Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

FI代数的滤子

研究FI代数的滤子理论，建立F滤子、P滤子、Q滤子、C滤子之间的联系．     

Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003     

正交变换在重积分中某些应用

正交变换是代数学的基本内容 ,其用途十分广泛 .重积分的计算往往存在技术性的困难 ,若利用“正交变换”的有关理论去解决某些重积分的计算问题是颇有功效的 .本文将以“正交变换”为工具 ,简洁的处理重积分的某些问题     

2‐connected 7‐coverings of 3‐connected graphs on surfaces

An m‐covering of a graph G is a spanning subgraph of G with maximum degree at most m. In this paper, we shall show that every 3‐connected graph on a surface with Euler genus k ≥ 2 with sufficiently large representativity has a 2‐connected 7‐covering with at most 6k ? 12 vertices of degree 7. We also construct, for every surface F² with Euler genus k ≥ 2, a 3‐connected graph G on F² with arbitrarily large representativity each of whose 2‐connected 7‐coverings contains at least 6k ? 12 vertices of degree 7. © 2003 Wiley Periodicals, Inc. J Graph Theory 43: 26–36, 2003     

Transition‐metal‐catalyzed reactions of 5‐methylene‐2‐oxazolidinone and 5‐methylene‐1,3‐thiazolidine‐2‐thione with isocyanates

5‐Methylene‐2‐oxazolidinone (1) and 5‐methylene‐1,3‐thiazolidine‐2‐thione (4) react with various isocyanates to give the corresponding urethanes 3 and 5 in high yields in the presence of palladium(0) or palladium(II) catalyst under mild reaction conditions. A mechanism is proposed. Copyright © 2003 John Wiley & Sons, Ltd.     

Focused ion beam Moiré method

A focused ion beam (FIB) Moiré method is proposed to measure the in-plane deformation of object in a micrometer scale. The FIB Moiré is generated by the interference between a prepared specimen grating and FIB raster scan lines. The principle of the FIB Moiré is described. The sensitivity and accuracy of deformation measurement are discussed in detail. Several specimen gratings with 0.14 and 0.20 μm spacing are used to generate FIB Moiré patterns. The FIB Moiré method is successfully used to measure the residual deformation in a micro-electro-mechanical system structure after removing the SiO₂ sacrificial layer with a 5000 lines/mm grating. The results demonstrate the feasibility of this method.     

Formation of p-type ZnO film on InP substrate by phosphor doping

ZnO thin film was initially deposited on InP substrate by radio frequency (rf) magnetron sputtering and the diffusion process was performed using the closed ampoule technique where Zn₃P₂ was used as the dopant source. To verify the junction formation of ZnO thin films, the electrical properties were measured, and the effects of Zn₃P₂ diffusion on ZnO thin films were investigated. It is observed that the electrical property of the film is changed from n-type to p-type by dopant diffusion effect. Based on the results, it is confirmed that ZnO thin films can be a potential candidate for ultraviolet (UV) optical devices.     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

Dihalodimethyltin(IV) complexes of 2‐(pyrazol‐1‐ylmethyl)pyridine

Reaction of dichloro‐ and dibromodimethyltin(IV) with 2‐(pyrazol‐1‐ylmethyl)pyridine (PMP) afforded [SnMe₂Cl₂(PMP)] and [SnMe₂Br₂(PMP)] respectively. The new complexes were characterized by elemental analysis and mass spectrometry and by IR, Raman and NMR (¹H, ¹³C) spectroscopies. Structural studies by X‐ray diffraction techniques show that the compounds consist of discrete units with the tin atom octahedrally coordinated to the carbon atoms of the two methyl groups in a trans disposition (Sn? C = 2.097(5), 2.120(5) Å and 2.110(6), 2.121(6) Å in the chloro and in the bromo compounds respectively), two cis halogen atoms (Sn? Cl = 2.4908(16), 2.5447(17) Å; Sn? Br = 2.6875(11), 2.7464(9) Å) and the two donor atoms of the ligand (Sn? N = 2.407(4), 2.471(4) Å and 2.360(5), 2.455(5) Å). In both cases, the Sn? N(pyridine) bond length is markedly longer than the Sn? N(pyrazole) distance. Copyright © 2003 John Wiley & Sons, Ltd.