111In–L–LDL and 153Gd–L–LDL as radiotracers for detection of AR4‐2J rat pancreatic tumors

Pancreatic cancer has an extremely poor prognosis, due, in part, to lack of methods for early diagnosis. The present study was designed to evaluate the potential of labeling low‐density lipoprotein (LDL) with a radionuclide using a lipid chelating agent, bis(stearylamide) of diethylenetriaminepentaacetic acid (L), to detect pancreatic tumors by gamma‐scintigraphy. Previous studies indicated that the difficulty of visualization of pancreatic tumors was due to their poor vascularization. This study compares the ability of two radiotracers, ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL to target highly vascularized rat pancreatic tumors (AR4‐2J) implanted in nude mice. Biodistribution studies showed that the tumor uptake of ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL tracers was twofold and fivefold higher respectively than with the controls (¹¹¹In citrate and ¹⁵³Gd citrate respectively). These tracers would thus be suitable for scintigraphic imaging. We show here that LDL could be employed as a delivery system for tracers such as ¹¹¹In or ¹⁵³Gd when these two radionuclides are complexed by a lipid‐chelating anchor, and that ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL enabled better visualization of the pancreatic tumor tissues, with a better result with ¹⁵³Gd–L–LDL. Copyright © 2004 John Wiley & Sons, Ltd.     

On the evaluation of the nonisothermal kinetic parameters of (GeS2)0.3(Sb2S3)0.7 crystallization using the IKP method

The isoconversional method suggested by Friedman and the invariant kinetic parameters method (IKP) were used in order to examine the kinetics of the nonisothermal crystallization of (GeS₂)_0.3(Sb₂S₃)_0.7. The objective of the paper is to show the usefulness of the IKP method both for determining the activation parameters as well as the model of the investigated process. It was shown that the kinetic triplet [(E, A, f(α), where E is the activation energy, A is the preexponential factor, and f(α) is the differential function of conversion], which results through the application of the IKP method, depends on the set of kinetic models considered. For different sets of kinetic models, proportional values of f(α) are obtained. A criterion for the selection of this set, the use of which lead to the true kinetic triplet corresponding to the analyzed process (E = 163.2 kJ mol^?1; A = 2.47 × 10¹² min^?1 and the Avrami‐Erofeev model, A_m, for m = 2.5–2.6 was suggested. © 2004 Wiley Periodicals, Inc. Int J Chem Kinet 36: 309–315, 2004     

Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Synthesis and characterization of liquid crystalline side‐chain block copolymers containing luminescent 4,4′‐bis(biphenyl)fluorene pendants

A series of new liquid crystalline homopolymers, copolymers, and block copolymers were polymerized from styrene‐macroinitiator ( SMi ) and methacrylates with pendent 4,4′‐bis(biphenyl)fluorene ( M1 ) and biphenyl‐4‐ylfluorene ( M2 ) groups through atom transfer radical polymerization (ATRP). The number‐average molecular weights (Mn) of polymers P1 ‐ P4 were 10,007, 14,852, 6,275, and 10,463 g mol^?1 with polydispersity indices values of 1.21, 1.15, 1.31, and 1.22, respectively. All polymers exhibit the nematic phase. The thermal, mesogenic, and photoluminescent properties of all polymers were investigated. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4564–4572, 2007     

N. Charton,A. Feldermann,A. Theis,M. H. Stenzel,T. P. Davis,C. Barner‐Kowollik,Initiator efficiency of 2,2′‐azobis(isobutyronitrile) in bulk dodecyl acrylate free‐radical polymerizations over a wide conversion and molecular weight range (2004) 42(20) 5170–5179

The original article to which this Erratum refers was published in J Polym Sci Part A: Polym Chem (2004) 42(20) 5170–5179. No abstract.     

Photoinitiated cationic polymerization of cycloaliphatic epoxide with siloxane or alkoxysilane functionalized polyol coatings

Polyols were reacted with tetraethyl orthosilicate (TEOS) or 3-isocyanatopropyltriethoxysilane (IPTES) to form siloxane functionalized polyols. The UV-reactivity of these siloxane functionalized polyols were investigated using real-time FT-IR spectroscopy. The reactivity of TEOS modified polyols was dependent on the relative humidity. However, for the IPTES functionalized polyols the effect of relative humidity was dependent on the degree of IPTES functionalization. When the polyols were only partially functionalized with IPTES, the effect of relative humidity was minimal. However, when polyols were fully functionalized with IPTES, the curing was dependent on relative humidity. The siloxane functionalized polyols were formulated with a cycloaliphatic epoxide and cationic photoinitiator. The photo-induced curing kinetics of these cycloaliphatic epoxide/siloxane functionalized polyol coatings were also investigated. Unlike the TEOS functionalized polyols, the addition of IPTES functionalized polyols into the formulation inhibited the curing speed. This inhibition was attributed to the basicity nitrogen of the urethane linkage. The effect of relative humidity on the UV-curing reaction of cycloaliphatic epoxide coatings was lowered by the incorporation of the TEOS functionalized polyols.     

Metallothionein as a biomarker for mercury in tissues of rat fed orally with cinnabar

Cinnabar, as one of the most widely used mineral drugs in traditional Chinese medicines, has been proven to have prominent curative effects in clinical use for more than 2000 years. But the safety and toxicity of the drug has been under constant debate in clinic usage. Metallothionein (MT) contains about 30% of cysteine in the molecule, and plays an important detoxification role against heavy metals. In this study, it was used as a biomarker to assess mercurial accumulation in rats fed orally with cinnabar. After feeding rats with cinnabar by gastric gavage at different dosages and at different times, the distribution of heavy metals (including mercury, copper and zinc) and MT was investigated among rat tissues, including liver, kidney, heart, brain, testis and blood. Metals and MT determinations were carried out using inductively coupled plasma mass spectrometry (ICP‐MS) and a modified mercury saturation assay technique respectively. The results indicated that mercury was easily accumulated in the tissues of rats exposed to cinnabar, especially in kidney. For example: at a feeding dosage of 5 g kg^?1 (bw) for 4 weeks, the mercury concentrations in kidney were 13, 8.7, 21.6 and 26 times those in liver, testis, brain and heart respectively; and at 2.5 g kg^?1 (bw) for 2 weeks, the mercury concentrations in kidney were 21, 2.1, 3 and 21 times those in liver, testis, brain and heart respectively. In addition, mercury in kidney and liver of all cinnabar groups was significantly higher than that of the control group (P < 0.01). A high positive correlation observed between MT concentrations and mercury levels in both liver and kidney (R² = 0.9299, P < 0.02 for liver; R² = 0.9923, P < 0.0008 for kidney) indicated that MT could be used as a biomarker for mercury in tissues. Copyright © 2004 John Wiley & Sons, Ltd.