ON THE ACRIDINE AND THIAZINE DYE SENSITIZED PHOTODYNAMIC INACTIVATION OF LYSOZYME—SINGLET OXYGEN SELF-QUENCHING BY THE SENSITIZERS

Abstract— The quantum yield of the photodynamic inactivation of lysozyme increases in the sequence acridine orange, methylene blue, proflavine and acriflavine (1:5:6:12). At least up to protein concentrations of 0.1 m M , singlet oxygen is exclusively responsible for the inactivation of the enzyme. For methylene blue, acriflavine and proflavine the quantum yields decrease considerably with increasing dye concentrations. From measurements in H₂O and D₂O buffer solutions it was concluded that in the case of methylene blue the effect is mainly caused by the quenching of singlet oxygen [rate constant (3–4) × 10⁸ M ⁻¹ s⁻¹]. For the acridine sensitizers both singlet oxygen and dye triplet quenching processes have to be taken into consideration. It has been found that all sensitizers act as competitive inhibitors of the enzymatic reaction of lysozyme. However, the dye-protein interaction near the active center cannot be responsible for the observed dye self-quenching effect.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

Shear induced relaxation of polymer micelles at the solid-liquid interface

A 20% aqueous solution of (ethylene oxide) 99-(propylene oxide) 65-(ethylene oxide) 99, F127, was investigated by combining rheology in a cone/plate-geometry and surface-sensitive grazing incident neutron scattering. The crystalline structure formed by the polymer micelles becomes less pronounced for low shear rates, but correlations increase for higher shear rates. After stopping shear a slow relaxation of the micelles is found in the vicinity (50 mum thick layer) of a hydrophilic silicon wall (strong micelle-wall interaction), while a fast relaxation is observed in the boundary layer against the hydrophobic silicon wall (weak micelle-wall interaction). The results show that in the vicinity of the interface wall-particle interactions compete heavily with the shear force acting on the liquid.     

Microstructure of thermoelectric (Bi0.15Sb0.85)2Te3 film

The film of thermoelectric ternary p-type (Bi_0.15Sb_0.85)₂Te₃ was deposited on polyimide foil substrate at 168 °C using direct-current magnetron sputtering. Microstructural investigations of the film were performed by electron microscopy techniques. SEM observations showed that the film surface consisted of large-sized particulates with small-sized particles and also mound-like crystal agglomerates in some areas. Chemical composition of the film was analyzed using energy-dispersive X-ray spectrometer (EDS). It has been observed that the EDS results were in an agreement with nominal composition for the film. Detailed microstructural investigations were carried out using transmission electron microscopy (TEM). TEM images and selected area electron diffraction patterns showed that the film has randomly oriented polycrystalline grain structure. High-resolution TEM images indicated that the microstructure of film also contained nano-crystal structure, smaller than 10 nm.