Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.     

矩阵方程（A^TXA，B^TXB=（C，D）的反对称解及其最佳逼近

本利用矩阵对的标准相关分解，得到了矩阵方程(A^TXB，B^TXB)=(C，D)反对称解存在的充分必要条件及通解表达式，同时给出了解关于已知矩阵的最佳逼近．     

Influence of Turbid Medium Parameters on Back Scattered Intensity and Pulsewidth of Picosecond Pulse

In this paper, we simulate a practical in vivo technique in which is produced influence of turbid medium parameters on backscattered intensity and pulsewidth of picosecond for turbid tissue surface of a semiinfinite medium by a small narrow linewidth laser beams. It is shown that the interaction of the ultra short pulse and the turbid tissue is very used as researching the optical parameters of the turbid medium.     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Synthesis of graft copolymers with “V‐shaped” and “Y‐shaped” side chains via controlled radical and anionic polymerizations

A combination of nitroxide‐mediated radical polymerization and living anionic polymerization was used to synthesize a series of well‐defined graft (co)polymers with “V‐shaped” and “Y‐shaped” branches. The polymer main chain is a copolymer of styrene and p‐chloromethylstyrene (PS‐co‐PCMS) prepared via nitroxide‐mediated radical polymerization. The V‐shaped branches were prepared through coupling reaction of polystyrene macromonomer, carrying 1,1‐diphenylethylene terminus, with polystyryllithium or polyisoprenyllithium. The Y‐shaped branches were prepared throughfurther polymerization initiated by the V‐shaped anions. The obtained branches, carrying a living anion at the middle (V‐shaped) or at the end of the third segment (Y‐shaped), were coupled in situ with pendent benzyl chloride of PS‐co‐PCMS to form the target graft (co)polymers. The purified graft (co)polymers were analyzed by size exclusion chromatography equipped with a multiangle light scattering detector and a viscometer. The result shows that the viscosities and radii of gyration of the branched polymers are remarkably smaller than those of linear polystyrene. In addition, V‐shaped product adopts a more compact conformation in dilute solution than the Y‐shaped analogy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4013–4025, 2007     

Cu-MgF2复合纳米金属陶瓷薄膜的电导特性研究

用射频磁控共溅射法制备了Cu体积分数分别为 10 % ,15 % ,2 0 %和 3 0 %的Cu MgF2 复合金属陶瓷薄膜 .用x射线衍射、x射线光电子能谱和变温四引线技术对薄膜的微结构、组分及电导特性进行了测试分析 .微结构分析表明 :制备的Cu MgF2 复合薄膜由fcc Cu晶态纳米微粒镶嵌于主要为非晶态的MgF2 陶瓷基体中构成 ,Cu晶粒的平均晶粒尺寸随组分增加从 11 9nm增至 17 8nm .5 0— 3 0 0K温度范围内的电导测试结果表明 :当Cu体积分数qM 由 15 %增加到 2 0 %时 ,Cu MgF2 复合薄膜的电阻减小了 8个量级 ,得出制备的复合薄膜渗透阈qCM 应处于 15 %和 2 0 %之间 .qM 在 10 %和 15 %之间的薄膜呈介质导电状态 ,而在 2 0 %和 3 0 %之间的薄膜则呈金属导电状态 .从理论上讨论了复合薄膜中杂质电导和本征电导的激活能及其对电导的贡献 ,并讨论了Cu MgF2 复合纳米金属陶瓷薄膜的渗透阈 ,得到了和实验一致的结果     

求解非对称线性方程组的QMRGCGS方法

1 引言 求解非对称线性方程组Ax=b的双共轭梯度方法(BCG)[3]和它的变形共轭梯度平方方法(CGS)[6]都有典型的不规则收敛行为,后来Freund和Nachtigal提出一种BCG类方法,即拟极小剩余方法(QMR)[7],用来补救BCG方法的收敛性并且产生了光滑的收敛曲线。然而,象BCG方法一样,QMR方法要用到系数矩阵A及其转置A~T与向量的乘积,为了解决这一问题,Freund提出TFQMR方法,此方法具有拟极小剩余性,同时不需用到A~T与向量的乘积。     

Synthesis of side‐chain liquid‐crystalline homopolymers and triblock copolymers with p‐methoxyazobenzene moieties and poly(ethylene glycol) as coil segments by atom transfer radical polymerization and their thermotropic phase behavior

A series of side‐chain liquid‐crystalline (LC) homopolymers of poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] with different degrees of polymerization were synthesized by atom transfer radical polymerization (ATRP), which were prepared with a wide range of number‐average molecular weights from 5.1 × 10³ to 20.6 × 10³ with narrow polydispersities of around 1.17. Thermal investigation showed that the homopolymers exhibit two mesophases, a smectic phase, and a nematic phase, and the phase‐transition temperatures of the homopolymers increase clearly with increasing molecular weights. A series of novel LC coil triblock copolymers with narrow polydispersities was synthesized by ATRP, and their thermotropic phase behavior was investigated with differential scanning calorimetry and polarized optical microscopy. The LC coil triblocks were designed to have an LC conformation of poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] with a wide range of molecular weights from 3.5 × 10³ to 1.7 × 10⁴ and the coil conformation of poly(ethylene glycol) (PEG) (number‐average molecular weight: 6000 or 12,000) segment. Their characterization was investigated with ¹H NMR, Fourier transform infrared spectra, and gel permeation chromatography. Triblock copolymers exhibited a crystalline phase, a smectic phase, and a nematic phase. The phase‐transition temperatures from the smectic to nematic phase and from the nematic to isotropic phase increased, and the crystallization of PEG depressed with increasing molecular weight of the LC block. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2854–2864, 2003     

A modified Silver–Meal heuristic for dynamic lot sizing under incremental quantity discounts

This note presents a variation of the well-known Silver–Meal heuristic to deal with lot sizing under a combination of a known, but time-varying, demand pattern along with an incremental quantity discount structure. The heuristic is shown to perform very well on a set of experiments presented in a recent paper in this journal. Additional experiments are performed to further explore the time horizon effects on the relative performance of the newly proposed heuristic compared to the two best performing ones from the previous paper.     

Preparation of nanometer MgO by sol-gel auto-combustion

Nanometer MgO was prepared via a sol-gel auto-combustion technique using magnesium nitrate as raw material and citric acid as chelating agent. IR spectra of the dried gel were used to investigate the structure of the precursors. By studying the different TG curves of magnesium citrate gel prepared by different methods, we found that a combustion process occurred and the nitrate ions acted as an oxidant in the combustion process. TEM photographs of synthesized powders from the sol-gel auto-combustion showed that the crystallites were uniform in size. In addition, the XRD pattern of this sample showed that the particle size was 8.9 nm. The BET curves, in turn, showed that the specific surface of the sample was 26.34 m²/g. The mechanism of the frothing process in restraining agglomeration is discussed. __________ Translated from Journal of East China Normal University (Natural Science), 2007, (2): 52–57 [译自: 华东师范大学学报(自然科学版)]