Shape transition from InAs quantum dash to quantum dot on InP(3 1 1)A

We report on the shape transition from InAs quantum dashes to quantum dots (QDs) on lattice-matched GaInAsP on InP(3 1 1)A substrates. InAs quantum dashes develop during chemical-beam epitaxy of 3.2 monolayers InAs, which transform into round InAs QDs by introducing a growth interruption without arsenic flux after InAs deposition. The shape transition is solely attributed to surface properties, i.e., increase of the surface energy and symmetry under arsenic deficient conditions. The round QD shape is maintained during subsequent GaInAsP overgrowth because the reversed shape transition from dot to dash is kinetically hindered by the decreased ad-atom diffusion under arsenic flux.     

Control of the block copolymer morphology in templated epoxy thermosets

It has been found that by the addition of low concentrations of an amphiphilic block copolymer to an epoxy resin, novel disordered morphologies can be formed and preserved through curing. This article will focus on characterizing the influence of the block copolymer and casting solvent on the templated morphology achieved in the thermoset sample. The ultimate goal of this work is to determine the parameters that would control the microphase morphology produced. Epoxy resins blended with a series of amphiphilic block copolymers based on hydrogenated polyisoprene (polyethylene-alt-propylene or PEP) and polyethylene oxide (PEO), specifically, were investigated. In this article, the cure-induced order–order phase transition from the spherical to wormlike micelle morphology will also be discussed. It is proposed that the formation of the wormlike micelle structure from the spherical micelle structure is similar to the phase transition behavior that occurs in dilute block copolymer solutions as a function of the influence of the solvent on micelle morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3338–3348, 2007     

Interfacial structure and electrical properties of LaAlO3 gate dielectric films on Si by metalorganic chemical vapor deposition

LaAlO₃ (LAO) gate dielectric films were deposited on Si substrates by low-pressure metalorganic chemical vapor deposition. The interfacial structure and composition distribution were investigated by high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), secondary-ion mass spectroscopy (SIMS), and Auger-electron spectroscopy (AES). HRTEM confirms that there exists an interfacial layer between LAO and Si in most samples. AES, SIMS, and XPS analyses indicate that the interfacial layer is compositionally graded La–Al silicate and the Al element is severely deficient close to the Si surface. Electrical properties of LAO films were evaluated. No evident difference in electrical properties between samples with and without native SiO₂ layers was observed. The electrical properties are discussed in terms of LAO growth mechanisms, in relation to the interfacial structure. PACS 73.40.Qv; 81.15.Gh; 77.55.+f; 68.35.-p     

Pressure effects in a plastic columnar discotic triphenylene

The effect of hydrostatic pressure on the structure of a plastic columnar discotic triphenylene has been investigated. The goal was to determine whether pressure can be used to modify electronic properties via changes in structural properties of columnar discotics to any significant extent. The findings are that (i) the intra- and inter-columnar distances are reduced in a nearly isotropic fashion, (ii) that the crystal sizes are reduced and (iii) that a transition takes place from a more highly ordered plastic columnar to a less ordered hexagonal columnar state with increasing pressure. The induced decrease of the molecular distances, amounting to 6% for pressures up to 17 kbar, are clearly too small to induce an appreciable modification of the electronic structure and thus opto-electronic properties.     

Solid-State Thin-Film Sensors Based on Chalcogenide Materials Obtained by Planar Technology and Pulsed Laser Deposition

Methods of silicon planar technology and pulsed laser deposition were applied to fabricate fully solid-state chemical sensors for determining ions of copper, lead, cadmium, thallium, and also sulfide and chloride ions on the basis of thin chalcogenide films as ion-sensitive membranes.     

Control of a liquid–liquid heat exchanger

 The analytical solutions of equations describing the dynamics of distributed parameter systems are usually complicated in form and derivations and inconvenient to use for simulation and control system design. The liquid–liquid counter flow heat exchanger is an example of these disturbed parameter systems. An analytical solution of the dynamics of a symmetrically operated counter flow heat exchanger in the form of transfer function matrix is investigated in open-loop and close-loop conditions. The resulting non-linear model was linearized using perturbation approach. A feed-forward path controller to counteract at any disturbances in the boundary temperature and a non-interactive controller to decouple the outputs were implemented. Received on 22 February 2001 / Published online: 29 November 2001     

Synthesis and structure-activity relationships of N-substituted 2-[(2-imidazolylsulfinyl)methyl]anilines as a new class of gastric H+/K(+)-ATPase inhibitors.

A series of N-substituted 2-[(2-imidazolylsulfinyl)methyl]anilines (3) was synthesized and evaluated for its biological activity against gastric H+/K(+)-ATPase prepared from rabbit stomach and gastric acid secretions in Heidenhain pouch dogs. Monoalkyl substituents on the nitrogen atom of the aniline moiety markedly inhibited the enzyme activity to the same degree as omeprazole, a representative H+/K(+)-ATPase inhibitor. Most of these compounds, administered at 3 mg/kg i.v. inhibited histamine-stimulated gastric acid secretion. The inhibitory activity of these derivatives on the enzymes at pH 6.0 was more potent than that at pH 7.4, and was distinctly correlated to stability in aqueous solution at pH 5.0.     

Cathode spot energy transfer simulated by a focused laser beam

Minimum conditions for the formation of surface craters by laser irradiation were studied experimentally and theoretically for various metals. The critical power density for crater formation within 20 ns was about 10¹¹ W/m². It is therefore concluded that crater formation by ion bombardment requires an ion current density on the order of 10¹⁰ A/m²     

Two-fluid and population balance models for subcooled boiling flow

Population balance equations combined with a three-dimensional two-fluid model are employed to predict subcooled boiling flow at low pressure in a vertical annular channel. The MUSIG (MUltiple-SIze-Group) model implemented in the computer code CFX4.4 is further developed to accommodate the wall nucleation at the heated wall and condensation in the subcooled boiling regime. Comparison of model predictions against local measurements is made for the void fraction, bubble Sauter mean diameter and gas and liquid velocities covering a range of different mass and heat fluxes and inlet subcooling temperatures. Additional comparison using empirical relationships for the active nucelation site density and local bubble diameter is also investigated. Good agreement is achieved with the local radial void fraction, bubble Sauter diameter and liquid velocity profiles against measurements. However, significant weakness of the model is evidenced in the prediction of the vapour velocity. Work is in progress to circumvent the deficiency through the consideration of additional momentum equations or developing an algebraic slip model to account for bubble separation.