Dynamic mechanical analysis

Using dynamic mechanical analysis (DMA) we have studied thermal degradation for a system containing a diglycidyl ether of bisphenol A (DGEBA) and 1,3-bisaminomethylcylohexane (1,3-BAC). The changes of dynamic mechanical properties during thermal degradation indicated a shift of the glass transition temperature (T _g) to higher temperatures and a decrease in the peak value of the dynamic loss factor (tan δ) with an increasing of aging time. The value of dynamic storage modulus (E′) at the rubbery state showed an increase with aging time, whiteE′ at the glassy state only underwent a moderate change with increased thermal degradation. From these results it can be argued that thermal degradation during the stage prior to the onset of the severe degradation involves structural changes in the epoxy system, as further crosslinking and loss of dangling chains in the crosslinked network.     

Use of new composite materials for the determination of Cu, Cd, Mo, As, and Sb in biological samples by radiochemical neutron activation analysis

Summary  Vezetéknév     

Local solution for the Kadomtsev-Petviashvili equation with periodic conditions

In this article we prove a local existence and uniqueness theorem for the Kadomtsev-Petviashvili Equation (u _t +u _xxx +uu _x ) _x −u _yy =0) in the Sobolev spaces of orders≥3, with initial values in the same spaces, and periodic boundary conditions. This theorem improves previous results based upon the application of singular perturbation techniques.     

Mössbauer spectroscopic study of Prussian Blue from different provenances

Ferric ferrocyanides synthesized from different sources of ferric cations and ferrocyanide anions and those derived from ferrous ferricyanide, ferrous ferrocyanide and ferric ferricyanide have been studied using Mössbauer and XRD techniques. Structural information of the effect of the provenance on the properties of the final compound is obtained. Significant correlations between isomer shift and quadrupole splitting of inner and outer iron cations have been observed.     

TDPAC study in ZnTiF6·6H2O between room temperature and 1273 K

Using the time differential perturbed angular correlation technique, the hyperfine interactions as titanium sites in ZnTiF6·6H₂O and its decomposition products were determined between room temperature (300 K) and 1273 K. The different steps in the decomposition pattern were identified and a simple model is given for it.     

Tuning inventory policy parameters in a small chemical company

A project to improve inventory management in a small UK chemical company is described. A research group comprising university academics and company managers for logistics and information technology examined current practices and analysed a database of historical records of business operations of the company. Based on the analysis, a scheme to categorise stock and set ordering policies to optimise inventory costs was developed. Some comments are made on process issues and the learning that took place.     

On the evaluation of the nonisothermal kinetic parameters of (GeS2)0.3(Sb2S3)0.7 crystallization using the IKP method

The isoconversional method suggested by Friedman and the invariant kinetic parameters method (IKP) were used in order to examine the kinetics of the nonisothermal crystallization of (GeS₂)_0.3(Sb₂S₃)_0.7. The objective of the paper is to show the usefulness of the IKP method both for determining the activation parameters as well as the model of the investigated process. It was shown that the kinetic triplet [(E, A, f(α), where E is the activation energy, A is the preexponential factor, and f(α) is the differential function of conversion], which results through the application of the IKP method, depends on the set of kinetic models considered. For different sets of kinetic models, proportional values of f(α) are obtained. A criterion for the selection of this set, the use of which lead to the true kinetic triplet corresponding to the analyzed process (E = 163.2 kJ mol^?1; A = 2.47 × 10¹² min^?1 and the Avrami‐Erofeev model, A_m, for m = 2.5–2.6 was suggested. © 2004 Wiley Periodicals, Inc. Int J Chem Kinet 36: 309–315, 2004     

One‐step synthesis of aminopyrimidines from 5‐Oxo‐4H‐benzopyrans

Novel 4‐amino‐6‐aryl‐2‐phenylpyrimidine‐5‐carbonitriles have been prepared in one step procedure from the readily available 4‐aryl‐2‐amino‐3‐cyano‐5,6,7,8‐tetrahydro‐7,7‐dimethyl‐5‐oxo‐4H‐benzopyrans. The mass spectroscopy study under EI conditions shows molecular peaks with high intensity corresponding to the loss of benzonitrile from the C2 position of the pyrimidine ring. Semiempirical (AMI and PM3) and ab initio HF/6–31G* calculations reveal a favored distorted geometry where the three rings are not in the same plane.     

Click chemistry in materials synthesis. III. Metal‐adhesive polymers from Cu(I)‐catalyzed azide–alkyne cycloaddition

1,2,3‐Triazole‐based polymers generated from the Cu(I)‐catalyzed cycloaddition between multivalent azides and acetylenes are effective adhesive materials for metal surfaces. The adhesive capacities of candidate mixtures of azide and alkyne components were measured by a modified peel test, using a customized adhesive tester. A particularly effective tetravalent alkyne and trivalent azide combination was identified, giving exceptional strength that matches or exceeds the best commercial formulations. The addition of Cu catalyst was found to be important for the synthesis of stronger adhesive polymers when cured at room temperature. Heating also accelerated curing rates, but the maximum adhesive strengths achieved at both room temperature and high temperature were the same, suggesting that crosslinking reaches the same advanced point in all cases. Polytriazoles also form adhesives to aluminum, but copper is bound more effectively, presumably because active Cu(I) ions may be leached from the surface to promote crosslinking and adhesion. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5182–5189, 2007     

Enthalpies of sorption of linear hydrocarbons (C2–C8) and chloroderivatives of methane and ethylene on the surface of hydrotalcite

Differential molar adsorption enthalpies (DMAE) were determined by gas chromatographic measurements of specific retention volume of vapors on the surface of two forms of Mg–Al hydrotalcite. A linear dependence of the DMAE on the number of the carbon atoms in hydrocarbons was observed for both form of hydrotalcite. The dependence of the differential molar adsorption enthalpies on the number of chlorine atoms in organic molecules is discussed. A linear dependence of DMAE on the molecular weight of chloroderivatives of methane and ethylene on the basic form in an order monochloromethane < dichloromethane < trichloromethane or vinylidene chloride < 1,1-dichloroethylene < trichloroethylene was found.