Mixing characteristics of motionless mixers

Motionless mixers have found a large range of applications, including blending, reaction, dispersion, heat transfer and mass transfer. Understanding the mixing processes that occur in these diverse systems is essential for predicting many aspects of practical importance. The objective of this study is to perform the experimental investigations of mixing characteristics for three different motionless mixers. The red color dye tracer was mixed in the main stream of green hair styling gel, and then the mixing efficiency was quantified by calculating the percentage area concentration of red color at the outlet cross section using a digital image processing technique. In the Sulzer SMX and YHC mixer, a single element mixes the fluid nearly in two dimensions, and three-dimensional mixing is accomplished by the next elements aligned at 90o to their former one. In the Sulzer SMX mixer, the flow appears to be globally well mixed after 5 elements, while in the YHC and YNU mixers, it is necessary to globally well mix more than 1 and 2 elements.     

First measurement of the ϱ spectral function in nuclear collisions

The NA60 experiment at the CERN SPS has studied low-mass muon pairs in 158 A GeV In–In collisions. A strong excess of pairs is observed above the yield expected from neutral meson decays. The unprecedented sample size close to 400000 events and the good mass resolution of about 2% made it possible to isolate the excess by subtraction of the decay sources. The shape of the resulting mass spectrum shows some non-trivial centrality dependence, but is largely consistent with a dominant contribution from π⁺π^-→ϱ→μ⁺μ^- annihilation. The associated ϱ spectral function exhibits considerable broadening, but essentially no shift in mass. The p_T-differential mass spectra show the excess to be much stronger at low p_T than at high p_T. The results are compared to theoretical model predictions; they tend to rule out models linking hadron masses directly to the chiral condensate. PACS 25.75.-q; 12.38.Mh; 13.85.Qk     

Preparation of Fe–Si–B–Nb amorphous powder cores with excellent high-frequency magnetic properties

FeSiBNb amorphous powder cores were prepared with the amorphous powder by gas atomization and subsequent hot pressing of resulting powder after creating oxide layers on the amorphous powder. Fully amorphous FeSiBNb powders with good soft magnetic properties were successfully obtained in the particle size range below 100 μm. FeSiBNb amorphous powder cores exhibit stable permeability up to 10 MHz, showing excellent high-frequency characteristics.     

Quantitative methods for nanopowders characterization

The size, shape and surface topology have a strong influence on powders properties, such as: mechanical, optical, catalytic, etc. In addition, when particles have a nanometer size, the dispersion of these features plays an important role.There are a number of techniques, which could be used in order to characterize powders in terms of particle size and shape. However, due to the scale of analysis, well beyond the wavelength of visible light, most of them cannot be applied for investigations of nanopowders.In this paper, transmission electron microscopy (TEM) image analysis and X-ray methods are presented as promising and complementary techniques. An example of their application to ZrO₂ nanopowder is shown. The advantages and limitations of each method are described.     

Infrared reflection absorption study of carbon monoxide adsorption on Pd/Cu(1 1 1)

Pd-Cu bimetallic surfaces formed through a vacuum-deposition of Pd on Cu(1 1 1) have been discussed on the basis of carbon monoxide (CO) adsorption: CO is used as a surface probe and infrared reflection absorption (IRRAS) spectra are recorded for the CO-adsorbed surfaces. Low energy electron diffraction (LEED) patterns for the bimetallic surfaces reveal six-fold symmetry even after the deposition of 0.6 nm. The lattice spacings estimated by the separations of reflection high-energy electron diffraction (RHEED) streaks increase with increasing Pd thickness. Room-temperature CO exposures to the bimetallic surfaces formed by the Pd depositions less than 0.3 nm thickness generate the IRRAS bands due to the three-fold-hollow-, bridge- and linear-bonded CO to Pd atoms. In particular, on the 0.1 nm-thick Pd surface, the linear-bonded CO band becomes apparent at an earlier stage of the exposure. In contrast, the bridge-bonded CO band dominates the IRRAS spectra for CO adsorption on the 0.6 nm-thick Pd surface, at which the lattice spacing corresponds to that of Pd(1 1 1). A 90 K-CO exposure to the 0.1 nm-thick Pd surface leads to the IRRAS bands caused not only by CO-Pd but also by CO-Cu, while the Cu-related band is almost absent from the spectra for the 0.3 nm-thick Pd surface. The results clearly reveal that local atomic structures of the outermost bimetallic surface can be discussed by the IRRAS spectra for the probe molecule.     

Study of the order–disorder transition and martensitic transformation in a Cu–Al–Be alloy by EELS

Changes in 3d states occupancy associated with order–disorder transition and martensitic transformation in a Cu–Al–Be alloy was investigated by electron energy loss spectroscopy (EELS) in both high energy and low energy loss regions. From the high energy loss region, the Cu L_2,3 white-line intensities, which reflect the unoccupied density of states in 3d bands, was measured for three states of the alloy: disordered austenite, ordered austenite and martensite. It was found that the white-line intensity remains the same during order–disorder transition but appears slightly smaller in martensite, indicating that some electrons left Cu 3d bands or some hybridization took place during phase transformation. From the low energy loss region, the optical joint density of states (OJDS) was obtained by Kramers–Kronig analysis. As maxima observed in the OJDS spectra are assigned to interband transitions, these spectra can be used to probe changes in the electronic band structure. The analysis shows that during the martensitic transformation, the peaks positions and relative intensities in the OJDS spectra undergoes noticeable changes, which are associated with interband transitions.     

Quantitative analysis of multi-element oxide thin films by angle-resolved XPS: Application to ultra-thin oxide films on MgAl substrates

An original procedure has been developed for the quantitative analysis and microstructural interpretation of angle-resolved X-ray photoelectron spectra (AR-XPS) of very thin (<6 nm), multi-element oxide films as grown on metallic binary alloy substrates by, e.g., thermal or plasma oxidation. To this end, first an approach has been given to retrieve the different metallic, oxidic and oxygen primary zero-loss (PZL) intensities from the measured AR-XPS spectra of the bare and oxidized alloy. The principal equations for the determination of the oxide-film thickness, composition and constitution from the resolved PZL intensities have been presented. On this basis, various corresponding calculation routes have been distinguished. The procedure has been applied to the case of very thin (<6 nm), mixed (Mg, Al)-oxide films on bare Mg-based MgAl substrates as grown by dry, thermal oxidation at room temperature. The results obtained on the thickness, composition, defect structure and constitution of the oxide-film have been discussed as function of the bulk Al alloying content and the applied partial pressure of oxygen.     

Magnetization reversal of micropattern Fe bar array: Combination of vector and Bragg magneto-optical Kerr effect measurements

We report on a magneto-optical Kerr effect (MOKE) investigation of alternating wide and narrow Fe bars, forming a two-dimensional periodic array. The magnetization reversal was studied by regular longitudinal Vector-MOKE in specular geometry as well as in Bragg-MOKE geometry, using the diffraction spots from the grating for hysteresis measurements. With Vector-MOKE a two-step switching process for the wide and narrow Fe bars is observed, indicative for a narrow switching field distribution in this array. In addition, hysteresis loops were determined as a function of the diffraction order for the hard and easy axis direction. The loops at different orders of diffraction can qualitatively and quantitatively be described by Fourier transformations of micromagnetic simulations.     

Differential AC-chip calorimeter for glass transition measurements in ultrathin films

A differential AC-chip calorimeter capable of measuring the step in heat capacity at the glass transition in nanometer-thin films is described. Because of the differential setup, pJ/K sensitivity is achieved. Heat capacity can be measured for sample masses below 1 ng in broad temperature range as needed for the study of the glass transition in nanometer-thin polymeric films. Relative accuracy is sufficient to investigate the changes in heat capacity as the step at the glass transition of polystyrene. The step is about 25% of the total heat capacity of polystyrene. The calorimeter allows for the frequency dependent measurement of complex heat capacity in the frequency range from 1 Hz to 1 kHz. The glass transition in thin polystyrene films (50–4 nm) was determined at well-defined experimental time scales. No thickness dependency of the glass transition temperature was observed within the error limits (±3 K)—neither at constant frequency (40 Hz) nor for the trace in the activation diagram (1 Hz–1 kHz). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2996–3005, 2006     

Thermal stability of shear-induced precursor structures in isotactic polypropylene by rheo-X-ray techniques with couette flow geometry

Combined in situ rheo-SAXS (small-angle X-ray scattering) and -WAXD (wide-angle X-ray diffraction) studies using couette flow geometry were carried out to probe thermal stabilty of shear-induced oriented precursor structure in isotactic polypropylene (iPP) at around its normal melting point (162 °C). Although SAXS results corroborated the emerging consensus about the formation of “long-living” metastable mesomorphic precursor structures in sheared iPP melts, these are the first quantitative measures of the limiting temperature at which no oriented structures survive. At the applied shear, rate = 60 s⁻¹ and duration t_s = 5 s, the oriented iPP structures survived a temperature of 185 °C for 1 h after shear, while no stable structures were detected at and above 195 °C. Following Keller's concepts of chain orientation in flow, it is proposed that the chains with highly oriented high molecular weight fraction are primarily responsible for their stability at high temperatures. Furthermore, the effects of flow condition, specifically the shear temperature, on the distributions of oriented and unoriented crystals were determined from rheo-WAXD results. As expected, at a constant flow intensity (i.e., rate = 30 s⁻¹ and duration, t_s = 5 s), the oriented crystal fraction decreased with the increase in temperature above 155 °C, below which the oriented fraction decreased with the decrease in temperature. As a result, a crystallinty “phase” diagram, i.e., temperature versus crystal fraction ratio, exhibited a peculiar “hourglass” shape, similar to that found in many two-phase polymer–polymer blends. This can be explained by the competition between the oriented and unoriented crystals in the available crystallizable species. Below the shear temperature (155 °C), the unoriented crystals crystallized so rapidly that they overwhelmed the crystallization of the oriented crystals, thus depleting a major portion of the crystallizable species and increasing their contribution in the final total crystalline phase. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3553–3570, 2006