Fusion around the barrier for 7Li+12C

Fusion cross-sections for the ⁷Li + ¹²C reaction have been measured at energies above the Coulomb barrier by the direct detection of evaporation residues. The heavy evaporation residues with energies below 3 MeV could not be separated out from the α-particles in the spectrum and hence their contribution was estimated using statistical model calculations. The present work indicates that suppression of fusion cross-sections due to the breakup of ⁷Li may not be significant for ⁷Li + ¹²C reaction at energies around the barrier.     

Ultrafast X-ray science at the advanced light source

On May 19, 2004, 250 guests from all over the world joined the DESY research center to celebrate 40 years of research with synchrotron radiation at DESY in Hamburg. “The first measurements with the light beam from the DESY ring accelerator started in 1964. DESY was one of the seed laboratories in which the worldwide success story of research with synchrotron radiation began,” Albrecht Wagner, chairman of the DESY Board of Directors, explained in his welcoming address. “Today, more than 1,900 scientists from 31 countries come to DESY every year to carry out experiments with synchrotron radiation.”

Forty years ago, synchrotron radiation at DESY started from scratch. At the beginning of the 1960s, the radiation generated by the electrons in the bending magnets of their new 6 GeV electron synchrotron was regarded by DESY particle physicists as an unwanted, disruptive effect.     

Commercial grade aluminium: A versatile reactor flux monitor

With the advent of Ge(Li) spectrometry, a high standard of purity for neutron flux monitors no longer remains an imperative “must” and becomes rather superfluous. From this standpoint, commercial grade Al was investigated for its suitability as a reactor flux monitor and was found to have a much greater practical utility than most of the monitors reported. Three Al foils and one wire were randomly selected from four different commercial sources, and analysed for their Fe, Ga, Mn and Na contents by neutron activation and high-resolution gamma-spectrometry. While Na was found to have a very heterogeneous distribution, Fe, Mn and Ga concentrations in different splits of each type of Al were consistently uniform within ±2–3%. Eight possible monitor reactions on Al, Mn, Fe and Ga have been recommended as neutron flux integrators for all the 3 components of a reactor spectrum, viz. thermal, epithermal and fast, covering a wide range of flux levels from 10⁷ to 10¹⁴n·cm⁻²·sec⁻¹. The advantages and versatility of commercial grade Al as a pile neutron dosimeter are discussed.     

TOF-OFF: A method for determining focal positions in tightly focused free-electron laser experiments by measurement of ejected ions

Pulse intensities greater than 10¹⁷ Watt/cm² were reached at the FLASH soft X-ray laser in Hamburg, Germany, using an off-axis parabolic mirror to focus 15 fs pulses of 5–70 μJ energy at 13.5 nm wavelength to a micron-sized spot. We describe the interaction of such pulses with niobium and vanadium targets and their deuterides. The beam produced craters in the solid targets, and we measured the kinetic energy of ions ejected from these craters. Ions with several keV kinetic energy were observed from craters approaching 5 μm in depth when the sample was at best focus. We also observed the onset of saturation in both ion acceleration and ablation with pulse intensities exceeding 10¹⁶ W/cm², when the highest detected ion energies and the crater depths tend to saturate with increasing intensity.A general difficulty in working with micron and sub-micron focusing optics is finding the exact focus of the beam inside a vacuum chamber. Here we propose a direct method to measure the focal position to a resolution better than the Rayleigh length. The method is based on the correlation between the energies of ejected ions and the physical dimensions of the craters. We find that the focus position can be quickly determined from the ion time-of-flight (TOF) data as the target is scanned through the expected focal region. The method does not require external access to the sample or venting the vacuum chamber. Profile fitting employed to analyze the TOF data can extend resolution beyond the actual scanning step size.     

Model studies of colloidal silica precipitation using biosilica extracts from<Emphasis Type="Italic"> Equisetum telmateia</Emphasis>

Structural materials containing silicon are produced in single celled organisms through to higher plants and animals. Hydrated amorphous silica is a colloidal mineral of infinite functionality that is formed into structures with microscopic and macroscopic form. Proteins and proteoglycans are suggested to play a critical role in the catalysis of silica polycondensation and in structure direction during the formation of these magnificent structures. This article extends knowledge on the effect of protein containing biosilica extracts from Equisetum telmateia on the kinetics of silica formation and structure regulation. Utilising potassium silicon catecholate as the source of soluble silicon, bioextracts obtained from plant silica by dissolution of the siliceous phase with aqueous HF following extensive acid digestion of the plant cell wall were found to modify the kinetic rate constants for the formation of small silicic acid oligomers under circumneutral pH conditions and to modify the solubility of silicic acid in solution. Addition of the bioextracts at ca. 1 wt% to the reaction medium reduced the sizes and range of sizes of the fundamental silica particles formed and led to the formation of crystalline polymorphs of silica under conditions of ca. neutral pH, room temperature and in the absence of multiply charged cations, conditions assumed to be relevant to the biological mineralization environment. The ability of biological organisms to regulate the formation of silica structures with prevention of crystallinity is discussed as are the implications of this study in terms of the generation of new materials with specific form and function for industrial application.