Determination of loads applied perpendicularly to the outer boundary of a ring using coefficients of influence

A procedure is explained to determined the amount of several pairs of diametrical loads applied to the outside boundary of a ring when stresses at selected points of the inside or outside boundaries are known. Coefficients of influence are used, following an approach similar to the one presented in a previous paper. Examples of application are given and the possible increase in precision is shown when the number of points of measurements is larger than the number of loads to be determined.     

Synthesis of fluorinated analogues of the neurosteroid GABAA receptor antagonist, 17-PA

The steroid 17-PA is a GABA_A receptor antagonist which is finding use as a tool in evaluating agonistic/antagonistic activity at GABA_A receptors. Compounds with improved efficacy over 17-PA would be are advantageous for such studies. Accordingly a series of novel analogues of the neurosteroid 17-PA have been prepared and a convenient two-step route is presented which is amenable to the synthesis of analogues with electron-donating para-aromatic substituents including fluorine. However, for the meta-fluoro analogue then the original four-step route to 17-PA remains more efficient overall. The paper describes these syntheses and discusses the electronic factors which influence this synthetic chemistry.     

Single-molecule observation of the catalytic subunit of cAMP-dependent protein kinase binding to an inhibitor peptide

An engineered version of the staphylococcal alpha-hemolysin protein pore, bearing a peptide inhibitor near the entrance to the beta barrel, interacts with the catalytic (C) subunit of cAMP-dependent protein kinase. By monitoring the ionic current through the pore, binding events are detected at the single-molecule level. The kinetic and thermodynamic constants governing the binding interaction and the synergistic effect of MgATP are comparable but not identical to the values in bulk solution. Further, the values are strongly dependent on the applied membrane potential. Additional exploration of these findings may lead to a better understanding of the properties of enzymes at the lipid/water interface. Despite the complications, we suggest that the engineered pore might be used as a sensor element to screen inhibitors that act at either the substrate or ATP binding sites of the C subunit.     

IMPAIRED REPAIR OF UVC-INDUCED DNA DAMAGE IN L5178Y-R CELLS: SEDIMENTATION STUDIES WITH THE USE OF 5''-BROMODEOXYURIDINE PHOTOLYSIS

Abstract Relative to their L5178Y-S counterparts, L5178Y-R cells have an impaired capacity to form patches in DNA after exposure to UVC radiation. The photolysis of 5'-bromodeoxyuridine (BrdUrd) incorporated into DNA was used to estimate the number of 'repair patches'formed in response to a 254 nm UV (UVC) exposure. L5178Y-S cells, typical of rodent cell lines, formed a small number of patches in exposed DNA (1-2 patches per 1 times 10⁸ dalton during a 6 h recovery after an exposure of 20 J/m²). In contrast, DNA extracted from L5178Y-R cells exposed to UVC and subsequently incubated with BrdUrd for 6 h showed no evidence of BrdUrd incorporation indicating no capacity to form sites of repair (fewer than 0.5 sites of BrdUrd incorporation per 1 times 10⁸ dalton). Moreover, in L5178Y-R cells high fluences of UVC caused an extensive DNA degradation. Such degradation was not observed in L5178Y-S cells during the 24-h post-exposure period. These results are consistent with the notion that L5178Y-R cells have a reduced capacity to repair DNA damage induced by UVC radiation.     

Uniform molecular analysis using femtosecond laser mass spectrometry

The potential of femtosecond laser time-of-flight mass spectrometry (FLMS) for uniform quantitative analysis of molecules has been investigated. Various samples of molecular gases and vapours have been studied, using ultra-fast ( approximately 50 fs) laser pulses with very high intensity (up to 1.6 x 10(16) Wcm(-2)) for non-resonant multiphoton ionisation/tunnel ionisation. Some of these molecules have high ionisation potentials, requiring up to ten photons for non-resonant ionisation. The relative sensitivity factors (RSF) have been determined as a function of the laser intensity and it has been demonstrated that for molecules with very different masses and ionisation potentials, uniform ionisation has been achieved at the highest laser intensities. Quantitative laser mass spectrometry of molecules is therefore a distinct possibility. Copyright 1999 John Wiley & Sons, Ltd.     

The Instability of Nonmonotonic Wave Solutions of Parabolic Equations

We consider the class of equations u_t=f(u_xx, u_x, u) under the restriction that for all a,b,c. We first consider this equation over the unbounded domain ? ∞ < x < + ∞, and we show that very nearly every bounded nonmonotonic solution of the form u(t, x)=?(x?ct) is unstable to all nonnegative and all nonpositive perturbations. We then extend these results to nonmonotonic plane wave solutions u(t, x, y)=?(x?ct) of u_t = F(u_xx, u_xy, u_x, u_y, u). Finally, we consider the class of equations u_t=f(u_xx, u_x, u) over the bounded domain 0 < x < 1 with the boundary conditions u(t, x)=A at x=0 and u(t, x)=B at x=1, and we find the stability of all steady solutions u(t, x)=?(x).     

Effects of sonication on electrode surfaces and metal particles

Ultrasonic irradiation at a frequency of 20 kHz has varying effects on electrode surfaces. Non-metals such as glassy carbon and Ebonex™ are severely pitted after only a few minutes of sonication in aqueous media. By contrast, metals such as Pt, Au, W and Pd remain largely undamaged after 120 s, as observed by scanning electron microscopy. The extent of damage does not appear to be related to the melting point of the material. By contrast, when electrodes are sonicated in suspensions of metal powders, particles are deposited onto electrode surfaces. The deposits were subsequently observed by scanning electron microscopy and by voltammetry. It is concluded that the ability to deposit particles on an electrode depends on both the melting point of the particles and the electrode, whereas surface damage is more closely related to the hardness of the material.