白光干涉条纹变密的原因探讨

讨论了在测定透明介质折射率的过程中彩色条纹变密的现象，并在其基础上分析其成因：一是由于媒质折射率加大；二是由于平形板介质平行度不好造成楔形的倾角变大，最后在实验中验证了理论结果。     

Possible triggering of solar activity to big earthquakes (Ms ≥ 8) in faults with near west-east strike in China

A big earthquake (Ms = 8.1) occurred at western Kunlun Mts gap on November 14, 2001. It is the biggest earthquake in China in the past 50 years and the only one with a magnitude bigger than 8 in China after Dangxiong Earthquake (M = 8) in Tibet in 1951. The big earthquake has drawn wide attention of scientists in seismological, geophysical, geological and astro-geodynamic circles. Scientists are interested in the occurrence regularity of the very big earthquakes and try to find out the fac…     

利用计算机辅助装调检测矩形大口径离轴非球面的方法研究

通过非球面的零位补偿法,完成了对矩形大口径离轴非球面镜的检测。先用光学设计软件Zemax从理论上分析了在检测中会出现的现象,并结合计算机辅助装调技术,确定在检测过程中相对敏感的自由度,然后控制这些量,使补偿器和非球面的相对关系与理论设计相吻合,在Zygo相位干涉仪上测得最终结果。在λ=632.8nm时,中心圆口径与两个边缘圆口径面形误差RMS分别为0.022λ,0.037λ,0.032λ。检测结果,达到预期目的。     

CCD相机调制传递函数测试软件的研制

数学傅立叶分析法是测量调制传递函数常用的一种方法，为了迅速地给出采用该方法进行调制传递函数测试的结果，针对刀口扫描测试CCD相机调制传递函数的测试系统研制了测试软件。软件可读入CCD相机摄取的数字图像文件，对数据进行消噪声处理，并自动识别刀口位置，选择合适区域计算出相机的调制传递函数。软件采用VC语言编制，结果以列表和曲线两种形式输出，用户界面良好，使用方便。利用该软件得到的测试结果与俄罗斯软件的计算结果吻合较好。     

Surface roughness investigation of semi-conductor wafers

Conventionally, surface roughness is predominantly determined through the use of stylus instruments. However, there are certain limitations involved in the method, particularly when a test specimen, such as a silicon wafer, has a smooth mirror-like surface. Hence, it is necessary to explore alternative non-contact techniques. Light scattering has recently been gaining popularity as an optical technique to provide prompt and precise inspection of surface roughness. In this paper, the total integrated scattering (TIS) model is modified to retrieve parameters on surface micro-topography through light scattering. The applicability of the proposed modified TIS model is studied and compared with an atomic force microscope. Experimental results obtained show that the proposed technique is highly accurate for measuring surface roughness in the nanometer range.     

带有随机因素的逆DEA模型

本文讨论含有随机因素的逆 DEA模型 .逆 DEA模型解决的问题是 :对于某个决策单元 (DMU ) ,若增加其输入 ,在保持相对效率水平不变的情况下 ,估计 (预测 )输出应增加多少 .因此逆 DEA模型可用于短期预测问题 .带有随机因素的逆 DEA模型 ,是将该问题转化成机会约束的多目标规划问题 ,在某些特殊情况下 ,成为机会约束的线性规划问题 .     

An enantioselective Michael addition of malonate to nitroalkenes catalyzed by low loading demethylquinine salts in water

An enantioselective Michael addition of malonate to nitroalkenes is efficiently catalyzed by low loading demethylquinine salts in water; the yield range from 49% to 93% and the ee up to 90%.     

SiH4激光等离子体内自由基反应动力学研究

本工作采用时间分辨的OES(Optics Emission Spectroscopy)技术,研究横向激励大气压(TEA)CO₂激光诱发的SiH₄等离子体内碎片反应动力学过程。实验结果表明,等离子体内某些碎片的发光特征谱线主峰位置明显不同。据此,讨论了各碎片的产生及反应过程。比较各碎片发光的持续时间及综合其它OES结果,我们认为SIH₄激光等离子体的最终反应通道为产生Si的通道。 关键词：     

Low-energy ion-assisted control of interfacial structures in metallic multilayers

A molecular dynamics method has been used to simulate the argon ion-assisted deposition of Cu/Co/Cu multilayers and to explore ion beam assistance strategies that can be used during or after the growth of each layer to control interfacial structures. A low-argon ion energy of 5–10 eV was found to minimize a combination of interfacial roughness and interlayer mixing (alloying) during the ion-assisted deposition of multilayers. However, complete flattening with simultaneous ion assistance could not be achieved without some mixing between the layers when a constant ion energy approach was used. It was found that multilayers with lower interfacial roughness and intermixing could be grown either by modulating the ion energy during the growth of each metal layer or by utilizing ion assistance only after the completion of each layers deposition. In these latter approaches, relatively high-energy ions could be used since the interface is buried and less susceptible to intermixing. The interlayer mixing dependence upon the thickness of the over layer has been determined as a function of ion energy.     

Synthesis of grafted poly(p‐phenyleneethynylene) with energy donor–acceptor architecture via atom transfer radical polymerization: Towards nonaggregating and hole‐facilitating light‐emitting material

In this contribution, we demonstrate a new effective methodology for constructing highly efficient and durable poly(p‐phenyleneethynylene) (PPE) containing emissive material with nonaggregating and hole‐facilitating properties through the introduction of hole‐transporting blocks into the PPE system as the grafting coils as well as building the energy donor–acceptor architecture between the grafting coils and the PPE backbone. Poly(2‐(carbazol‐9‐yl)ethyl methacrylate) (PCzEMA), herein, is chosen as the hole‐transporting blocks, and incorporated into the PPE system as the grafting coils via atom transfer radical polymerization. The chemical structure of the resultant copolymer, PPE‐g‐PCzEMA, was characterized by NMR and gel permeation chromatography, showing that the desirable copolymer was obtained with the narrow polydispersity. The increased thermal stability of PPE‐g‐PCzEMA was confirmed by thermogravimetric analysis and differential scanning calorimetry along with its macroinitiator. The optoelectronic properties of this copolymer were studied in detail by ultraviolet‐visible absorption, photoluminescence emission and excitation spectra, and cyclic voltammogram (CV). The results indicate that PPE‐g‐PCzEMA exhibits the solid‐state luminescent property dominated by individual lumophores, and also the energy transfer process from the PCzEMA blocks to the PPE backbone with a relatively higher energy transfer efficiency in the solid‐state compared to that of the solution state. Additionally, the hole‐injection property is greatly facilitated due to the presence of PCzEMA, as confirmed by CV profiles. All these data indicate that PPE‐g‐PCzEMA is a good candidate for use in optoelectronic devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3776–3787, 2007