benzeneacetamide, a cardioselective beta-blocking agent used to treat cardiac arrhythmias and hypertension, under simulated solar irradiation using titanium dioxide as photocatalyst. The investigation involved monitoring drug decomposition, identifying intermediate compounds, assessing mineralization, and evaluating toxicity. High-performance liquid chromatography (HPLC) coupled to high-resolution mass spectrometry (HRMS) via an electrospray ionization (ESI) interface was a powerful tool for the identification and measurement of the degradation products; 23 main species were identified. Intermediates were characterized through their chromatographic behavior and evolution kinetics, coupled with accurate mass information. Through the full analysis of MS and MS(n) spectra and a comparison with parent drug fragmentation pathways, the diverse isomers were characterized. Neither atenolol nor the intermediates formed exhibit acute toxicity. All intermediates are easily degraded and no compound identified could withstand 2 h irradiation. Photomineralization of the substrate in terms of carbon mineralization and nitrogen release was rapid and, within 4 h of irradiation, organic nitrogen and carbon were completely mineralized.     

An efficient unnatural base pair for PCR amplification

Expansion of the genetic alphabet by an unnatural base pair system provides a powerful tool for modern biotechnology. As an alternative to previous unnatural base pairs, we have developed a new pair between 7-(2-thienyl)imidazo[4,5-b]pyridine (Ds) and 2-nitropyrrole (Pn), which functions in DNA amplification. Pn more selectively pairs with Ds in replication than another previously reported pairing partner, pyrrole-2-carbaldehyde (Pa). The nitro group of Pn efficiently prevented the mispairing with A. High efficiency and selectivity of the Ds-Pn pair in PCR amplification were achieved by using a substrate mixture of the gamma-amidotriphosphate of Ds and the usual triphosphates of Pn and the natural bases, with Vent DNA polymerase as a 3' to 5' exonuclease-proficient polymerase. After 20 cycles of PCR, the total mutation rate of the Ds-Pn site in an amplified DNA fragment was approximately 1%. PCR amplification of DNA fragments containing the unnatural Ds-Pn pair would be useful for expanded genetic systems in DNA-based biotechnology.