Flexizyme‐Mediated Genetic Reprogramming As a Tool for Noncanonical Peptide Synthesis and Drug Discovery

Noncanonical peptides occur frequently in Nature, and often display high bioactivity. However, the lack of tractable systems for the synthesis of diverse libraries of such peptides has thus far hampered their development as drugs. Genetic reprogramming techniques, in which noncanonical amino acids may be incorporated into peptides, have largely removed this limitation. This Concept article outlines the development of these techniques with an emphasis on drug discovery.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Ultrasonic-Combined Plasma Bubbling for Adherent Bacteria Disinfection on Medical Equipment

Plasma Chemistry and Plasma Processing - Atmospheric low-temperature plasma has received attention for application in disinfection methods. In this study, we develop a plasma bubbling method as a...     

18O/16O-Encoding Strategy for Microscale Stereochemical Determination of Peptidic Natural Products

The demand for more efficient methods of establishing the undetermined stereochemistries of peptidic natural products continues unabated. A new method for microscale stereochemical determination was devised by integrating solid-phase synthesis, split-and-mix randomization, ¹⁸O/¹⁶O-encoding of d /l -configurations, tandem mass spectrometry, and biological evaluation. Here we applied gramicidin A as the molecule for a blind test. Gramicidin A and its 31 diastereomers were randomly prepared in microgram scale with ¹⁸O/¹⁶O-stereochemical encoding and subjected to MS/MS-structural determination and cytotoxicity assay. Only the parent gramicidin A was selected from among the 32 stereoisomers, validating the high reliability of the present strategy.     

Dispersion of Carbon Nanotubes with “Green” Detergents

Solubilization of carbon nanotubes (CNTs) is a fundamental technique for the use of CNTs and their conjugates as nanodevices and nanobiodevices. In this work, we demonstrate the preparation of CNT suspensions with “green” detergents made from coconuts and bamboo as fundamental research in CNT nanotechnology. Single-walled CNTs (SWNTs) with a few carboxylic acid groups (3–5%) and pristine multi-walled CNTs (MWNTs) were mixed in each detergent solution and sonicated with a bath-type sonicator. The prepared suspensions were characterized using absorbance spectroscopy, scanning electron microscopy, and Raman spectroscopy. Among the eight combinations of CNTs and detergents (two types of CNTs and four detergents, including sodium dodecyl sulfate (SDS) as the standard), SWNTs/MWNTs were well dispersed in all combinations except the combination of the MWNTs and the bamboo detergent. The stability of the suspensions prepared with coconut detergents was better than that prepared with SDS. Because the efficiency of the bamboo detergents against the MWNTs differed significantly from that against the SWNTs, the natural detergent might be useful for separating CNTs. Our results revealed that the use of the “green” detergents had the advantage of dispersing CNTs as well as SDS.     

Selective decomposition of proteins by photocatalytic Ti(IV)-doped calcium hydroxyapatite particles from mixed-protein systems

The decomposition of protein molecules from a mixed-protein solution on the surface of calcium hydroxyapatite (CaHap) and Ti(IV)-doped CaHap (TiHap) particles with a Ti/(Ca + Ti) atomic ratio (X _Ti) of 0.10 and 0.20 under UV irradiation of 365 nm in wavelength was investigated. Acidic bovine serum albumin (BSA) and basic lysozyme (LSZ) were employed as a model of pathogenic proteins. The photocatalytic activities of TiHap particles were estimated from the decomposition of BSA and LSZ from the BSA (2.5 mg/cm³)–LSZ(1.0 mg/cm³) mixture under 1 mW/cm² UV irradiation dispersed in a 10-mL quartz tube. No change in BSA concentration by UV irradiation was observed for all the unheated original CaHap and TiHap particles without and with low photocatalytic activities, respectively. Similar results were observed for the systems that employed heat-treated particles endowed a high photocatalytic activity by heat treatment at 650 °C for 1 h. On the other hand, a selective photocatalytic decomposition was observed for the LSZ, i.e., only LSZ molecules were decomposed completely from the BSA (2.5 mg/cm³)–LSZ(1.0 mg/cm³) mixture by using heat-treated TiHap particles with X _Ti?=?0.10 and 0.20. This selective decomposition by TiHap particles was interpreted by higher adsorption affinity of positively charged LSZ to highly negatively charged TiHap together with low molecular weight and rigid structure of LSZ molecules.     

Ordered nanostructured ceramic–metal composites through multifunctional block copolymer-metal nanoparticle self-assembly

A novel strategy for fabrication of ordered ceramic–metal nanocomposites was demonstrated by multifunctional block copolymer/metal nanoparticle self-assembly. Hybrid organic–inorganic block copolymer poly(3-methacryloxypropyl-T8-heptaisobutyl-polyhedral oligomeric silsesquioxane-block-N,N-dimethylaminoethyl methacrylate) was synthesized and used as a bi-functional structure directing agent for ligand-stabilized platinum nanoparticles to form ordered organic–inorganic nanocomposites with dense loading of inorganic species in both microphase separated domains. Subsequently, thin films of the hybrid material were converted to ordered silica (ceramic)–platinum (metal) nanocomposites via UV-assisted ozonolysis. This is the first time ordered ceramic–metal nanocomposites were achieved through a bottom-up approach, opening up opportunities for the design and synthesis of a broad range of ordered inorganic–inorganic nanocomposites.