基于灰度曲线交点的结构光编码条纹边缘检测

在分析结构光编码白条纹扩散的原因和实际边缘形态的基础上,提出一种同时检测多边缘并消除扩散影响的亚像素精度方法--交点法.首先向被测表面投射互为反色的两组格雷编码图案,提取两组强度图像中灰度梯度较大的点作为边缘依据点,并对其进行曲线拟合,然后将对应拟合曲线的交点作为边缘.分析了交点法对结构光系统中常见的被测表面倾斜和离焦两个主要误差因素的适应能力.介绍了检测原理及误差因素分析,并进行了边缘检测实验.实验结果表明,对于宽度大于4 pixel的编码条纹,边缘检测相对误差小于1%,可消除被测表面倾斜和离焦的影响.     

太空育种射干的X射线荧光及X射线衍射分析和表征

联用X射线荧光光谱(XRF)和粉末X射线衍射(PXRD)方法,对我国独创的第4代太空诱变育种射干中多种元素种类和含量及晶态物质进行了研究。结果表明:太空组射干K元素含量比地面组、对照品分别提高了1.03和0.31倍,Mg元素分别提高了1.44和0.06倍,Ca,Mn和Fe元素含量比地面组分别提高了0.95,0.30和0.29倍,Al元素比地面组、对照组分别降低了38.5%和85.5%,并在射干中鉴别出一水草酸钙(CaC2O4.H2O)晶体,晶体含量是地面组<太空组<对照品。从而可得出结论:太空射干中人体必需的矿质元素比地面组都更接近或优于对照品。文章研究结果和方法对筛选品质优良的太空药材籽种和推广种植太空药材以及建立中药材质量评价标准,有积极的作用和重要意义。     

离散颗粒层被横向推移过程中的力学行为研究

研究发现,颗粒物质层被匀速推移挤压过程中,所需推移力先以线性规律增加,在某一确定点后,则会以指数规律增加.而颗粒物质是由众多离散颗粒组成的软凝聚态物质,其宏观上反映的是离散颗粒的个体性质和凝聚态物质的集体效应.颗粒与颗粒之间以及颗粒与边界之间的细观尺度接触力链的构成以及演变规律将会直接影响各种宏观受力情况,其摩擦力与挤压力便是力链的主要构成形式.围绕着定量描述细观力链特征,从而揭示力的变化规律这一目标,采用计算机模拟的方法,依照球形颗粒Hertz法向接触理论和Mindlin-Deresiewicz切向接触理论,对重力作用下不同数目的三维等径球体颗粒层的推移情况进行了离散元仿真模拟,量化分析了推移力变化规律、各摩擦力变化规律以及力链分布规律,发现摩擦力与挤压力在颗粒堆积的不同阶段对力链的构成起到了不同的主次作用,使得力链发生强弱演变,从而发现了推移颗粒物质层时推移力的变化规律及原因.这些结果有利于从力链角度揭示颗粒内部和颗粒与各边界之间的受力情况.     

Fabrication and characterization of rod-like nano-hydroxyapatite on MAO coating supported on Mg-Zn-Ca alloy

The poor corrosion resistance of magnesium alloys is a dominant problem that limits their clinical application. In order to solve this challenge, micro-arc oxidation (MAO) was used to fabricate a porous coating on magnesium alloys and then electrochemical deposition (ED) was done to fabricate rod-like nano-hydroxyapatite (RNHA) on MAO coating. The cross-section morphology of the composite coatings and its corresponding energy dispersion spectroscopy (EDS) surficial scanning map of calcium revealed that HA rods were successfully deposited into the pores. The three dimensional morphology and scanning electron microscopy (SEM) image of the composite coatings showed that the distribution of the HA rods was dense and uniform. Atomic force microscope (AFM) observation of the composite coatings showed that the diameters of HA rods varied from 95 nm to 116 nm and the root mean square roughness (RMS) of the composite coatings was about 42 nm, which were favorable for cellular survival. The bonding strength between the HA film and MAO coating increased to 12.3 MPa, almost two times higher than that of the direct electrochemical deposition coating (6.3 MPa). Compared with that of the substrate, the corrosion potential of Mg-Zn-Ca alloy with composite coatings increased by 161 mV and its corrosion current density decreased from 3.36 × 10⁻⁴ A/cm² to 2.40 × 10⁻⁷ A/cm² which was due to the enhancement of bonding strength and the deposition of RNHA in the MAO pores. Immersion tests were carried out at 36.5 ± 0.5 °C in simulated body fluid (SBF). It was found that RNHA can induce the rapid precipitation of calcium orthophosphates in comparison with conventional HA coatings. Thus magnesium alloy coated with the composite coatings is a promising candidate as biodegradable bone implants.     

Pressure dependence of the thermal stability in LiMn2O4

Structural stability in terms of the decomposition temperature in LiMn₂O₄ was systematically investigated by a series of high-temperature and high-pressure experiments.LiMn₂O₄ was found to have structural stability up to 5 GPa at room temperature.Under ambient pressure,the compound decomposed at 1300℃.The decomposition temperature decreased with increasing pressure,yielding more complex decomposed products.Below the decomposition temperature,the crystal structure of LiMn₂O₄ varied with pressure.The presented results in this study offer new insights into the thermal and pressure stability of LiMn₂O₄ materials as a cathode for lithium-ion batteries that can operate under extreme conditions.Therefore,these findings may serve as a useful guide for future work for improving lithium-ion batteries.     

Free boundary problem for a fully nonlinear and degenerate parabolic equation in an angular domain

This paper concerns with the problem of how to running an insurance company to maximize his total discounted expected dividends. In our model, the dividend rate is limited in $[0,M]$ and the company is allowed to transfer any proportion of risk by reinsuring. So there are two strategies which we call dividend strategy and reinsurance strategy. The objective function and the corresponding optimal two strategies are the solution and the two free boundaries of the following Barenblatt parabolic equation

$v_t?\underset{0\le a\le 1}{\max }?(\frac{1}{2}{a}^2{\sigma }^2{v}_{xx}+a\mu v_x)+cv?\underset{0\le l\le M}{\max }?[(1?v_x)l]=0$

under certain boundary conditions on an angular domain

$Q_T=\{(x,t)|0<x<Mt,0<t\le T\}.$

The main effort is to analyze the properties of the solution and the free boundaries to show the optimal decision for the insurance company.     

Diffusion Mechanism of As‐spun Polyacrylonitrile Fiber in a Dimethyl Sulfoxide‐Water Coagulation Bath

In this paper, the diffusion mechanism of as‐spun PAN fiber was investigated in dimethyl sulfoxide‐water by determining the dynamic compositions of the fibers and the diffusion coefficients of solvent and nonsolvent during coagulation. The diffusion process could be divided into two stages. Results showed that the first stage of the diffusion process was the most important during the whole process, which was fundamental to further study on the formation mechanism. Also, compared with wet spinning, the dry‐jet wet spinning method had the advantage of mild coagulating at a high jet‐stretch. At high concentrations, the diffusion coefficients increased and the ratio of solvent diffusion coefficient to nonsolvent diffusion coefficient decreased; an increasing temperature resulted in the increase of both diffusion coefficients with a decrease in their ratios. To some extent, for the PAN‐DMSO‐water system, the more the ratios D_s*/D_n* tended to 1, the more the cross‐section shapes of as‐spun PAN fiber tended to be circular.     

Further Studies on the Anionic Copolymerization of Styrene and Glycidyl Methacrylate in Toluene

Sequential anionic copolymerization of styrene and glycidyl methacrylate (GMA) was performed with the protection of argon under normal pressure, where styrene, GMA, toluene, THF, n-butyllithium and a small amount of lithium chloride (LiCl) were used as first monomer, second monomer, solvent, polar reagent, initiator and additive, respectively. Polystyrene-b-poly(glycidyl methacrylate) diblock copolymers (PS-b-PGMA) with well-defined structure and narrow molecular weight distribution were prepared by the copolymerization reaction of poly(styryl)lithium with GMA under certain temperatures. The copolymers were characterized using gel permeation chromatography (GPC), ¹H-NMR, ¹³C-NMR, thin layer chromatography (TLC) and hydrochloric acid-dioxane argentimetric methods. The effects of additives, copolymerization temperature and THF dosage on the copolymerization were studied. No chain transfer reaction of anionic polymerization of styrene in toluene was observed. Slightly broader molecular weight distribution of PS-b-PGMA was observed with the increase the GMA repeat units. Using THF/toluene blend solvent could reduce the polydispersity index (M _w /M _n ) and dissolve the copolymer better than toluene alone. Lower temperature (< -40°C) and LiCl are required to prepare PS-b-PGMA with narrower molecular weight distribution.     

A convenient synthesis of 2β,3α-dihydroxyurs-12-en-28-oic acid as a natural diastereoisomer of corosolic acid

2β,3α-Dihydroxyurs-12-en-28-oic acid（6） is a naturally occurring diastereoisomer of corosolic acid with glycogen phosphorylase inhibitory activity.A new strategy for the semi-synthesis of 6 was developed.Using the commercially available ursolic acid（1） as the starting materials,6 was synthesized through five facile reactions with a high stereoselectivity and an overall yield of 47.3%.The structure of 6 was confirmed by optical rotation.ESI-MS,¹H NMR and ¹³C NMR data.     

Understanding the Initial Decomposition Pathways of the n‐Alkane/Nitroalkane Binary Mixture

Addition of nitroalkanes into n‐alkanes can lower the activation barriers of free‐radical production and accelerate the decomposition of n‐alkanes at relatively low temperatures. Four initial decomposition mechanisms of the n‐butane/nitroethane binary mixture were proposed for the promoting effect and considered theoretically at the B3LYP, BB1K, BMK, MPW1K, and M06‐2X levels with MG3S basis set. Energetics above was compared to high‐level CBS‐QB3 and G4 calculations. Calculated results confirm the feasibility of the four initial decomposition pathways: (I) the C? NO₂ bond rupture of nitroethane to produce ethyl and ·NO₂, (II) HONO elimination from nitroethane followed by decomposition to ·OH and ·NO, (III) rearrangement of nitroethane to ethyl nitrite which further dissociates into CH₃CH₂O· and ·NO, and (IV) direct hydrogen‐abstraction of nitroethane with n‐butane.