Triggered single-photon emission and cross-correlation properties in InAlAs quantum dot

Triggered single-photon generation from InAlAs quantum dot (QD) was demonstrated for the first time. Emitted photon energy coincides with high detection efficiency range of Si single-photon detectors, which is highly suitable for free-space communication. Single-QD spectroscopy and crossed photon correlation measurements unambiguously revealed that several emitting lines observed in a single mesa structure originated from the identical QD, and two temporary competing decay processes associated with neutral states and charged states were identified. Presence of the competing process is also inferred from an analysis of steady-state photoluminescence intensities. Formation process of charged exciton in QD is also discussed.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Multiple reflections of Lamb waves at a delamination

Wave propagation in laminated plates with delaminations was calculated using the semi-analytical finite element method. The visualization results and deeper numerical analyses revealed the following phenomena on the fundamental Lamb modes at delamination regions of laminated plates. First, Lamb wave propagates toward the delamination, and then splits into two independent waves at the "Entrance" of the delamination with no significant reflections. These two waves reach the "Exit" of the delamination with the different phases and arrival time. Thus reflected and transmitted waves are excited at the Exit. The repetition of such reflections at the Exit causes the multiple reflections at regular intervals corresponding to the delamination size.     

Acoustic characteristics of Ni–Nb–Zr–H glassy alloys by ultrasonic shear waves

The propagation characteristics of shear horizontally polarized (SH) waves passing through (Ni₄₂Nb₂₈Zr₃₀)_100–x H_x (x = 0–15.2) glassy alloys were investigated as a function of hydrogen content. With an increase in hydrogen content, the propagation time and main frequency of the receiving waves show increase and decrease, respectively, indicating expan‐ sion in average atomic distance which comes from solution of hydrogen. In sharp contrast to crystalline alloys, the decrease in damping ratio and the delay in phase with increasing hydrogen suggest a strong settlement of hydrogen into four‐coordination sites surrounded tetrahedrally by four Zr atoms and the resulting increase in dynamic elasticity, respectively. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Reconstruction of the acoustic impedance profile in a plate using an inverse spectral procedure

An inverse spectral procedure was applied to reconstruct the acoustic impedance profile along the thickness direction of a plate using its thickness resonance frequencies, density and thickness. For a successful reconstruction, the material-property profile must be symmetric about the mid-plane of the plate. Several cases of numerical simulations, including plates with a few layers and with a high number of layers are described. The calculated resonance frequencies were used to reconstruct the acoustic impedance profile, a process that was successful for all cases. We assume that a plate with a high number of layers, each with a different but constant acoustic impedance, simulates a plate with a smoothly varying acoustic impedance profile. It can be concluded that such a plate, which generates small, virtually undetectable, internally reflected waves, can also be reconstructed. In the special case of a plate of unknown thickness and unknown but constant density, the method is still useful, because a relative variation of the material property can be reconstructed using only the resonance frequencies. An experiment using a resonance-mode electromagnetic acoustic transducer (resonance-mode EMAT) is also described. EMAT is a non-contact ultrasonic method that can measure thickness resonance frequencies, making it appropriate for this method. Some examples of applications are measurement of the temperature profile inside a rolled metal sheet, measurement of a clad metal plate, and monitoring of a metal casting.     

Study of Si(0 0 1)4 × 2-Ga structure by scanning tunneling microscopy and ab initio calculation

We have studied Si(0 0 1)-Ga surface structures formed at Ga coverages of slightly above 0.50 monolayer (ML) at 250 °C by scanning tunneling microscopy (STM). 4 × 2-, 5 × 2-, and 6 × 2-Ga structures were observed in a local area on the surface. The 4 × 2-Ga structure consists of three protrusions, as observed in filled- and empty-state STM images. The characters of these structures are clearly different from those of other Si(0 0 1)-Ga structures. We also performed an ab initio calculation of the energetics for several possible models for the 4 × 2-Ga structure, and clarified that the three-orthogonal-Ga-dimer model is the most stable. Also, the results of comparing the simulated STM images and observation images at various bias voltages indicate that this structural model is the most favorable.     

Flow characteristics of pressure reducing valve with radial slit structure for low noise

Pressure reducing valves are widely used to maintain the pressure of gas reservoirs to specific values. In a normal valve, supply pressure is decompressed with an orifice structure. When compressed air passes through the orifice structure, considerable noise occurs at the downstream side. In this paper, we have developed a radial slit structure that can reduce pressure without noise. The noise is reduced by changing the orifice structure into the radial slit structure. The radial slit structure valve reduces pressure without noise by suppressing the generation of turbulence and shock wave at the downstream. The analysis of the flow in radial slit structure was achieved by CFD2000 software. The flow rate and pressure distribution were simulated and compared with the experimental result. To confirm the generation of shock wave, the flow of orifice and radial slit structure at the downstream was visualized by Schlieren photography method. A shock wave was generated in the orifice structure, but no shock wave was generated in the radial slit structure. Noise reduction efficiency was investigated by the experiment. The experiment apparatus was set up to JIS standards. The experimental results indicated that the noise level decreased by approximately 40 dB in the slit structure. It is confirmed that the radial slit structure has effectiveness for low noise in the pressure reducing flow. And, it is expected that it can be applied to various kinds of industrial fields.