Effect of sonication on the photo-catalytic mineralization of some chlorinated organic compounds

Effects of the irradiation of ultrasound (US) on the photo-catalytic mineralization of some chlorinated organic compounds such as dichloroethane, tri- and tetrachloroethylenes, chloroacetic acids and chloromethanes were examined in oxygen saturated aqueous solutions suspended titanium dioxide (P25) particles. The yields of the sonochemical mineralization for these compounds were found to be extremely low compared to the photo-catalysis. However, the pre-sonication, US irradiation on the sample solution before the photo-irradiation, enhanced significantly the following photo-catalytic degradation to the complete oxidation. The effect was investigated in detail and it was found that the effect was mainly owing to the increase in the capability of the catalysis of which particles were sparsely dispersed by the sonication. The other contribution of the pre-sonication effect was found to be "pre-sonolysis", the initial formation of some intermediated products sonochemically, which are oxidizable more rapidly further to carbon dioxide than the original compound by the following photo-catalytic reactions. The pre-sonolysis effect was observed remarkably for trichloroacetic acid and tetrachloromethane, both of which are known to be hardly reactive to the photo-catalytic degradation. The photo-catalytic degradation with simultaneous sonication were also carried out for these compounds. The synergetic effect in the mineralization was observed both for carbontetrachloride and for trichloroacetic acid, the higher carbon dioxide yield being obtained in the simultaneous reaction than the sum of the yields in the photo-catalysis and the sonolysis each alone, while no significant synergetic effect was observed in the mineralization of other compounds.     

A concise route to (+)-lactacystin

A facile chromatography-free route to Kang's intermediate for the synthesis of (+)-lactacystin, a potent proteasome inhibitor, has been developed starting with Brown's asymmetric crotylation of tert-butyl 5-formyl-2,2-dimethyl-1,3-dioxan-5-ylcarbamate, easily available from 2-amino-2-(hydroxymethyl)propane-1,3-diol (Tris).     

Elastic friction drive of surface acoustic wave motor

Importance of elastic deformation control to obtain large output force with a surface acoustic wave (SAW) motor is discussed in this paper. By adding pre-load to slider, stator and slider surfaces are deformed in a few tens nanometer. Appropriate deformation in normal direction against normal vibration displacement amplitude of SAW existed. By moderate deformation, the output force of the SAW motor was enlarged up to about 10 N and no-load speed was 0.7 m/s. To produce this performance, the transducer weight and slider size were only 4.2 g and 4 x 4 mm(2).By traveling wave propagation, surface particles of the SAW device move in elliptical motion. Due to the amplitude of the elliptical motion is 10 or 20 nm order, the contact condition of the slider is very critical. To control the contact condition, namely, the elastic deformation of the slider and stator surface in nanometer order, a lot of projections were fabricated on the slider surface. The projection diameter was 20 micro m. In static condition, the elastic deformation and stress were evaluated with the FEM analysis. From this calculation and the simulation result, it is consider that the wave crest is distorted, hence the elasticity has influence on the friction drive condition.Elastic deformation of the stator surface beneath the projection from the initial position were evaluated. In 4 x 4 mm(2) square area, the sliders had from 1089 to 23,409 projections. Depression was independent to the contact pressure. However, the output force depended on the depression although the projection density were different. From the view point of the output power of the motor, the proper depression was independent to the projection density. Around 25 nm depression, the output force and output power were maximized. This depression value was almost same as the vibration displacement amplitude of the stator transducer.     

Diastereoselective photochromism of a bisbenzothienylethene governed by steric as well as electronic interactions

Introduction of an asymmetric center to C-2 of one of the benzothiophene rings of bisbenzothienylperfluorocyclopentene results in a highly diastereoselective photochromic system. The stereogenic center bears a hydrogen atom, a methyl group, and a methoxymethoxy group. The steric as well as the electronic repulsions gave an 87-88% diastereomer excess in various solvents at room temperature with 80-85% conversion to the colored form. The enantioselective synthesis was also carried out. Upon photoirradiation in hexane, a change in optical rotation at 820 nm, where neither the open form nor the colored form absorbs light, was observed repeatedly.     

Congruence of Siegel modular forms and special values of their standard zeta functions

In this paper, we consider the relationship between the congruence of cuspidal Hecke eigenforms with respect to Sp _n (Z) and the special values of their standard zeta functions. In particular, we propose a conjecture concerning the congruence between Saito-Kurokawa lifts and non-Saito-Kurokawa lifts, and prove it under certain condition. Partially supported by Grant-in-Aid for Scientific Research C-17540003, JSPS.     

A certain Dirichlet series of Rankin-Selberg type associated with the Ikeda lifting

We consider a certain Dirichlet series of Rankin-Selberg type associated with two Siegel cusp forms of the same integral weight with respect to Spn(Z). In particular, we give an explicit formula for the Dirichlet series associated with the Ikeda lifting of cuspidal Hecke eigenforms with respect to SL₂(Z). We also comment on a contribution to the Ikeda's conjecture on the period of the lifting.